2001 TOYOTA SEQUOIA DLC3 Ts

I28577
Wire Harness Connector
Front View:
R6
IG
T
E
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1647
1841 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
LIGHT RHEOSTATLight Control Rheostat /
Min.: 0 Max.: 255Light control rheostat switch is
Dark (0) " Bright (255)
OK:
Light brightness can be changed within the specified range by manual operation.
OK Replace combination meter.
(See page IN±35)
NG
2 Check harness and connector (Power source circuit).
PREPARATION:
Disconnect the R6 light control rheostat switch connector.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Terminal No. (Symbol)ConditionSpecified condition
R6±5 (E) ± Body groundAlwaysBelow 1 W
CHECK:
Measure the voltage according to the value(s) in the table be-
low.
OK:
Terminal No. (Symbol)ConditionSpecified condition
R6±4 (T) ± Body groundLight control switch
TAIL or HEAD10 to 14 V
R6±1 (IG) ± Body groundIgnition switch ON10 to 14 V
NG Repair or replace harness or connector.
OK

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1651
1845 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SEAT BELT BUZZROFF / ONConfirm that the vehicle is stopped and engine is
idling.
D BELT REMINDOFF / ONConfirm that the vehicle is stopped and engine is
idling.
OK:
Switch condition (ON/OFF) can be switched by ACTIVE TEST.
NG Replace combination meter
(See page IN±35).
OK

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1655
1849 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
OIL PRESS METERHIGH, 3/4, 1/2, 1/4, LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
OK:
Oil pressure receiver gauge readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK

I01278
DI±1656
± DIAGNOSTICSCOMBINATION METER SYSTEM
1850 Author: Date:
2005 SEQUOIA (RM1146U)
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
OIL GAUGEOil Gauge /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the oil pressure receiver
gauge angle.

OK:
Oil pressure displayed on the tester is almost the same as the actual oil pressure.
OK Replace combination meter.
(See page IN±35)
NG
3 Inspect oil pressure sender gauge.
PREPARATION:
Disconnect the connector from the oil pressure sender.
CHECK:
(a) Check that no continuity exists between the terminal and
ground with the engine stopped.
(b) Check that continuity exists between the terminal and
ground with the engine running.
HINT:
Oil pressure should be over 24.5 kPa (0.25 kgf/cm
2, 3.55 psi).
OK:
When engine is stopped:
No continuity
When engine is running:
Continuity
NG Replace oil pressure sender gauge.
OK

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1659
1853 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
VOLT METER9 V / 12 V / 15 V / 18VConfirm that the vehicle is stopped and engine is
idling.
OK:
Volt meter readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK
2 Check fuse.
CHECK:
Measure the resistance of the IGN1 fuse in the instrument panel J/B.
OK:
Below 1 W
CHECK:
Measure the resistance of the AM2 fuse in the engine room J/B.
OK:
Below 1 W
NG Inspect for short circuit in harness and all com-
ponents connected to fuse.
OK

DID4Z±01
DI±1666
± DIAGNOSTICSSLIDING ROOF SYSTEM
1860 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand±held tester, you can read the value of the switch, sensor,
actuator and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting is one
of the method to shorten the labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, read the ºDATA LISTº.
SLIDE ROOF:
ItemMeasurement Item/
Display (Range)Normal conditionDiagnostic Note
LIMIT SW 1Position SW NO.1/
ON or OFFON: 250 mm point from fully opened position
OFF: Sliding roof fully closed position±
LIMIT SW 2Position SW NO.2/
ON or OFFON: Sliding roof fully closed position
OFF: Sliding roof except fully closed position±
OPEN SWSliding roof open SW
signal/ON or OFFON: Sliding roof is open
OFF: Sliding roof is close±
CLOSE SWSliding roof close SW
signal/ON or OFFON: Sliding roof is close
OFF: Sliding roof is open±
UP SWSliding roof up SW sig-
nal/ON or OFFON: Sliding roof is up
OFF: Sliding roof is down±
DOWN SWSliding roof down SW
signal/ON or OFFON: Sliding roof is down
OFF: Sliding roof is up±
IG (DIRCT)Ignition SW (Direct
signal)/ON or OFFON: Ignition switch to on
OFF: Ignition switch to off±
IG (MPX)Ignition SW (MPX)/ON
or OFFON: Ignition switch to on
OFF: Ignition switch to off±
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relay, VSV, actuator and so on to oper-
ate without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the meth-
od to shorten the labor time.
It is possible to display the DATA LIST during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on tester, perform the ºACTIVE TESTº.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.

± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1669
1863 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
If not using the hand±held tester, start from STEP 2.
1 Perform active test.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn ignition switch ON and hand±held tester main switch ON.
(c) Select the ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºSliding roof motorº operates as the hand±held tester directs.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.
NOTICE:
Caution is necessary for a part of body not to be caught in as the jam protection system does not
operate during conducting ACTIVE TEST.
HINT:
With one ACTIVE direction, the sliding roof can be slid and tilted continuously.
OK:
The slide roof operates normally.
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1664).
NG

DI±1672
± DIAGNOSTICSSLIDING ROOF SYSTEM
1866 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
If not using the hand±held tester, start from STEP 2.
1 Check sliding roof control switch operation.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn ignition switch ON and hand±held tester main switch ON.
(c) Select the DATA LIST mode on the hand±held tester.
CHECK:
Check that switch status (ON/OFF) changes on the screen of the hand±held tester as the sliding roof control
switch of the vehicle is turned.
SLIDE ROOF:
ItemMeasurement Item/
Display (Range)Normal conditionDiagnostic Note
OPEN SWSliding roof open SW
signal/ON or OFFON: Sliding roof is open
OFF: Sliding roof is close±
CLOSE SWSliding roof close SW
signal/ON or OFFON: Sliding roof is close
OFF: Sliding roof is open±
UP SWSliding roof up SW sig-
nal/ON or OFFON: Sliding roof is up
OFF: Sliding roof is down±
DOWN SWSliding roof down SW
signal/ON or OFFON: Sliding roof is down
OFF: Sliding roof is up±
OK:
The switch status changes in response to the vehicle switch operation.
NG Replace sliding roof control switch or overhead
module.
OK