2001 TOYOTA SEQUOIA DLC3 Ts

Limit
Switch
No. 1 Sliding
Roof
Status
Fully
Opened
SlidingFully
ClosedTilting
Limit
Switch
No. 2250 mm point from fully
opened position
About 10 mm
± DIAGNOSTICSSLIDING ROOF SYSTEM
DI±1675
1869 Author: Date:
2005 SEQUOIA (RM1146U)
Sliding Roof Pulse Plate Circuit
WIRING DIAGRAM
See page DI±1668.
INSPECTION PROCEDURE
HINT:
If not using the hand±held tester, start from STEP 3.
1 Check sliding roof pulse plate operation.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn ignition switch ON and hand±held tester main switch ON.
(c) Select the DATA LIST mode on the hand±held tester.
CHECK:
(a) Operate the sliding roof.
(b) At this time, check that status (ON/OFF) of limit switch 1 and limit switch 2 changes on the hand±held
tester screen as shown in the chart below.
SLIDE ROOF:
ItemMeasurement Item/
Display (Range)Normal conditionDiagnostic Note
LIMIT SW 1Position SW NO.1/
ON or OFFON: 250 mm point from fully opened position
OFF: Sliding roof fully closed position±
LIMIT SW 2Position SW NO.2/
ON or OFFON: Sliding roof fully closed position
OFF: Sliding roof except fully closed position±
OK:
NG Replace sliding roof gear assembly.
OK
DI279±11

DI±1676
± DIAGNOSTICSSLIDING ROOF SYSTEM
1870 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check sliding roof motor status.
PREPARATION:
Connect the hand±held tester to the DLC3.
(a) Enter into ACTIVE TEST mode of hand±held tester.
CHECK:
(a) Check that ºSliding roof motorº operates as the hand±held tester directs.
(b) At this time, check that motor status changes on the screen of the hand±held tester as the sliding roof
switch of the vehicle is turned.
SLIDE ROOF:
ItemTest DetailsDiagnostic Note
SLIDE ROOFSliding roof CLOS/UP ± OPN/DWNDuring this ACTIVE TEST, jam protection caught
detection can be monitored.
NOTICE:
Caution is necessary for a part of body not to be caught in as the jam protection system does not
operate during conducting ACTIVE TEST.
OK:
The motor operates normally.
NG Replace sliding roof gear assembly.
OK
Go to step NO TAG.

I28734
BODY ECU
Back Door
Power Window SW
Rear Wiper
and
Washer
Switch
Rear Washer
Motor
Theft Deterrent Horn
Light
Control
Sensor
Wireless
Door Lock
Receiver ECU±B From
Battery
DLC3From
Battery
POWER MAIN
Power
Window SW
(RR)Power
Window
Motor (RR)PWR
No. 3
PWR
No. 2
Power
Window SW
(RL)Power
Window
Motor (RL)
From
Battery
From
Battery DOME
HORN Interior Light
HORN
Vehicle Horn
Combination Meter
Security Indicator
Horn Switch
Glass
Breakage
Sensor ECUWireless Buzzer
ECU±B
HTR PWS
BUP
BDN
RWLS
RWC1
RWW
SHTRCY
RRU
RRD
RLU
RLD
ILE
CLTB
CLTS
CLTEHR
RDA
PRG
GND1IND
HORN
BZR
OBD2DOP
Microphone
From
Battery
± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1681
1875 Author: Date:
2005 SEQUOIA (RM1146U)

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1691
1885 Author: Date:
2005 SEQUOIA (RM1146U) TAIL ± GND1
(B6±7 ± B6±6)
G ± W±BLight control switch
(TAIL)Light control switch OFF10 to 14 V
CLTS (*3) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control
sensor (Signal)Ignition switch OFFBelow 1 V
CLTS (*3) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control
sensor (Signal)Ignition switch ONSignal waveform
CLTE (*3) ± GND1
(B6±3 ± B6±6)BR ± W±BAutomatic light control
sensor (Ground)AlwaysBelow 1 V
CLTB (*3) ± GND1
(B6±4 ± B6±6)R±G ± W±BAutomatic light control
sensor (IG)Ignition switch OFFBelow 1 V
CLTB (*3) ± GND1
(B6±4 ± B6±6)R±G ± W±BAutomatic light control
sensor (IG)Ignition switch ON10 to 14 V
BZR ± GND1
(B7±15 ± B6±6)LG ± W±BWireless door lock
buzzer signalBuzzer does not soundBelow 1 V
BZR ± GND1
(B7±15 ± B6±6)LG ± W±BWireless door lock
buzzer signalBuzzer sounds10 to 14 V
RLD ± GND1
(B7±26 ± B6±6)L ± W±BPower window control
(Rear LH (DOWN))Ignition switch ONBelow 1 V
RLD ± GND1
(B7±26 ± B6±6)L ± W±BPower window control
(Rear LH (DOWN))Ignition switch ON,
Rear left power window DOWN
operation
10 to 14 V
RLU ± GND1
(B7±25 ± B6±6)G±R ± W±BPower window control
(Rear LH (UP))Ignition switch ONBelow 1 V
RLU ± GND1
(B7±25 ± B6±6)G±R ± W±BPower window control
(Rear LH (UP))Ignition switch ON,
Rear left power window UP op-
eration
10 to 14 V
RRD ± GND1
(B5±20 ± B6±6)L ± W±BPower window control
(Rear RH (DOWN))Ignition switch ONBelow 1 V
RRD ± GND1
(B5±20 ± B6±6)L ± W±BPower window control
(Rear RH (DOWN))Ignition switch ON,
Rear right power window DOWN
operation
10 to 14 V
RRU ± GND1
(B5±19 ± B6±6)G±Y ± W±BPower window control
(Rear RH (UP))Ignition switch ONBelow 1 V
RRU ± GND1
(B5±19 ± B6±6)G±Y ± W±BPower window control
(Rear RH (UP))Ignition switch ON,
Rear right power window UP op-
eration
10 to 14 V
HEAD ± GND1
(B6±9 ± B6±6)G±Y ± W±BLight control switch
(HEAD)Light control switch HEADBelow 1 V
HEAD ± GND1
(B6±9 ± B6±6)G±Y ± W±BLight control switch
(HEAD)Light control switch OFF or TAIL10 to 14 V
PKB ± GND1
(B5±3 ± B6±6)LG±R ± W±BParking brake switch
signalIgnition switch ON, Parking brake
appliedBelow 1 V
PKB ± GND1
(B5±3 ± B6±6)LG±R ± W±BParking brake switch
signalIgnition switch ON, Parking brake
not applied10 to 14 V
GSWGR RAirbag sensor commu-Airbag sensor communicationGSW
(B6±16)GR±RAirbag sensor commu
nication signal
Airbag sensor communication
circuit±
OBD2
(B5±2)G±RDiagnosis signalDLC3 communication circuit±
FFOG ± GND1
(B6±13 ± B6±6)G±B ± W±BFog light switch signalHeadlight dimmer switch LOW,
Fog light switch OFFBelow 1 V

DID99±01
DI±1694
± DIAGNOSTICSBODY CONTROL SYSTEM
1888 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
According to the DATA LIST displayed by the hand±held tester, you can read the values of the switches,
sensors, actuators and so on without parts removal. Reading the DATA LIST as a first step of troubleshooting
is one of the methods to shorten labor time.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on the tester, read the ºDATA LISTº.
BODY ECU:
ItemMeasurement Item/Display
(Range)Normal ConditionDiagnostic Note
KEY UNLK WRN SWKey unlock warning switch/ON or
OFFON: Key is in ignition key cylinder
OFF: No key is in ignition key cyl-
inder
±
ACC SWACC switch/ON or OFFON: Ignition switch ACC
OFF: Ignition switch OFF±
IG SWIG switch/ON or OFFON: Ignition switch ON
OFF: Ignition switch OFF±
PARKING BRAKE SWParking brake switch/ON or OFF
ON:
Parking brake pedal depressed
(ON)
OFF:
Parking brake released (OFF)
±
HOOD COURTSY SWHood courtesy switch/ON or OFF
ON: Engine hood OPEN
(Hood courtesy switch ON)
OFF: Engine hood CLOSED
(Hood courtesy switch OFF)
±
D DOR CTY SWDriver door courtesy light switch/
ON or OFFON: Driver door is opened
OFF: Driver door is closed±
P DOR CTY SWFront passenger door courtesy
light switch/ON or OFF
ON: Front passenger door is
opened
OFF: Front passenger door is
closed
±
Rr DOR CTY SWRear passenger door courtesy
light switch/ON or OFF
ON: Rear passenger door is
opened
OFF: Rear passenger door is
closed
±
MIRR SEL SW RRemote control mirror switch pas-
senger side/ON or OFF
ON: Remote control mirror switch
passenger side is selected
OFF: Remote control mirror switch
passenger side is not selected
±
MIRR SEL SW LRemote control mirror switch driv-
er side/ON or OFF
ON: Remote control mirror switch
driver side is selected
OFF: Remote control mirror switch
driver side is not selected
±
MIRR POS SW RRemote control mirror switch R
position/ON or OFF
ON: Remote control mirror switch
R position is selected
OFF: Remote control mirror switch
R position is not selected
±

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1697
1891 Author: Date:
2005 SEQUOIA (RM1146U)DISP EX ON SEN
Display extinction luminous inten-
sity/NORMAL, DARK2, DARK1,
LIGHT1 or LIGHT2Customized condition will be dis-
played±
DISP EX OFF SEN
Display extinction release lumi-
nous intensity/NORMAL, DARK2,
DARK1, LIGHT1 or LIGHT2Customized condition will be dis-
played±
2. ACTIVE TEST
HINT:
Performing the ACTIVE TEST using the hand±held tester allows the relays, actuators and so on to operate
without parts removal. Performing the ACTIVE TEST as a first step of troubleshooting is one of the methods
to shorten labor time.
It is possible to display the DATE LIST during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) According to the display on the tester, perform the ºACTIVE TESTº.
BODY ECU:
ItemTest DetailsDiagnostic Note
SECURITY INDICTurn security indicator light ON/OFF±
SECURITY HORNTurn theft horn ON/OFFThis test is available only for vehicles equipped
with security horn.
BUZZ CONT SOUNDWireless buzzer continuous sound ON/OFF±
BUZZ RESP SOUNDTurn wireless buzzer ON/OFFTurn volume to MAX if it is a wireless buzzer
equipped vehicle.
HEAD LIGHTHeadlight relay ON/OFF±
TAIL LIGHTTaillight ON/OFF±
ILLUMI OUTPUTIlluminated entry system ON/OFFIG is ON, E/G is stopped and light control SW is
OFF.
ALL COURTESYDOOR indicator light ON/OFF±
VEHICLE HORNTurn vehicle horn ON/OFF±
RL P/W UP/DOWNRear left passenger power window DOWN/UPCaution: This test causes vehicle parts to move.
Watch your hands and feet.
RR P/W UP/DOWNRear right passenger power window DOWN/UPCaution: This test causes vehicle parts to move.
Watch your hands and feet.
DOOR LOCKDoor lock LOCK/UNLOCKAll doors are closed.

DI94R±07
I28393
Hood Courtesy Switch Engine Room J/B
 ECU±B Fuse
 Door No. 2 Fuse
 H±LP RH Fuse (*2)
 H±LP LH Fuse (*2)
 DRL Fuse (*1)
Rear Washer Motor
Horn
Headlight
Rear washer switch
Ignition Switch
 Key Unlock Switch
DLC3 Body ECU
Instrument Panel J/B
 ECU±IG Fuse
 RAD No. 2 Fuse
 FOG Fuse
 FOG LIGHT Relay
 POWER MAIN Relay
 WSH Fuse
 STOP Fuse
 TAILLIGHT Relay Back Door Power
Window SwitchTheft Horn
Engine Room R/B
No.2
 DIMMER Relay
 DRL No. 4 Relay
 H±LP RH Fuse (*1)
 H±LP LH Fuse (*1)
 H±LP RL Fuse (*1)
 H±LP LL Fuse (*1)
Fog Light
Wireless Door
Control Receiver Wireless Door Lock Buzzer
Combination Meter Memory Seat Switch
(*1): w/ Daytime Running Light
(*2): w/o Daytime Running Light (Located behind
the instrument panel)
(Located behind
the heater control panel)
 DOME Fuse
 HEAD Relay
 HORN Relay
 DOME Fuse
Automatic Light Control Sensor
Stop Light Switch
Remote Control Mirror SwitchGlass Breakage
Sensor Microphone Glass Breakage
Sensor ECU
Combination Switch
 Light Control Switch
 Headlight Dimmer Switch
 Fog Light Switch DI±1698
± DIAGNOSTICSBODY CONTROL SYSTEM
1892 Author: Date:
2005 SEQUOIA (RM1146U)
PARTS LOCATION

± DIAGNOSTICSBODY CONTROL SYSTEM
DI±1707
1901 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
When using the hand±held tester, start the inspection from step 1 and when not using the hand±held tester,
start from step 2.
1 Check TAILLIGHT relay using hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
CHECK:
According to the display on the tester, perform the ºACTIVE TESTº.
BODY ECU:
ItemTest DetailsDiagnostic Note
TAIL LIGHTTaillight ON/OFF±
OK:
The taillights turn on or off correctly when operating them through the hand±held tester.
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1686).
NG
2 Check TAILLIGHT relay (See page BE±27).
NG Replace TAILLIGHT relay.
OK
3 Check wire harness and connector between TAILLIGHT relay and body ECU, bat-
tery and TAILLIGHT relay (See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1686).