2001 TOYOTA SEQUOIA DLC3 Ts

A04550
CGOP3
1 234 5 678
91011 13 151612 14
DI±1600
± DIAGNOSTICSENGINE IMMOBILISER SYSTEM
1794 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check voltage between terminals OP3 and CG of DLC3.
PREPARATION:
Turn the ignition switch ON.
CHECK:
Measure the voltage between terminals OP3 and CG of the
DLC3.
OK:
Voltage: 10 to 14 V
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1573).
NG
2 Check harness and connector between transponder key ECU and DLC3, DLC3
and body ground (See page IN±35).
NG Repair or replace harness or connector.
OK
Replace transponder key ECU
(See page IN±35).

DID8W±01
C00083DLC3
± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1625
1819 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
INSPECT THE DLC3
The vehicle's combination meter ECU uses ISO 9141±2 for
communication. The terminal arrangement of the DLC3 com-
plies with SAE J1962 and matches the ISO 9141±2 format.
Tester connectionConditionSpecified condition
7 (Bus
Line) ± 5 (Signal ground)During communicationPulse generation
4 (Chassis Ground) ± BodyAlwaysBelow 1 W
5 (Signal Ground) ± BodyAlwaysBelow 1 W
16 (B+) ± BodyAlways10 to 14 V
HINT:
If the display shows UNABLE TO CONNECT TO VEHICLE
when you have connected the cable of the hand±held tester to
the DLC3, turned the ignition switch to the ON position and op-
erated the tester, there is a problem either on the vehicle side
or tester side.

If communication is normal when the tool is connected to
another vehicle, inspect the DLC3 on the original vehicle.

If communication is still impossible when the tool is con-
nected to another vehicle, the problem is probably in the
tool itself, so consult the Service Department listed in the
tool's instruction manual.

DID8X±01
DI±1626
± DIAGNOSTICSCOMBINATION METER SYSTEM
1820 Author: Date:
2005 SEQUOIA (RM1146U)
DATA LIST / ACTIVE TEST
DATA LIST
According to the DATA LIST displayed by the hand±held tester, you can read the values of the switches,
sensors, actuators and so on without part removal. Reading the DATA LIST as the first step of troubleshoot-
ing is one method to shorten labor time.
(a) Warm up the engine.
(b) Turn the ignition switch off.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
SPEED METER
Vehicle Speed Meter /
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Almost the same as actual vehicle
speed (When driving)
TACHO METEREngine RPM /
Min.: 0 rpm Max.: 12,750 rpmAlmost the same as actual engine
speed (When engine is running)
FUEL GAUGEFuel Input /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the fuel receiver gauge
angle.

LIGHT RHEOSTATLight Control Rheostat /
Min.: 0 Max.: 255Light control rheostat switch is
Dark (0) " Bright (255)
OIL GAUGEOil Gauge /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the oil pressure receiver
gauge angle.

ODO/TRIP SWODO / TRIP
ODO/TRIP switch / ON/OFFON: Switch is pushed
OFF: Switch is released

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1627
1821 Author: Date:
2005 SEQUOIA (RM1146U)
ACTIVE TEST
Performing the ACTIVE TEST using the hand±held tester allows the meters, indicators and so on to operate
without part removal. Performing the ACTIVE TEST as the first step of troubleshooting is one way to shorten
labor time.
It is possible to display the DATA LIST on the hand±held tester during the ACTIVE TEST.
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SPEED METER
Operate speedometer: 0 / 40 (24) / 80 (48) / 120
(72) / 160 (96) /
200 (120) km/h (mph)The needle position should be within the accept-
able tolerance
TACHOMETER
Operate tachometer:
0 rpm / 1,000 rpm / 2,000 rpm / 3,000 rpm /
4,000 rpm / 5,000 rpm / 6,000 rpm / 7,000 rpmConfirm that the vehicle is stopped and engine is
idling.
FUEL GAUGEOperate fuel gauge: EMPTY, 1/2, FULLConfirm that the vehicle is stopped and engine is
idling.
COOLANT TEMPOperate engine coolant temperature receiver
gauge: HIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
D BELT REMINDOperate driver's seat belt warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
OPEN DOOR WARNOperate open door warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
LOW FUEL WARNOperate fuel level warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
TAILLIGHT INDICOperate taillight indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
HEADLIGHT INDICOperate Hi±beam indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SRS WARNOperate SRS warning light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
ODO/TRIP DISPOperate ODO/TRIP display: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
KEY REMND BUZZROperate key reminder buzzer: OFF / ONConfirm that the vehicle is stopped and engine is
idling.
SEAT BELT BUZZROperate driver's seat belt warning buzzer:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
MAINT REQDOperate oil maintenance indicator light:
OFF / ONConfirm that the vehicle is stopped and engine is
idling.
VOLT METEROperate volt meter: 9 V / 12 V / 15 V / 18VConfirm that the vehicle is stopped and engine is
idling.
OIL PRESS METEROperate oil pressure meter: HIGH, 3/4, 1/2, 1/4,
LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1633
1827 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
SPEED METER0 / 40 (24) / 80 (48) / 120 (72) / 160 (96) /
200 (120) km/h (mph)The needle position should be within the accept-
able tolerance.
OK:
Speedometer readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item/
Range (Display)Normal ConditionDiagnostic Note
SPEED METER
Vehicle Speedometer /
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)Almost the same as actual vehicle
speed (When driving)
OK:
Vehicle speed displayed on the tester is almost the same as the actual vehicle speed.
OK Replace combination meter
(See page IN±35).
NG

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1637
1831 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
TACHOMETER0 rpm / 1,000 rpm / 2,000 rpm / 3,000 rpm / 4,000
rpm / 5,000 rpm / 6,000 rpm / 7,000 rpmConfirm that the vehicle is stopped and engine is
idling.
OK:
Tachometer readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±35).
OK
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item/
Range (Display)Normal ConditionDiagnostic Note
TACHO METEREngine RPM /
Min.: 0 rpm Max.: 12,750 rpmAlmost the same as actual engine
speed (When engine is running)
OK:
Engine speed displayed on the tester is almost the same as the actual engine speed.
OK Replace combination meter
(See page IN±35).
NG

± DIAGNOSTICSCOMBINATION METER SYSTEM
DI±1641
1835 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 3 when not using the
hand±held tester.
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
FUEL GAUGEEMPTY, 1/2, FULLConfirm that the vehicle is stopped and engine is
idling.
OK:
Fuel receiver gauge readings change according to hand±held tester operation.
NG Replace combination meter
(See page IN±24).
OK
2 Read value of hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
Operate the hand±held tester according to the steps on the display and select ºDATA LISTº.
METER:
ItemMeasurement Item /
Range (Display)Normal ConditionDiagnostic Note
FUEL GAUGEFuel Input /
Min.: 0 Max.: 255Tester indication changes accord-
ing to the fuel receiver gauge
angle.

OK:
Fuel value signal displayed on the tester is almost the same as the needle indication.
NG Replace combination meter
(See page IN±24).
OK

DI±1644
± DIAGNOSTICSCOMBINATION METER SYSTEM
1838 Author: Date:
2005 SEQUOIA (RM1146U)
Malfunction in engine coolant temperature receiver gauge
CIRCUIT DESCRIPTION
The ECM receives an engine coolant temperature signal from the engine coolant temperature sensor and
sends it to the A/C ECU.
The combination meter receives the signal from the A/C ECU through multiplex communication. Therefore,
if a malfunction occurs in the engine coolant temperature receiver gauge, there may be a malfunction in the
multiplex communication system, air conditioning system, or engine system.
(Multiplex communication system: See page DI±1892)
(Air conditioning system: See page DI±2301)
(Engine system: See page DI±9)
INSPECTION PROCEDURE
1 Perform active test by hand±held tester.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
CHECK:
From the display on the tester, perform the ºACTIVE TESTº.
METER:
ItemTest DetailsDiagnostic Note
COOLANT TEMPHIGH / NORMAL / LOW (OFF)Confirm that the vehicle is stopped and engine is
idling.
OK:
Engine coolant temperature receiver gauge readings change according to hand±held tester op-
eration.
OK Go to engine system or air conditioning system
(See page DI±9 or DI±2301).
NG
Replace combination meter
(See page IN±35).
DID92±01