2001 TOYOTA SEQUOIA terminals of DLC3

B17411
E4
AIRVAIRP
± DIAGNOSTICSENGINE
DI±435
629 Author: Date:
2005 SEQUOIA (RM1146U)
8 Check voltage between AIRP and AIRV terminal of ECM and body ground.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON and turn the tester ON.
CHECK:
(a) When the air pump and air switching valve are operated
using the hand±held tester, measure the voltage between
terminals E4±25 (AIRP) and E4±4 (AIRV) of the air injec-
tion driver connector and body ground.
(b) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/AIR INJ CHECK/
MANUAL OPERATION/OPERATION 1 and 2
HINT:
OPERATION 1: AP:OFF, EASV:CLOSE, ASV1:CLOSE,
ASV2:CLOSE
OPERATION 2: AP: ON, EASV:OPEN, ASV1:OPEN,
ASV2:OPEN
NOTICE:
This test only allows technicians to operate the AI system
for 5 seconds. Furthermore, the test can be performed 4
times a trip. If the test is repeated, intervals of at least 30
seconds are required between tests.
While the AI system operation using the hand±held tester
is prohibited, the tester displays the prohibition (WAIT or
ERROR). If the ERROR (AI STATUS NG) is displayed on the
tester, stop the engine for 10 minutes and then try again..
OK:
Standard:
Air pump operationTester ConnectionSpecified Condition
ONE4±25 (AIRP) ±
Body ground10 V or more
OFFE4±25 (AIRP) ±
Body ground3.5 to 7.7 V*
ASV operation (EASV)Tester ConnectionSpecified Condition
OPENE4±4 (AIRV) ±
Body ground10 V or more
CLOSEE4±4 (AIRV) ±
Body ground3.5 to 7.7 V*
*: 35 to 55 % of the +B voltage.
NG Replace ECM (See page SF±80).
OK

B17444
Wire Harness Side:
Air Injection Driver Connector
A41
SIPSIV
DI±436
± DIAGNOSTICSENGINE
630 Author: Date:
2005 SEQUOIA (RM1146U)
9 Check voltage between SIV and SIP terminals of air injection driver and body
ground.
PREPARATION:
(a) Disconnect the A41 air injection driver connector.
(b) Connect the hand±held tester to the DLC3.
(c) Turn the ignition switch ON and turn the tester ON.
CHECK:
(a) When the air pump and air switching valve are operated
using the hand±held tester, measure the voltage between
terminals A41±3 (SIV) and A41±4 (SIP) of the air injection
driver connector and body ground.
(b) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/AIR INJ CHECK/
MANUAL OPERATION/OPERATION 1 and 2
HINT:
OPERATION 1: AP:OFF, EASV:CLOSE, ASV1:CLOSE,
ASV2:CLOSE
OPERATION 2: AP:ON, EASV:OPEN, ASV1:OPEN,
ASV2:OPEN
NOTICE:
This test only allows technicians to operate the AI system
for 5 seconds. Furthermore, the test can be performed 4
times a trip. If the test is repeated, intervals of at least 30
seconds are required between tests.
While the AI system operation using the hand±held tester
is prohibited, the tester displays the prohibition (WAIT or
ERROR). If the ERROR (AI STATUS NG) is displayed on the
tester, stop the engine for 10 minutes and then try again..
OK:
Standard:
Air pump operationTester ConnectionSpecified Condition
ONA41±3 (SIP) ± Body
ground10 V or more
OFFA41±3 (SIP) ± Body
ground3.5 to 7.7 V*
ASV operation (EASV)Tester ConnectionSpecified Condition
OPENA41±4 (SIV) ± Body
ground10 V or more
CLOSEA41±4 (SIV) ± Body
ground3.5 to 7.7 V*
*: 35 to 55 % of the +B voltage.
NG Repair or replace harness or connector be-
tween air injection driver and ECM.
OK

B17396
HT +B
AF± AF+ Sensor 1A/F Sensor Component Side:
Front View
DI±456
± DIAGNOSTICSENGINE
650 Author: Date:
2005 SEQUOIA (RM1146U)
1 Check any other DTCs output (in addition to DTC P2A00 or P2A03).
PREPARATION:
(a) Connect a hand±held tester to the DLC3.
(b) Turn the ignition switch to ON and turn the tester ON.
(c) Select the following menu items: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
CHECK:
(a) Read DTCs.
Result:
Display (DTC Output)Proceed To
P2A00 and/or P2A03A
P2A00 and/or P2A03 and other DTCsB
HINT:
If any DTCs other than P2A00 and/or P2A03 are output, troubleshoot those DTCs first.
B Go to DTC chart (See page DI±58).
A
2 Check resistance of air±fuel ratio (A/F) sensor heater.
PREPARATION:
Disconnect the air±fuel ratio (A/F) sensor connector.
CHECK:
Measure resistance between the terminals of the A/F sensor
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
HT (1) ± +B (2)Between 1.8 W and 3.4 W at 20C (68F)
HT (1) ± AF± (4)10 kW or higher
NG Replace air±fuel ratio (A/F) sensor.
OK

B17411
STA(+) E1(±)
STSW(+)E6
DI±504
± DIAGNOSTICSENGINE
698 Author: Date:
2005 SEQUOIA (RM1146U)
2 Connect hand±held tester, and check STA signal.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON, and push the hand±held tester main switch ON.
(c) Enter the following menu: DIAGNOSIS / ENHANCED OBD II / DATA LIST / ALL / STARTER SIG.
CHECK:
Read the STA signal on the hand±held tester while the starter operates.
OK:
Ignition Switch PositionONSTART
STARTER SIGOFFON
NG Go to step 5.
OK
3 Check voltage between terminal STAR, STSW and E1 of ECM connector.
CHECK:
Measure the voltage between the terminals of the E6 ECM con-
nectors, while cranking the engine (ignition switch START posi-
tion).
OK:
Standard:
Tester ConnectionSpecified Condition
STA (E6±11) ± E1 (E6±1)9 to 14 V
STSW (E6±12) ± E1 (E6±1)9 to 14 V
RESULT:
Terminal STARTerminal STSWProceed to
9 to 14 V9 to 14 VA
0 V9 to 14 VB
0 V0 VC
B Replace ECM (See page SF±80).
C Go to step 9.
A

DIDIP±01
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±524
± DIAGNOSTICSAUTOMATIC TRANSMISSION
718 Author: Date:
2005 SEQUOIA (RM1146U)
BASIC INSPECTION
1. CHECK FLUID LEVEL
(a) Using SST, create a short±circuit between terminals TC
and CG of the DLC3.
SST 09843±18040
(b) Start the engine and run at idle.

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height con-
trol switch off.
(c) Slowly move the shift lever through all positions from P to
L, and move it back to the P position.
(d) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or from
D to N, within 1.5 seconds. (Repeat this operation for 6 se-
conds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(e) Return the shift lever to the P position and disconnect ter-
minals TC and CG.
(f) Idle the engine to raise oil temperature.
(g) Lift up the vehicle immediately after the meter indicator
light (ATF temperature warning light) comes on.

The A/T OIL TEMP warning light indicates the ATF
temperature according to the following table.
ATF Temp.Less than optimized
temperatureOptimized temperatureMore than optimized
temperature
A/T OIL TEMP warning lightOFFONBlinking

D14139Overflow Plug
D14140
Refill Plug
12345678
9 10111213141516
D13649
DLC3:
CG
TC
± DIAGNOSTICSAUTOMATIC TRANSMISSION
DI±529
723 Author: Date:
2005 SEQUOIA (RM1146U)
(4) Temporarily install the gasket and overflow plug.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(5) Add the proper amount of ATF through the refill
hole.
NOTICE:
Refill amount differs depending on the related procedures
indicated below.
Related proceduresRefill amount
Removal and installation of oil pan1.7 liters (1.8 us qts, 1.5 lmp.qts)
Removal of transmission valve body
assy4.3 liters (4.5 us qts, 3.8 lmp.qts)
Removal of torque converter assy5.4 liters (5.7 us qts, 4.8 lmp.qts)
(6) Temporarily install the O±ring and refill plug.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(7) Lower down the vehicle.
(8) Using SST, create a short±circuit between terminals
TC and CG of the DLC3.
SST 09843±18040
(9) Start the engine and run at idle.
NOTICE:

The A/C switch must be turned off.

On models with active height control suspension &
adaptive variable suspension, turn the height control
switch off.
(10) Slowly move the shift lever from the P to the 2±L
position.
Return the shift lever to the P position.

D14141
12345678
9 10111213141516
D13649
DLC3:
CG
TC
D13654
DI±532
± DIAGNOSTICSAUTOMATIC TRANSMISSION
726 Author: Date:
2005 SEQUOIA (RM1146U)
(3) Install the overflow plug with a new gasket when the
draining ATF has becomes a trickle.
Torque: 20 NVm (204 kgfVcm, 15 ftVlbf)
(4) Install the refill plug with a new O±ring.
Torque: 39 NVm (400 kgfVcm, 29 ftVlbf)
(5) Lower down the vehicle.
(6) Turn the ignition switch off.
(7) Check for fluid leaks in the transmission.
If there are leaks, it is necessary to repair or replace O±rings,
FIPGs, oil seals, plugs or other related parts.
(d) When adding a minimum amount of fluid: [*4]
(1) Using SST, create a short±circuit between terminals
TC and CG of the DLC3.
SST 09843±18040
(2) Start the engine and run at idle.
NOTICE:
The A/C switch must be turned off.
(3) Slowly move the shift lever from the P to the 2±L
position. Return the shift lever to the P position.
(4) Switch to the fluid temperature detection mode.
Move the shift lever from the N to the D position, or
from D to N, within 1.5 seconds. (Repeat this opera-
tion for 6 seconds or more.)
OK: The A/T OIL TEMP warning light comes on for 2
seconds and then goes off.
(5) Disconnect terminals TC and CG after confirming
the above condition.
(6) Idle the engine to raise the fluid temperature.

DIDCV±01
C00083
DLC3
CG TS
F16800
Height
Control
Manual
Indicator
Lamp
± DIAGNOSTICSAIR SUSPENSION SYSTEM
DI±711
905 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. INPUT SIGNAL CHECK (Using SST check wire)
HINT:

This function checks if signals from the stop light switch
assy and the door courtesy lamp switch, etc. are being in-
put normally to the ECU.

When entering test mode, the suspension control ECU
sets all the test mode DTCs first.
After completing the test mode for each check item, the
test mode DTCs that are determined normal by the sus-
pension control ECU will be erased.
The test mode DTCs for other check items may not be
erased when only a certain signal is inspected.

When the test mode returns back to normal mode, all the
test mode DTCs will be erased.
(a) Procedure for Input Signal Check Mode (Test Mode) us-
ing SST check wire.
SST 09843±18040
(1) Make sure the ignition switch is OFF.
(2) Set each of the check items to the condition shown
under Operation (A) in the test mode table on the
next page.
(3) Using SST, connect terminals TS and CG of the
DLC3.
(4) Turn the ignition switch to the ON position.
(5) Check that the height control manual indicator lamp
is blinking.
HINT:

The height control manual indicator lamp comes on for 2
seconds, then blinks at 0.25 sec. intervals.

If the height control manual indicator light does not blink,
inspect the height control manual indicator lamp circuit
(See page DI±789).