2001 TOYOTA SEQUOIA key

BE2ML±01
BE±82
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
3486 Author: Date:
2005 SEQUOIA (RM1146U)
THEFT DETERRENT SYSTEM
ON±VEHICLE INSPECTION
1. OUTLINE OF THEFT DETERRENT SYSTEM
When the theft deterrent system detects any theft, it informs
people around by flashing lights and sound.
All initial settings are performed in active mode. It can be
switched to passive mode by using the hand±held tester. (See
step 3. CHANGING METHOD OF PASSIVE MODE.)
HINT:
There are 4 conditions in this system: disarmed state, arming
preparation, armed state and alarm sounding.
(1) Disarmed state
Alarm function does not operate.
Theft deterrent function is not performed.
(2) Arming preparation
Time until transferring to armed state.
Theft deterrent function is not performed.
(3) Armed state
Theft deterrent function is ready.
(4) Alarm sounding:
When the system detects a theft, it informs people
around the vehicle using light and sound.
Refer to the table below for alarming method or
time.
Horn
Security horn
Alarm methodHeadlightAlarm method
Taillight
Interior light
Alarm time60 seconds
Alarm outputContinuous 0.4 secs. (ON)
0.4 secs. (OFF)
HINT:
Alarm output for the hazard is the same as the one for the haz-
ard on the vehicle.
If any of the doors is unlocked not by the key or wireless remote
control in the armed state, a force lock signal will be output.

Disarmed state
Perform any of the following and the system will go on to ºArming preparationº:

With all the doors, the engine hood and the back door closed, lock all doors with the key.

With all the doors, the engine hood and the back door closed, lock all doors by the
wireless remote control.

With all the doors, engine hood and back door locked, open and close any of the doors, the
engine hood or the back door, then close and lock all doors, the engine hood and the back door.
Arming preparation
Perform the following and the system will
go on to ºArmed stateº:

Let 30 seconds elapse with all the doors,
engine hood and the back door closed and
locked.
Perform any of the following and the system
will return to ºDisarmed stateº:

Open any of the doors, the engine hood or
the back door .

Unlock any of the doors or the back door.

Put the key in the key cylinder.

Reconnect the battery.
Armed state
Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors or the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
Perform any of the following and the system
will go on to ºAlarm soundingº:

Open any of the doors or the back door.

Unlock any of the doors or the back door in
any way other than with a key or by the wireless
remote control.

Open the engine hood.

Reconnect the battery.

When input from the optional glass break sensor
is detected (Dealer option).(Key not inserted in key cylinder.)
Alarm sounding
The vehicle's horn and security horn will sound,
and the hazard, interior, tail and head lights come
on for 60 seconds.
After the alarm has stopped, the system will
return to ºArmed stateº. Perform any of the following and the system
will return to ºDisarmed stateº:

Unlock any of the doors and the back door by
the wireless remote control.

Unlock any of the doors or the back door with
the key.

Put the key in the key cylinder and turn it ON.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±83
3487 Author: Date:
2005 SEQUOIA (RM1146U)
2. ACTIVE ARMING MODE

Perform any of the following and the system will go to disarmed state (B):

Turn the key from IG to OFF and remove the key from the ignition, open the driver's door.
Disarmed state (A)
Perform any of the following and the system
will return to disarmed state (A):

Push the unlock switch on the transmitter.

Put the key in the key cylinder.

Reconnect the battery.

Turn the ignition from OFF to ON.

Unlock any of the doors or back door with
the key.Disarmed state (B)Perform the following and the system will go
to arming preparation:

Close all the doors, hood and
back door.
Perform any of the following
and the system
will return to disarmed state
(B):

Open any of the doors, the
hood or the back door.
Arming preparation
Perform the following and the
system will go to armed state:

Allow 30 seconds to elapse
with all the doors, hood and
back door closed.
Perform any of the following and
the system
will return to disarmed state (A):

Push the unlock switch on the
transmitter.

Put the key in the ignition.

Reconnect the battery.

Turn the ignition from OFF to
ON.

Unlock any of the doors or back
door with the key.
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±85
3489 Author: Date:
2005 SEQUOIA (RM1146U)
3. PASSIVE ARMING MODE
This mode can be switched by the C±BEST customizing
function (See page DI±1684).
All modes are initially set to active when shipped from fac-
tory (no passive mode).

Perform the following and the system will return
to armed state:

Allow the alarm sounding period to pass.
Alarm sounding
Perform any of the following and the system will
return to disarmed state (A):

Push the unlock switch on the transmitter.

Put the key in the key cylinder and turn it ON.

Unlock any of the doors or the back door
with the key.
Perform any of the following and the system will
return to disarmed state (A): *

Push the unlock switch on the transmitter.

Put the key in the key cylinder and turn it ON.

Unlock any of the doors or the back door
with the key.
Armed state
Perform and/or detect any of the following
and the system will go on to alarm sounding:

Open any of the doors or the back door and
allow the entry delay time to pass.

Open the hood.

Reconnect the battery.

Ignition switch is connected directly.

Broken window glass.
BE±86
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
3490 Author: Date:
2005 SEQUOIA (RM1146U)

BE0CE±10
I28416
Theft Deterrent Horn
Engine Hood Courtesy Switch Engine Room J/B
Door Lock Assembly

Door Lock Motor

Door Unlock Detection Switch
Ignition Switch

Key Unlock Warning Switch
Instrument Panel J/B
Door Courtesy Light Switch
Horn
Back Door Lock Motor
Door Key Lock
and Unlock
Switch
Door Key Lock and
Unlock Switch Headlight
Doom Light
Taillight
Body ECU
(Located behind the Instrument Panel)
Engine Room R/B No. 2
Glass Breakage Sensor ECU
Glass Breakage
Sensor Microphone
± BODY ELECTRICALTHEFT DETERRENT SYSTEM
BE±91
3495 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

BE2MK±01
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±93
3497 Author: Date:
2005 SEQUOIA (RM1146U)
WIRELESS DOOR LOCK CONTROL SYSTEM
ON±VEHICLE INSPECTION
Make the vehicle in the initialized condition:
The initialized condition is the condition when the following conditions are satisfied.
(1) Key plate has not been inserted in the ignition key cylinder.
(2) All the doors are closed. (Door warning light is OFF.)
(3) All the doors are locked.
Under the standard operation, when repeating UNLOCK and LOCK switch 3 times or more alternately, check the
UNLOCK±LOCK operation from 3rd time onward.

Following procedures are standard operation.
(1) Keep about 1 M away to the right direction from the outside handle of a driver's seat.
(2) Face the transmitter toward the vehicle and press one of transmitter switches for about 1 sec.


As of the security function, even the wireless function is normal, there may be the case that only UNLOCK opera-
tion will not work.

As of the body customize function, if ºoperation twiceº has been set using hand±held tester, only driver's seat
is unlocked by unlock operation performed once.
Normal


Operative distance may differ according to
an operator, the way of holding the transmitter
or position.

Because weak electric wave is used, when
there is strong wave or noise in the used
frequency, operation distance might be
shortened.
No Yes
Only wireless function (Remote control) will not operate.
(If a new transmitter or a transmitter of the same type that works properly with the vehicle is not available.)
Basic function check:

BE±94
± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
3498 Author: Date:
2005 SEQUOIA (RM1146U)
Replace the transmitter battery with a new or normal
one and check UNLOCK±LOCK function works under
the standard operation.


The battery should be replaced by only the shops with
sufficient skill as new or normal battery is necessary.

Battery quality can be judged by checking the rem-
nant volume of the battery.
Ye s
Battery faulty.
No
Make the vehicle be in the initialized condition.
Enter into the self diagnostic mode.
If operating door control receiver in the order of 1 through 2, the mode turns to diagnostic mode.
(1) Insert the key plate in the ignition key cylinder and pull out, then insert it again and turn ignition switch
OFF " ON " OFF once within 5 seconds after pulling out.
(2) After completing the procedure within 30 seconds, turn the ignition switch OFF " ON " OFF 9 times.
HINT:
In the case that either (1) or (2) condition is not satisfied, transfer to normal mode.

When completing self±diagnostic mode, turn the ignition switch ON.
LOCK and UNLOCK operation and output of luggage door opener signal are not performed under the self
diagnostic mode.
1st time9th times ON
OFF
Transmitter battery check:
Inspection start by using self diagnostic mode:
within.
30 sec.within.
5 sec.
12 910
Key plate
not inserted
Key plate
inserted
Ignition
switch

± BODY ELECTRICALWIRELESS DOOR LOCK CONTROL SYSTEM
BE±95
3499 Author: Date:
2005 SEQUOIA (RM1146U)
No
No
(Not entered in self
diagnostic mode)Is the method to enter into the
diagnostic mode correct?
Self diagnostic mode operation check:
Ye s
(Entered in self diagnostic mode)
After the self±diagnostic mode input operation has
been performed, check that the buzzer chirps.
ON
OFF BuzzerIgnition switch OFF
0.13 sec. 0.5 sec.
Is the chirping function of operation
confirmation buzzer normal?
Check door control buzzer.
Check that continuity exists between
connector terminal A3 of MPX body ECU
on the vehicle side and ground by
inserting the key plate into the ignition
key cylinder. Key unlock warning switch inspection:
Ye s Ye s
No
Check key unlock warning switch.
Self diagnostic mode check:
Check that how the buzzer chirps when pressing
each transmitter switch.
ON
OFF Buzzer
0.13 sec.0.5 sec.
(1) Receiver normal wave of LOCK switch.
ON
OFF Buzzer
0.13 sec.
0.25 sec.
(2) Receiver normal wave of UNLOCK switch.
0.5 sec.
ON
OFF Buzzer
(3) Receiver normal wave of luggage door switch.
0.5 sec.0.5 sec.
ON
OFF (4) Incompatibility of the recognition code or out
from synchronization of rolling code.
While receiving
:
While turning the ignition switch ON in the self±
diagnostic mode, the mode returns to normal mode. Buzzer
(1), (2) or (3) are output.(4) is output.
(All buzzer's response
is same.)
Recognition code registration function check:
Check that it is possible to enter into
rewrite mode or add mode.
(Refer to ºWireless door lock receiver and
transmitterº ± ºRecognition code registrationº.)
Wireless door lock operates
normally when recognition code
is registered.
No response from buzzer