2001 TOYOTA SEQUOIA terminals of DLC3

DIDLZ±01
F09750
DLC3Ts
CG
BR3904
0.13 sec. 0.13 sec.
ON
OFF
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±899
1093 Author: Date:
2005 SEQUOIA (RM1146U)
TEST MODE PROCEDURE
1. When not using the hand±held tester:
SENSOR CHECK (TEST MODE)
NOTICE:
When having replaced the master cylinder pressure, yaw
rate and deceleration sensors and/or the ECU, perform
zero point calibration of the master cylinder pressure, yaw
rate and deceleration sensors (See page DI±897).
HINT:
If the ignition switch is turned from the ON to the ACC or LOCK
position in test mode, test mode DTCs will be erased.
(a) Procedures for test mode:
(1) Turn the ignition switch OFF.
(2) Check that the shift lever is in the P position, and
turn the steering wheel to the neutral position.
(3) Using SST, connect terminals Ts and CG of the
DLC3.
SST 09843±18040
(4) Start the engine.
(5) Check that the ABS and VSC TRAC warning lights
blink.
HINT:
If the ABS and VSC TRAC warning lights do not blink, inspect
the ABS warning light circuit, VSC TRAC warning light circuit
and Ts terminal circuit.
(6) Keep the vehicle in a stationary condition on a level
surface for 4 sec. or more.
ABS warning light circuitDI±1021 or DI±1025
VSC TRAC warning light circuitDI±1027 or DI±1031
Ts terminal circuitDI±1057

F09750
CG TcDLC3
BR3893
Trouble Code (Example Code 72, 76)
ON
OFF
4 sec. 1.5 sec.
Repeat 2.5 sec.
0.5 sec. 0.5 sec. 0.5 sec. 0.5 sec.7726
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±901
1095 Author: Date:
2005 SEQUOIA (RM1146U)
(f) Read the DTC.
(1) Using SST, connect terminals Tc and CG of the
DLC3.
SST 09843±18040
(2) Read the number of blinks of the warning light.
HINT:

See the list of DTC (step 3).

If all sensors are normal, a normal system code is output
(A cycle of 0.25 sec. ON and 0.25 sec. OFF is repeated).

If 2 or more malfunctions are indicated at the same time,
the codes will be displayed in ascending order.
(3) After doing the check, disconnect terminals Ts and
CG, Tc and CG of the DLC3, and turn the ignition
switch OFF.
SST 09843±18040

DIDM1±01
F13444
USA: CANADA:USA: CANADA:2WD: 4WD:
DI±910
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1104 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSIS SYSTEM
1. CHECK WARNING LIGHT
(a) Release the parking brake pedal.
(b) When the ignition switch is turned ON, check that the ABS
warning light, VSC TRAC warning light, VSC OFF (TRAC
OFF) indicator light, BRAKE warning light and SLIP indi-
cator light come on for approx. 3 seconds.
HINT:

When the parking brake is applied or the level of the brake
fluid is low, the BRAKE warning light comes on.

If the indicator check result is not normal, proceed to trou-
bleshooting for the ABS warning light circuit, VSC TRAC
warning light circuit, VSC OFF (TRAC OFF) indicator light
circuit, BRAKE warning light circuit or SLIP indicator light
circuit.
Trouble AreaSee page
ABS warning light circuitDI±1021 or
DI±1025
VSC TRAC warning light circuitDI±1027 or
DI±1031
VSC OFF (TRAC OFF) indicator light circuitDI±1048
BRAKE warning light circuitDI±1033 or
DI±1038
SLIP indicator light circuitDI±1041 or
DI±1045

The DTCs are simultaneously stored in the memory. The
DTCs can be read by connecting the SST between TC
and CG terminals of the DLC3 and observing the blinking
of the ABS and VSC warning lights, or by connecting a
hand±held tester.

This system has a sensor signal check function (TEST
MODE) (See page DI±899).
The DTC can be read by connecting the SST between ter-
minals TS and CG of the DLC3 and observing the blinking
of the ABS and VSC TRAC warning lights, or by connect-
ing a hand±held tester.

DIDM2±01
F09750
CG TcDLC3
R01346
Normal System Code
0.25 sec.
0.25 sec. 2 sec.
ON
OFF
ON
OFF0.5 sec. 0.5 sec.
Codes 11 and 21
4 sec.1.5 sec.
2.5 sec.
Code 11 Code 21
F09750
CG TcDLC3
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±911
1105 Author: Date:
2005 SEQUOIA (RM1146U)
DTC CHECK / CLEAR
USING SST (CHECK WIRE):
1. CHECK DTC
(a) Using SST, connect terminals Tc and CG of the DLC3.
SST 09843±18040
(b) Turn the ignition switch to the ON position.
(c) Read the DTC from the ABS and VSC TRAC warning
lights on the combination meter.
HINT:

If no code appears, inspect the diagnostic circuit, ABS
warning light circuit or VSC TRAC warning light circuit.
Trouble AreaSee page
Tc terminal circuitDI±1055
ABS warning light circuitDI±1021 or
DI±1025
VSC TRAC warning light circuitDI±1027 or
DI±1031

As examples, the blinking patterns for normal system
code and codes 11 and 21 are shown on the left.
(1) Codes are explained in the code table on page
DI±921.
(2) After completing the check, disconnect terminals Tc
and CG of the DLC3, and turn off the display.
If 2 or more trouble codes are identified at the same time, the
DTCs will be displayed in ascending order.
2. CHECK TRANSLATE DTC
HINT:
Once the ignition switch is turned off, all DTCs in the translate
ECU are cleared.
(a) Release the parking brake pedal.
(b) Check the brake fluid level.
(c) Using SST, connect terminals Tc and CG of the DLC3.
SST 09843±18040
(d) Read the DTC of the BRAKE warning light.
NOTICE:
When reading DTCs, be sure to be seated in the driver's
seat and depressing the brake pedal.

F09750
CG TcDLC3
BR3890
D05981
Hand±held
Tester
DLC3
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±913
1107 Author: Date:
2005 SEQUOIA (RM1146U)
USING SST (CHECK WIRE):
4. CLEAR DTC
(a) Using SST, connect terminals Tc and CG of the DLC3.
SST 09843±18040
(b) Turn the ignition switch to the ON position.
(c) Clear the DTC stored in the ECU by depressing the brake
pedal 8 times or more within 5 seconds.
(d) Check that the warning light indicates the normal code.
(e) Remove the SST from the terminals of the DLC3.
SST 09843±18040
HINT:
Cancellation cannot be done by removing the battery cable or
ECU±IG fuse.
USING HAND±HELD TESTER:
5. CLEAR DTC
(a) Hook up the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position.
(c) Operate the hand±held tester to erase the codes.
HINT:
(d) Please refer to the hand±held tester operator's manual
for further details.

± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1021
1215 Author: Date:
2005 SEQUOIA (RM1146U)
ABS Warning Light Circuit (Remains ON)
CIRCUIT DESCRIPTION
If the ECU detects trouble, it turns on the ABS warning light and prohibits ABS control. At this time, the ECU
records a DTC in memory.
Connect terminals Tc and CG of the DLC3 to make the ABS warning light blink and indicate the DTC.
DI944±04

F13991
GNDCSW*1
Center Integration Panel Assembly
CSW
*2
C3C6
DI±1050
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
1244 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
HINT:
Start the inspection from step 1 when using the hand±held tester and start from step 2 when not using the
hand±held tester.
1 Check operation of the VSC OFF (TRAC OFF) indicator light.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch to the ON position and push the hand±held tester main switch ON.
(c) Select ACTIVE TEST mode on the hand±held tester.
CHECK:
Check that ºONº and ºOFFº of the VSC OFF (TRAC OFF) indicator light can be shown on the combination
meter with the hand±held tester.
ItemVehicle Condition / Test DetailsDiagnostic Note
VSC OFF (TRAC OFF)Turns VSC OFF (TRAC OFF) indicator ON / OFFObserve combination me-
ter
OK:
VSC OFF (TRAC OFF) indicator light comes on.
NG Go to step 4.
OK
2 Check center diff. lock (TRAC OFF) switch.
PREPARATION:
Remove center integration panel assembly (See page
BO±85).
CHECK:
Measure the resistance between terminals CSW and GND of
the center diff. lock
*1
(TRAC OFF *2) switch when the center diff.
lock
*1 (TRAC OFF *2) switch is ON and OFF.
*1
: Only for 4WD
*2 : Only for 2WD
OK:
Center diff. lock (TRAC OFF) switchResistance
Press continuouslyContinuity
Release1MW or higher
NG Replace center diff. lock (TRAC OFF) switch.
OK

F19788
6
IL2
7 CANL
S12
VSC+ 6
TC 28Translate ECU
CANH11
VSC±
TC
CG
J43
J/CIG 4A55
4BP±B W
L ABS & VSC Actuator
(Skid Control ECU)
7
S1T5
T5
T5 W
L
IL2
P±B D6
Data Link Connector 3
O 13
4Sub J/B No. 4
O
AA (*) CAN1 Circuit
(*)
(*)
(*) (*)
± DIAGNOSTICSABS WITH EBD & BA & TRAC & VSC SYSTEM
DI±1055
1249 Author: Date:
2005 SEQUOIA (RM1146U)
Tc Terminal Circuit
CIRCUIT DESCRIPTION
Connecting terminals Tc and CG of the DLC3 causes the skid control ECU to indicate the DTC by blinking
the ABS warning light, VSC TRAC warning light and BRAKE warning light.
WIRING DIAGRAM
DI94B±04