2001 TOYOTA SEQUOIA key

± DIAGNOSTICSAUDIO SYSTEM
DI±1989
2183 Author: Date:
2005 SEQUOIA (RM1146U)

*2: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.

*3: This code may be stored when the engine key is turned 1 min. again after engine start.

*4: This code may be stored when the engine key is turned again after engine start.

DIDB3±01
± DIAGNOSTICSREAR SEAT ENTERTAINMANT SYSTEM
DI±2103
2297 Author: Date:
2005 SEQUOIA (RM1146U)
DIAGNOSTIC TROUBLE CODE CHART
TermsMeaning
Physical addressThree±digit code (shown in hexadecimal) which is given to each component com-
prising the AVC±LAN.
Corresponding to the function, individual symbols are specified.
Logical addressTwo±digit code (shown in hexadecimal) which is given to each function comprising
the inner system of the AVC±LAN.
HINT:
DTC of the device which is directly connected via AVC±LAN, is displayed on the ºaudio system or navigation
systemº and the ºtelevision display assyº respectively.
Titles for each unit are stated in the following order: parts name (physical address) [Name indicated by DTC]
1. MULTI±DISPLAY CONTROLLER SUB±ASSY (Physical address: 16C, 16D) [RSE±ECU]
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

*2: This code is stored 180 seconds after the power supply connector is disconnected after engine
start.

*3: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position after engine start.

*4: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position in 1 minute after engine start.
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D8
*2No Response To Connection
CheckComponent shown by sub±code is or had been
disconnected from system after engine start.
1. Power source circuit (Television
display assy).
2. Power source circuit (Disc play-
er controller).
3. AVC±LAN circuit.
4. Replace television display assy.
5. Replace disc player controller.DI±2107
DI±2112
DI±2139
±
±
D9
*1Last Mode Error
Component operated (sound and/or image was
provided) before engine stop is or was discon-
nected with ignition switch in the ACC or ON posi-
tion.
1. Power source circuit (Television
display assy).
2. Power source circuit (Disc play-
er controller).
3. AVC±LAN circuit
4. Replace television display assy.
5. Replace disc player controller.DI±2107
DI±2112
DI±2139
±
±
DANo Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Detected when sound and picture do not change
by button operation.
1. Power source circuit (Television
display assy).
2. Power source circuit (Disc play-
er controller).
3. AVC±LAN circuit
4. Replace television display assy.
5. Replace disc player controller.DI±2107
DI±2112
DI±2139
±
±
DB
*1Mode Status ErrorDual alarm is detected.
1. Power source circuit (Television
display assy).
2. Power source circuit (Disc play-
er controller).
3. AVC±LAN circuit
4. Replace television display assy.
5. Replace disc player controller.DI±2107
DI±2112
DI±2139
±
±

DI±2104
± DIAGNOSTICSREAR SEAT ENTERTAINMANT SYSTEM
2298 Author: Date:
2005 SEQUOIA (RM1146U)DC
*4
Transmission Error
Transmission to component shown by sub±code
failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DE
*3Slave Reset (Momentary Inter-
ruption)After engine start, slave component has been dis-
connected.
1. Power source circuit (Television
display assy).
2. Power source circuit (Disc play-
er controller).
3. AVC±LAN circuit
4. Replace television display assy.
5. Replace disc player controller.DI±2107
DI±2112
DI±2139
±
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
2. Television display assy (Physical address: 1B0) [Rr±TV]
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

*2: This code may be stored when the engine key is turned again in 1 minute after the engine start.

*3: This code may be stored when the engine key is turned again after the engine start.

*4: The code is stored 210 seconds after the power supply connector of the master component is dis-
connected with the ignition switch in the ACC or ON position.
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
22RAM ErrorAbnormal condition of RAM is detected.Replace television display assy±
D6
*1Absence of Master
Component in which this code is recorded was
disconnected from system with the ignition switch
in the ACC or ON position. Or, when this code
was recorded, multi±display controller sub±assy
was disconnected.
1. Power source circuit (Television
display assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN circuit.
4. Replace television display assy.
5. Replace Multi±display controller
sub±assy.DI±2107
DI±2110
DI±2139
±
±
D7
*4Communication Check Error
Component in which this code is recorded is or
was disconnected from system after engine start.
Or, when recording this code, multi±display con-
troller sub±assy was disconnected.
1. Power source circuit (Television
display assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN circuit.
4. Replace television display assy.
5. Replace Multi±display controller
sub±assy.DI±2107
DI±2110
DI±2139
±
±
DC
*2Transmission Error
Transmission to component shown by sub±code
failed.
(Detecting this DTC does not necessarily mean
actual failure.)If the same sub±code is recorded in
other components, check harness
for power supply and communica-
tion system of all components
shown by code.
±

± DIAGNOSTICSREAR SEAT ENTERTAINMANT SYSTEM
DI±2105
2299 Author: Date:
2005 SEQUOIA (RM1146U)DD
*3
Master Reset (Momentary Inter-
ruption)After engine start, multi±display controller sub±
assy was disconnected from system.
1. Power source circuit (Television
display assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN circuit.
4. Replace television display assy.
5. Replace Multi±display controller
sub±assy.DI±2107
DI±2110
DI±2139
±
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (Television
display assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN circuit.
4. Replace television display assy.
5. Replace Multi±display controller
sub±assy.DI±2107
DI±2110
DI±2139
±
±
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E2ON/OFF Instruction Parameter
ErrorError occurs in ON/OFF controlling command
from multi±display controller sub±assy.Replace multi±display controller
sub±assy.±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Connection Check Instruction, Reg-
istration Request command is output from sub±
master component.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purposes, it may be de-
tected when no actual failure exists.
±
3. Disc player controller (Physical address: 1A0) [DVD±P]
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting an engine.

*2: This code may be stored when the engine key is turned again 1 min. after the engine starts.

*3: This code may be stored when the engine key is turned again after the engine starts.

*4: When 210 sec. have passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
22RAM ErrorAbnormal condition of RAM is detected.Replace disc player controller±
D6
*1Absence of Master
Component in which this code is recorded was
disconnected from system with the ignition switch
in the ACC or ON position. Or, when this code
was recorded, multi±display controller sub±assy
was disconnected.
1. Power source circuit (Disc play-
er controller).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN circuit.
4. Replace disc player controller.
5. Replace Multi±display controller
sub±assy.DI±2112
DI±2110
DI±2139
±
±

DI±2206
± DIAGNOSTICSNAVIGATION SYSTEM
2400 Author: Date:
2005 SEQUOIA (RM1146U) DC
*3
*5
Failure in transmission
This code indicates a transmission failure to the
device indicated by the sub code.
NOTE: This DTC may have no direct relationship
with the malfunction.
1. Power source circuit (Rear seat
audio controller). *6
2. Power source circuit (Multi±dis-
play controller sub±assy). *7
3. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
4. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
5. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
6. Replace stereo component am-
plifier assy.
7. Replace rear seat audio control-
ler. *6
8. Replace multi±display controller
sub±assy. *7DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±
DE
*4
*5
Slave resetThis code is stored when a slave device has been
disconnected after engine start.
1. Power source circuit (Stereo
component amplifier assy).
2. Power source circuit (Rear seat
audio controller). *6
3. Power source circuit (Multi±dis-
play controller sub±assy). *7
4. AVC±LAN circuit (Radio and
navigation assy ± Stereo compo-
nent amplifier assy).
5. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler). *6
6. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy). *7
7. Replace stereo component am-
plifier assy.
8. Replace rear seat audio control-
ler. *6
9. Replace multi±display controller
sub±assy. *7DI±2258
DI±2058
DI±2110
DI±2268
DI±2061
DI±2139
±
±
±
21ROM errorThis code is output when a malfunction exists in
ROM.Replace radio and navigation assy.±
22RAM errorThis code is output when a malfunction exists in
RAM.Replace radio and navigation assy.±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: If the power connector is disconnected after the engine starts, this code is recorded after 180 se-
conds.

*3: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*4: This code may be stored if the ignition key is held in the START position for 1 minute or more before
returning to the ON position.

*5: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*6: w/ Rear seat audio system only.

± DIAGNOSTICSNAVIGATION SYSTEM
DI±2209
2403 Author: Date:
2005 SEQUOIA (RM1146U)E2
ON/OFF indication parameter
errorWhen the command for ON/OFF control from the
master device has a problem.Replace radio and navigation assy.±
E3
*1Registration demand transmis-
sion
When the registration demand command from the
slave device is output, or when the registration
demand command is output by receiving connec-
tion confirmation command from the sub master
device.
NOTE: This DTC may not be directly related to
the problem.
±±
E4
*1Multiple frame incomplete
When the multiple frame transmission ends in-
complete.
NOTE: This DTC may not be directly related to
the problem.
±±
HINT:

*1: This code may be recorded depending on the battery condition or engine start voltage even if no
failure is detected.

*2: This code may be stored if the ignition key is turned to the START position again with the engine
running.

*3: This code may be stored if the ignition key is held in the START position for 1 minute or more before
returning to the ON position.

*4: If the device is reported as not existing during verification, check the power source circuit and AVC±
LAN circuit for the device.

*5: w/ Rear seat audio system only.

*6: w/ Rear seat entertainment system only.
3. Multi±display controller sub±assy (Physical address: 1F6) [RSE ECU, MAIN]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
21ROM ErrorAbnormal condition of ROM is detected.Replace multi±display controller
sub±assy.±
22ROM ErrorAbnormal condition of RAM is detected.Replace multi±display controller
sub±assy.±
D1
*1
*4Registered component discon-
nected
AVC±LAN transmitting abnor-
malitiesComponent shown by sub±code is or was discon-
nected from system with ignition switch in ACC or
ON.
Communication with component shown by sub±
code is not ensured when engine is started.
1. Power source circuit (Multi±dis-
play controller sub±assy).
2. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy).
3. Replace Multi±display controller
sub±assy.DI±2110
DI±2139
±
D7
*2AVC±LAN Communication
Check Error
Component in which this code is recorded is or
was disconnected from system after engine start.
Or, when recording this code, multi±display con-
troller was disconnected.
1. Power source circuit (radio and
navigation assy).
2. Power source circuit (Multi±dis-
play controller sub±assy).
3. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy).
4. Replace Multi±display controller
sub±assy.DI±2256
DI±2110
DI±2139
±
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
multi±display controller was disconnected.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy).
3. Replace Multi±display controller
sub±assy.DI±2256
DI±2139
±

DI±2210
± DIAGNOSTICSNAVIGATION SYSTEM
2404 Author: Date:
2005 SEQUOIA (RM1146U)DC
*1
*3
Transmission Error
Transmission to component shown by sub±code
has been failed.
(This code does not necessarily mean actual fail-
ure.)If same sub±code is recorded in
other component(s), check harness
for power supply and communica-
tion system of all components
shown by code.
±
DD
*4Master Reset (Momentary Inter-
ruption)Component that is to be master has been discon-
nected after engine start.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy).
3. Replace Multi±display controller
sub±assy.DI±2256
DI±2139
±
E0
*1Registration Completion
Instruction ErrorºRegistration Completion Instructionº command
from master cannot be received.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
E3
*1Registration Request Transmis-
sion

Registration Request command is output from
slave component.

Registration Request command is output from
sub±master component.Since this DTC is provided for engi-
neering, it may be detected when no
actual failure exists.
±
DF
*4Master Error
Due to defective condition of component with a
display, master function is switched to audio
equipment.
Error occurs in communication between sub±
master (audio) and master component.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Multi±display controller
sub±assy).
3. Replace Multi±display controller
sub±assy.DI±2256
DI±2139
±
E4
*1Multiple Frame AbortMultiple frame transmission is aborted.
Since this DTC is provided for engi-
neering purpose, it may be detected
when no actual failure exists.
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting an engine.

*2: This code is stored when 210 sec. has passed after the power supply connector is pulled out after
engine start.

*3: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position in 1 minute after engine start.

*4: This code may be stored when the engine key is turned back to the ON position and then turned
again to the START position after engine start.
4. Rear seat audio controller (Physical address: 1F4) [RSA]
(a) Logical address: 01 (Communication control)
DTCNameDiagnosisVerificationSee page
D6
*1Absence of Master
Component in which this code is recorded has
been disconnected from system with ignition in
ACC or ON. Or, when this code was recorded,
RSA panel was disconnected.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler).
3. Replace Rear seat audio control-
ler.DI±2256
DI±2061
±

DI±2212
± DIAGNOSTICSNAVIGATION SYSTEM
2406 Author: Date:
2005 SEQUOIA (RM1146U)DA
No Response to ON/OFF
Instruction
No response is identified when changing mode
(audio and visual mode change).
Detected when sound and picture does not
change by button operation
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler).
3. Replace Rear seat audio control-
ler.DI±2256
DI±2061
±
DB
*1Mode Status ErrorDual alarm is detected.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler).
3. Replace Rear seat audio control-
ler.DI±2256
DI±2061
±
DE
*4Slave Reset (Momentary Inter-
ruption)After engine start, slave component has been dis-
connected.
1. Power source circuit (radio and
navigation assy).
2. AVC±LAN (Radio and navigation
assy ± Rear seat audio control-
ler).
3. Replace Rear seat audio control-
ler.DI±2256
DI±2061
±
HINT:

*1: Even if no failure is detected, this code may be stored depending on the battery condition or voltage
for starting the engine.

*2: When 210 sec. has passed after pulling out the power supply connector of the master component
with the ignition switch in ACC or ON, this code is stored.

*3: This code may be stored when the engine key is turned 1 min. again after engine start.

*4: This code may be stored when the engine key is turned again after engine start.