2001 TOYOTA SEQUOIA battery

DI±1982
± DIAGNOSTICSAUDIO SYSTEM
2176 Author: Date:
2005 SEQUOIA (RM1146U)DE
*4
Slave Reset (Momentary Inter-
ruption)After the engine was started, component shown
by sub code was disconnected from system.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
DF
*4Master Error
Due to defective cognition of component with a
display, master function is switched to audio
equipment.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy) *7
4. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
5. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *6
6. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±1993
DI±2058
DI±2110
DI±2023
DI±2061
DI±2139
±
±
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: If the power connector is disconnected after the engine starts, this code is recorded after 180 se-
conds.

*3: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*4: This code may be stored if the ignition key is held in the START position for 1 minute or more before
returning to the ON position.

*5: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*6: w/ Rear seat audio system only.

*7: w/ Rear seat entertainment system only.

± DIAGNOSTICSAUDIO SYSTEM
DI±1983
2177 Author: Date:
2005 SEQUOIA (RM1146U)
Logical address: 01 (Communication control) continued
DTCNameDiagnosisVerificationSee page
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E2ON/OFF Instruction Parameter
ErrorError occurs in ON/OFF controlling command
from master component.Replace radio receiver assy.±
E3
*1Registration Request Transmis-
sion
Registration Request command is output from
component shown by sub code.
Receiving Connection Check Instruction, Regis-
tration Request command is output from sub±
master component.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.
(b) Logical address: 61 (Cassette switch)
DTCNameDiagnosisVerificationSee page
40Mechanical Error of MediaMalfunction due to mechanical failure is identified.
Either that, or cassette tape is cut or entangled.1. Inspect cassette tape.
2. Replace radio receiver assy.±
±
(c) Logical address: 62 (CD player)
DTCNameDiagnosisVerificationSee page
42No Disc ReadoutDisc cannot be read.1. Inspect CD.
2. Replace radio receiver assy.±
±
44CD player ErrorError is detected in CD player.Replace radio receiver assy.±
47Detection of high temperatureHigh temperature is detected in CD player.
With ignition switch off, leave ve-
hicle in cool shaded place for a
while and recheck. After deleting
the DTC memory, if same code de-
tected, replace radio receiver assy.
±
48Detection of excess currentOver current is present in CD player.Replace radio receiver assy.±
(d) Logical address: 63 (In±dash CD changer)
DTCNameDiagnosisVerificationSee page
42No Disc ReadoutDisc cannot be read.1. Inspect CD.
2. Replace radio receiver assy.±
±
44CD player ErrorError is detected in CDDH.Replace radio receiver assy.±
47Detection of high temperatureHigh temperature is detected in CDCH.
With ignition switch off, leave ve-
hicle in cool shaded place for a
while and recheck. After deleting
the DTC memory, if same code de-
tected, replace radio receiver assy.
±
48Detection of excess currentOver current is present in CDCH.Replace radio receiver assy.±

± DIAGNOSTICSAUDIO SYSTEM
DI±1985
2179 Author: Date:
2005 SEQUOIA (RM1146U)
Logical address: 01 (Communication control) continued
DTCNameDiagnosisVerificationSee page
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E1
*1Audio processor ON errorWhile source equipment is operating, AMP output
stops.
1. Power source circuit (Radio re-
ceiver assy).
2. Power source circuit (Stereo
component amplifier assy).
3. AVC±LAN circuit (Radio receiver
assy ± Stereo component ampli-
fier assy).
4. AVC±LAN (Radio receiver assy
± Rear seat audio controller). *5
5. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy). *6
6. Replace radio receiver assy.
7. Replace stereo component am-
plifier assy.DI±1990
DI±1993
DI±2023
DI±2061
DI±2139
±
±
E2ON/OFF Instruction Parameter
ErrorError occurs in ON/OFF controlling command
from radio receiver assy.Replace radio receiver assy.±
E3
*1Registration Request Transmis-
sionRegistration Request command is output from
slave component.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*3: This code may be stored if the ignition key is held in the START position for one minute or more
before returning to the ON position.

*4: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*5: w/ Rear seat audio system only.

*6: w/ Rear seat entertainment system only.

± DIAGNOSTICSAUDIO SYSTEM
DI±1987
2181 Author: Date:
2005 SEQUOIA (RM1146U)E0
*1
Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Multi±display controller sub±
assy).
3. Replace Multi±display controller
sub±assy.DI±1990
DI±2139
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting an engine.

*2: This code is stored when 180 sec. has passed after the power supply connector is pulled out after
engine start.

*3: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position in 1 minute after engine start.

*4: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position after engine start.
Rear seat audio controller (Physical address: 1F4) [RSA]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
RSA panel was disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
D7
*2Connection Check Error
Component in which this code is recorded has
been disconnected from system after engine start.
Or, when this code was recorded, RSA panel was
disconnected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DC
*3Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*4Master Reset (Momentary Inter-
ruption)Component that is to be master has been discon-
nected after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±

DI±1988
± DIAGNOSTICSAUDIO SYSTEM
2182 Author: Date:
2005 SEQUOIA (RM1146U)E0
*1
Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
D8
*2No Response To Connection
CheckComponent shown by sub±code is or had been
disconnected from system after engine start.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
D9
*1Last Mode Error
Component operated (sound and/or image was
provided) before engine stop is or was discon-
nected with ignition switch in ACC or ON.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DANo Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Detected when sound and picture does not
change by button operation
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DB
*1Mode Status ErrorDual alarm is detected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
DC
*4Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DE
*3Slave Reset (Momentary Inter-
ruption)After engine start, slave component has been dis-
connected.
1. Power source circuit (Radio re-
ceiver assy).
2. AVC±LAN (Radio receiver assy
± Rear seat audio controller).
3. Replace Rear seat audio control-
ler.DI±1990
DI±2061
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

I28499
Built±in Type Amplifier:
Radio Receiver Assy A36
ACC Cut Relay Sub J/B No. 3
Instrument Panel J/B
Engine Room J/BTo ECM
Battery
IFR2
R2
R2 12
3A1
3A
1
4 3 W±R
2
GR B C B±O
J37 J38
IA124
L±Y L±Y GR
2B
2C8
2D1 RAD No. 1
ECU±BShort Pin 3
W±R
BRB RAD No. 2
3
1 6AM1 212 1
P
31ALT
5
B
I18
Ignition SWW±L1 2
AACC+B
GND BU+B 4 3
7 W±R
1J
1E
1L 1C1C1F
ACCAM1
GR
8
F10
Fusible Link Block
4 WJ/C
J12
Junction
Connector DI±1990
± DIAGNOSTICSAUDIO SYSTEM
2184 Author: Date:
2005 SEQUOIA (RM1146U)
CIRCUIT INSPECTION
Power source circuit (Radio receiver assy)
CIRCUIT DESCRIPTION
This circuit provides power to the radio receiver assy.
WIRING DIAGRAM
DID9U±01

I28498
11 Radio Receiver Assy
ACC+B
1
R420
GND GR 1
RAD No. 24 3 A36
ACC Cut Relay
P
31AM1 ACC12 Sub J/B No. 3
3AW±R
W±R1
IA124
L±Y L±Y
2B
3
2C8
2D1 Engine Room J/B
RAD No. 1
ECU±BShort Pin 1J3
1E
W±R
1L1
1C6AM12
ALT
5
B
Battery
IOBR Separate Type Amplifier:
R4 R4 3A
I18
Ignition SWW±LB 212 1
1C 1FGR
GRB C B±O
J37To ECM
J38
Instrument Panel J/B
1 2BU+B
W
8
4 F10
Fusible Link BlockJ/C
± DIAGNOSTICSAUDIO SYSTEM
DI±1991
2185 Author: Date:
2005 SEQUOIA (RM1146U)

I28739
Separate Type Amplifier
Wire Harness View:
GND ACC+B
BU+B
R4
I28743
Built±in Type Amplifier
Wire Harness View:
GND
ACC+BBU+B R2
DI±1992
± DIAGNOSTICSAUDIO SYSTEM
2186 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Inspect radio receiver assy.
PREPARATION:
Disconnect the radio receiver assy connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Symbol
(Tester connection)ConditionSpecified condition
GND (R2±7, R4±20) ±
Body groundAlwaysBelow 1 W
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Symbol
(Tester connection)ConditionSpecified condition
BU+B (R2±4, R4±1) ±
GND (R2±7, R4±20)Always10 to 14 V
ACC+B (R2±3, R4±11) ±
GND (R2±7, R4±11)Ignition SW ACC10 to 14 V
NG Repair or replace harness or connector
(Radio receiver assy ± battery or body ground).
OK
Proceed to next circuit inspection shown in problem symptoms table or diagnostic trouble code
chart (See page DI±1967 or DI±1979).