2001 TOYOTA SEQUOIA DLC3 Ts

I28464
ECM
Sub J/B No.4
23
E4
1328
T5
15
A205
4E
TC
TC5
4B
5
4C 5
4D
5
4A 15
1F 9
1A
J43
J/C12
T17 P±B P±B Translate ECU
TCP±B
P±B
O
O 4 TC
CG D6
DLC3 Airbag Sensor
Assembly
Instrument Panel J/BTire Pressure
ECU
P±B
G
A A
IGTC
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1567
1761 Author: Date:
2005 SEQUOIA (RM1146U)
Diagnosis circuit
CIRCUIT DESCRIPTION
Making a short circuit between terminals TC and CG of the DLC3 will output DTCs from the DLC3.
WIRING DIAGRAM
HINT:
When a particular warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an
internal ground short in the relevant ECU is suspected.
DIDF5±01

I28460
E4
TC
ECM Wire Harness View:
C00083
TCD6DLC3:
DI±1568
± DIAGNOSTICSCRUISE CONTROL SYSTEM
1762 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check harness and connector (TC of DLC3 ± ECM).
PREPARATION:
Disconnect the E4 connector from the ECM.
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Symbol
(Tester connection)ConditionSpecified condition
TC (E4±23) ± TC (D6±13)AlwaysBelow 1 W
NG Repair or replace harness or connector.
OK

C00083CG
D6DLC3:
C00083
TCDLC3:
D6
± DIAGNOSTICSCRUISE CONTROL SYSTEM
DI±1569
1763 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check harness and connector (CG of DLC3 ± Body ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Symbol
(Tester connection)ConditionSpecified condition
CG (D6±4) ± Body groundAlwaysBelow 1 W
NG Repair or replace harness or connector.
OK
3 Check harness and connector (TC of DLC3 ± Body ground).
CHECK:
Measure the resistance according to the value(s) in the table
below.
OK:
Symbol
(Tester connection)ConditionSpecified condition
TC (D6±13) ± Body
groundAlways10 kW or higher
NG Repair or replace harness, connector or each
ECU.
OK
Replace ECM (See page IN±35).

DIABB±02
I24389
T16 Transponder Key ECU: DI±1574
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1768 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
Symbols (Terminals No.)Wiring ColorConditionSpecified condition
+B e GND
(T16 ± 1 e T16 ± 14)W±R e OAlways10 to 14 V
IG e GND
(T16 ± 2 e T16 ± 14)B±O e OIgnition switch ON10 to 14 V
D e GNDWLOIgnition switch ON " 10 to 14 V " D e GND
(T16 ± 3 e T16 ± 14)W±L e OIgnition switch ON "
Connect terminals OP3 and CG of DLC310 to 14 V "
Below 2 V
CODE e GND
(T16 ± 4 e T16 ± 14)R±Y e OIgnition switch ON10 to 14 V
RXCK e GND
(T16 ± 5 e T16 ± 14)LG e OIgnition switch ON10 to 14 V
VC12 e AGND
(T16 ± 6 e T16 ± 12)GR±B e GR±LAlways10 to 14 V
IND e GNDLG BO
Security indicator light is on. (It flashes when the immobiliser
ti ti)3 to 6 V " IND e GND
(T16 ± 7 e T16 ± 14)LG±B e Osystem is operating.) "
Security indicator light is off.3 to 6 V "
Below 1 V
CTY e GNDGR LODriver's door closed " 10 to 14 V " CTY e GND
(T16 ± 8 e T16 ± 14)GR±L e ODriver s door closed "
Driver's door open10 to 14 V "
Below 1 V
KSW e GNDYGOKey unlock warning switch ON (Key inserted) " Below 1 V " KSW e GND
(T16 ± 9 e T16 ± 14)Y±G e OKey unlock warning switch ON (Key inserted) "
Key unlock warning switch OFF (Key not inserted)Below 1 V "
10 to 14 V
EFII e GND
(T16 ±10 e T16 ± 14)L±Y e OIgnition switch ON10 to 14 V
EFIO e GND
(T16 ±11 e T16 ± 14)P±G e OIgnition switch ON10 to 14 V
AGND e Body ground
(T16 ±12 e Body
ground)
GR±L e Body groundAlwaysBelow 1 V
TXCT e GND
(T16 ± 13 e T16 ± 14)Y±G e OIgnition switch ON10 to 14 V
GND e Body ground
(T16 ±14 e Body
ground)
O e Body groundAlwaysBelow 1 V

DID50±01
C00083DLC3
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1575
1769 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. DIAGNOSIS SYSTEM
(a) Inspect the battery voltage.
Battery voltage: 11 to 14 V
If voltage is below 11 V, recharge the battery before proceeding.
(b) Check the DLC3.
The transponder key ECU uses ISO 9141±2 for commu-
nication. The terminal arrangement of the DLC3 complies
with SAE J1962 and matches the ISO 9141±2 format.

DID51±01
A04550
CG
OP3
DLC3 12345678
9
1011
13 1516 12 14
TC
I28427
Security Indicator
Light MIL
BR3904
Normal System Code
0.25 Sec.0.25 Sec.
I02680
Diagnostic Trouble Code (Example Code 12, 99)
0.5 Sec. 0.5 Sec.
1.5 Sec. 2.5 Sec.
One Cycle4.5 Sec.Repeat
DI±1576
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1770 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
1. INSPECT DIAGNOSIS
(a) Check the DTC using SST check wire.
(1) Turn the ignition switch ON, but do not start the en-
gine.
(2) When checking DTC 99: Using SST, connect termi-
nals 13 (TC) and 4 (CG) of the DLC3.
(3) When checking codes except DTC 99: Using SST,
connect terminals 8 (OP3) and 4 (CG) of the DLC3.
SST 09843±18040
(4) Read the DTC indicated by the number of times the
security indicator light or the MIL blinks.
HINT:

If no DTC is output, inspect the diagnosis circuits (OP3
and TC) and the security indicator light circuit (See page
DI±1597, DI±1567, DI±1599).

If the system is operating normally, the light blinks twice
per second.

As an example, the blinking patterns of the normal system
code and trouble codes 12 and 99 are shown on the left
and below.

DI3DP±10
I28395
ECM Transponder Key Coil
Transponder Key Amplifier Instrument
Panel J/B

IGN Fuse
Engine Room J/B

ECU±B Fuse

EFI No. 1 Fuse
Transponder Key ECU
Combination Meter

Security Indicator Light

MIL
DLC3
(Located behind the combination meter)
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1579
1773 Author: Date:
2005 SEQUOIA (RM1146U)
PARTS LOCATION

I24837
IGTransponder Key ECU
D 3
T16
OJ43
J/C W±L
8 OP3 D6
DLC3
CG
4A
AO
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
DI±1599
1793 Author: Date:
2005 SEQUOIA (RM1146U)
Diagnosis Circuit
CIRCUIT DESCRIPTION
This circuit sends a signal to the ECU that outputs DTCs.
WIRING DIAGRAM
DIABK±03