2001 TOYOTA SEQUOIA TS pin

H24861
H24321
Hog Ring
H24318Hog Ring
H24319
H24320
BO±114
± BODYFRONT SEAT (Power Adjuster Type)
3667 Author: Date:
2005 SEQUOIA (RM1146U)
(c) w/ Side airbag:
Remove the nut and disconnect the seatback cover
bracket from the seat frame assembly.
(d) Remove the hog rings from the seat frame assembly.
(e) Remove the hog rings from the seat frame assembly.
(f) Remove the seatback cover and pad from the seat frame
assembly.
9. REMOVE SEATBACK COVER
(a) Turn up the seatback cover and remove the hog rings.
(b) Remove the 2 headrest supports.
(c) Remove the seatback cover from the seatback pad.
10. w/ Seat heater:
REMOVE SEATBACK HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seatback heater assembly from the seatback cover.
11. REMOVE SEAT CUSHION COVER AND PAD
(a) Disconnect the wire harness clamp.
(b) Remove the 2 clips.

H24378
H24395
H24324
H24325
H24326
± BODYFRONT SEAT (Power Adjuster Type)
BO±115
3668 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Remove the hog rings from the seat cushion cover.
(d) Unlatch the seat cushion cover hooks, then remove the
seat cushion cover and seat cushion pad.
12. REMOVE SEAT CUSHION COVER
Remove the hog rings and seat cushion cover from the seat
cushion pad.
13. w/ Seat heater:
REMOVE SEAT CUSHION HEATER ASSEMBLY
Cut off the tack pins which fasten the seat heater, and then re-
move the seat cushion heater assembly from the seat cushion
cover.
14. REMOVE LUMBAR SUPPORT ADJUSTER
(a) Disconnect the connector.
(b) Disengage the seatback spring edge from the seat frame
assembly.
NOTICE:
Be careful when releasing the seatback spring edge, be-
cause there is a possibility that the spring may break due
to tension by the lumbar support.
(c) Remove the 2 screws and lumbar support adjuster.
(d) Remove the bushing from the lumbar support adjuster.
15. REMOVE RH AND LH RECLINING ADJUSTER INSIDE
COVERS
(a) Remove the screw and RH reclining adjuster inside cover.
(b) Disconnect the wire harness clamp.
(c) Perform the same procedure on the other side.

H24324
H24394
Listing Pocket
Seat WireSeat Heater
Tack Pin
Seat Cushion Cover
A: Install the tack pins under the wire.A
Seat Heater Strap
Tack pins should not be beyond the seat.Front
Name Stamp a±a:
Tack Pin
Seat Heater
b±b:
Tack PinSeat Heater
Seat Cushion Cover
Tack Pin
ab
ab
a
a bb
bb
bb
bbbb b
b bb
H24395
BO±118
± BODYFRONT SEAT (Power Adjuster Type)
3671 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Engage the seatback spring edge with the seat frame as-
sembly.
6. w/ Seat heater:
INSTALL SEAT CUSHION HEATER ASSEMBLY
(a) Set the seat cushion heater assembly with the name
stamp side facing the seat cushion cover.
(b) Install the seat cushion heater assembly with the 10 tack
pins.
NOTICE:
Do not substitute other metal parts for tack pins.
7. INSTALL SEAT CUSHION COVER
Install the seat cushion cover to the seat cushion pad with the
hog rings.
HINT:
When installing the hog rings, take as much care as possible to
prevent wrinkles.
8. INSTALL SEAT CUSHION COVER AND PAD
(a) Install the seat cushion cover with seat cushion pad, and
latch the seat cushion cover hooks.

H24378
H24320
H24393
Listing Pocket
Seat WireSeat Heater
Tack Pin
Seatback Cover
A: Install the tack pins under the wire.A
Tack pins should not be beyond the seat.Upper
Name Stamp a±a:
Tack Pin
Seat Heater
b±b:
Tack Pin
Seat Heater
Tack Pina
ba
b
Seatback Coveraa
bb
b
bb bb
b
b b
bb
b
bbb
± BODYFRONT SEAT (Power Adjuster Type)
BO±119
3672 Author: Date:
2005 SEQUOIA (RM1146U)
(b) Install the hog rings to the seat cushion cover.
(c) Install the 2 clips.
(d) Connect the wire harness clamp.
9. w/ Seat heater:
INSTALL SEATBACK HEATER ASSEMBLY
(a) Set the seatback heater assembly with the name stamp
side facing the seatback cover.
(b) Install the seatback heater assembly with the 11 tack
pins.
NOTICE:
Do not substitute other metal parts for tack pins.
10. INSTALL SEATBACK COVER
(a) Install the seatback cover to the seatback pad.
(b) Install the 2 headrest supports.

H17261
Hexagon
Bolt
H23461
BO±138
± BODYREAR NO.1 SEAT (Separate Type)
3691 Author: Date:
2005 SEQUOIA (RM1146U)
6. REMOVE REAR SEAT CUSHION UNDER COVER
(a) Using a 5 mm hexagon wrench, remove the bolt and
cushion.
(b) Remove the 6 screws and rear seat cushion under cover.
(c) Remove the screw and fold seat stopper band.
7. REMOVE FOLD SEAT LOCK CONTROL CABLE NO. 1
Using a screwdriver, remove the fold seat lock control cable No.
1.
HINT:
Tape the screwdriver tip before use.
8. REMOVE LH REAR SEAT RECLINING ADJUSTER
AND LH REAR SEAT LOCK
(a) Unfasten the bolt, then remove the rear No. 1 seat inner
belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(b) Remove the 2 nuts and LH rear seat reclining adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(c) Remove the bolt and LH rear seat lock.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
9. REMOVE RECLINING CONNECTING PIPE
10. REMOVE RH REAR SEAT RECLINING ADJUSTER
Remove the 2 nuts and RH rear seat reclining adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
11. REMOVE SEAT CUSHION COVER
(a) Remove the seat cushion cover with pad from the seat
cushion frame.
(b) Remove the seat cushion cover from the seat cushion
pad.
HINT:
At the time of reassembly, take as much care as possible to
minimize wrinkles when installing hog rings.
12. REMOVE REAR SEAT CUSHION HINGE LH
(a) Using a screwdriver, remove the E±ring.
(b) Remove the pin, bushings, spring, collar and rear seat
cushion hinge.
(c) Remove the rear seat cushion hinge on the other side us-
ing the same procedures (a) and (b) described above.
13. REMOVE RH REAR SEAT LOCK
Remove the 2 bolts and RH rear seat lock.
Torque: 64 N´m (653 kgf´cm, 47 ft´lbf)

H16765
H16766
H07940
BO±146
± BODYREAR NO.1 SEAT (Split Type LH)
3699 Author: Date:
2005 SEQUOIA (RM1146U)
10. REMOVE REAR SEAT OUTER BELT
(a) Remove the 2 bolts and rear seat shoulder belt guide.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
HINT:
At the time of reassembly, please refer to the following item.
Install the shoulder belt guide to the seatback frame with a sit
the guide facing to the rear side of the vehicle.
(b) Remove the nut, 3 clamps and rear seat outer belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
11. REMOVE SEATBACK COVER
Remove the hog rings and seatback cover.
HINT:
At the time of reassembly, please refer to the following item.
When instaling hog rings, take care to prevent wrinkles as little
as possible.
12. REMOVE SEAT CUSHION FRAME
Remove the hog rings and seat cushion frame.
HINT:
At the time of reassembly, please refer to the following item.
When instaling hog rings, take care to prevent wrinkles as little
as possible.
13. REMOVE REAR NO. 1 SEAT ADJUSTER
(a) Remove the 2 bolts and rear No. 1 seat outer adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(b) Remove the 2 bolts and rear No. 1 seat inner adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
(c) Remove the 4 screws and 2 hinges covers from the rear
No. 1 seat outer and inner adjusters.
(d) Remove the 2 screws and 2 reclining inner covers from
the rear No. 1 seat outer and inner adjuster.
14. REMOVE REAR SEAT STAY
Remove the 2 bolts and rear seat stay.
15. REMOVE REAR SEAT CUSHION HINGE
(a) Using a screwdriver, remove the spring nut and E±rings.
(b) Remove the 2 hinge pins, 2 cushion spacers, 2 cushion
support springs and 2 rear seat cushion hinges.
16. REMOVE LH REAR SEAT LOCK
Unfasten the bolt, then remove the inner belt and LH rear seat
lock.
17. REMOVE RH REAR SEAT LOCK
(a) Remove the screw and rear seat lock cover.
(b) Remove the bolt, seat belt anchor and inner belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(c) Remove the RH rear seat lock.

H17262
BO±152
± BODYREAR NO.1 SEAT (Split Type RH)
3705 Author: Date:
2005 SEQUOIA (RM1146U)
7. REMOVE LH REAR SEAT RECLINING ADJUSTER
AND REAR SEAT LOCK
(a) Unfasten the bolt, then remove the rear No. 1 seat inner
belt.
Torque: 42 N´m (430 kgf´cm, 31 ft´lbf)
(b) Remove the bolt, 2 nut and LH rear seat reclining adjuster
with rear seat lock.
Torque:
bolt: 43 N´m (440 kgf´cm, 32 ft´lbf)
nut: 43 N´m (440 kgf´cm, 32 ft´lbf)
(c) Using a screwdriver, remove the E±ring, then remove the
LH rear seat reclining adjuster from the rear seat lock.
8. REMOVE RECLINING CONNECTING PIPE
9. REMOVE RH REAR SEAT RECLINING ADJUSTER
Remove the 2 nuts and RH rear seat reclining adjuster.
Torque: 43 N´m (440 kgf´cm, 32 ft´lbf)
10. REMOVE SEAT CUSHION COVER
(a) Remove the seat cushion cover with pad from the seat
cushion frame.
(b) Remove the seat cushion cover from the seat cushion
pad.
11. REMOVE REAR SEAT CUSHION HINGE
(a) Using a screwdriver, remove the E±ring.
(b) Remove the pin, bushings, spring, collar and rear seat
cushion hinge.
(c) Employ the same manner described above to the other
side.

BO4SP±01
± BODYREAR NO.1 SEAT (Split Type RH)
BO±153
3706 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
INSPECT RECLINING LOCK POSITION SLIPPING OFF
When reclining the seat, inspect that the RH and LH rear seat reclining adjusters are released at the same
time.
HINT:
When the reclining lock position slips off, disassemble the seat to adjust the position.