2001 TOYOTA SEQUOIA key

Insert the master key in the key cylinder.
Driver's door: Open " Close 7 times Ignition switch: LOCK " ON 6 times
Remove the master key.START
END
*1
*2within
15 secs.
within
20 secs.
All doors closed. No key in the key cylinder.
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±141
3545 Author: Date:
2005 SEQUOIA (RM1146U)
3. ERASURE OF TRANSPONDER KEY CODE
Do this operation to erase transponder key registration from the transponder key computer.
HINT:
Delete all other master and sub±key codes leaving the master key code to use the operation. When using
the key which was used before deletion, it is necessary to register the code again.
*1: Insert the master cylinder into the key cylinder.
Turn the ignition switch to LOCK " ON 6 times within 15 seconds.
*2: Open and close driver's door 7 times and remove the master key within 20 seconds after completion of
the previous operation.
HINT:

When any operation time described above is over, registration mode completes.

When the next procedure is performed while the timer is working, the timer completes counting time,
then the next timer starts.
4. ECU COMMUNICATION ID REGISTRATION
NOTICE:

The ECU communication ID should be registered when the transponder key ECU and/or the
ECM is replaced, in order to match these ECM COMMUNICATION ID.

The engine cannot be started unless the ECM COMMUNICATION ID matches.
(a) Register the ECU communication ID.
(1) After the transponder key ECU and/or the ECM is replaced, turn the ignition switch ON (the en-
gine is not running).
(2) Short the Tc and CG terminals of the DLC3 and leave it as it is for 30 minutes.
(3) Check that the engine starts.

BE0D8±11
I28395
Transponder Key Coil
Transponder Key AmplifierECM
Instrument
Panel J/B

IGN 1 Fuse
Engine Room J/B

ECU±B Fuse

EFI No. 1 Fuse
Combination Meter

Security Indicator Light
DLC3
Transponder Key ECU
(Located behind the combination meter)
BE±142
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
3546 Author: Date:
2005 SEQUOIA (RM1146U)
LOCATION

BE2D6±02
I10154
I24870
12
6
± BODY ELECTRICALENGINE IMMOBILISER SYSTEM
BE±143
3547 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION
1. INSPECTION TRANSPONDER KEY COIL CONTINU-
ITY
Check that there is continuity between terminals 1 and 2.
If continuity is not as specified, replace the coil.
2. INSPECT TRANSPONDER KEY ECU CIRCUIT
Connect the wire harness side connector to the ECU and in-
spect the wire harness side connector from the back side, as
shown in the table below.
ConditionTester connectionSpecified condition
Always6 ± 12Battery positive voltage
If the circuit is as specified, replace the ECU with a new one.
If the circuit is not as specified, inspect the circuit connected to
other parts.

BO45T±01
H16689
Back Door Side Garnish
Back Door Center Garnishw/o Rear spoiler:
High Mount Stop Light
Outside MouldingBack Door Hingew/ Rear spoiler:
Rear Spoiler
Back Door Hinge
Rear Wiper Arm
Wiper
Motor
Grommet
Rear Wiper
Motor
Service Hole Plug
Outside MouldingStep Liner Back Door Glass Back Door Side
Garnish
Back Door Glass Run
Outer Weatherstrip
Back Door
Glass Guide Rail
Outer Cover
Power Window Regulator
Back Door
Glass Guide RailOutside Handle
Key Cylinder
Rear Light
Lower Stopper Rear Light Opening Hole Cover
Stopper Cushion
Back Door Lock ProtectorControl
Cable
Stopper Cushion
: Specified torque Strap Cover
Back Door Pull StrapBack Door Trim Board Inner WeatherstripNo. 1 Service
Hole Cover
Opening Hole Cover
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
5.5 (56, 49 in.´lbf)
5.5 (56, 49 in.´lbf)
8.0 (82, 71 in.´lbf)
N´m (kgf´cm, ft´lbf)No. 2 Service
Hole Cover
Back Door
Handle
Protector
Licence Plate
Light
Assembly
Outside
Garnish
Washer Nozzle
Lower Stopper
Power Window
Regulator Motor
Back Door Lock
19.5 (199, 14.4)
8.0 (82, 71 in.´lbf)
± BODYBACK DOOR
BO±25
3578 Author: Date:
2005 SEQUOIA (RM1146U)
BACK DOOR
COMPONENTS

H16683
H16684
5 Clips BO±30
± BODYBACK DOOR
3583 Author: Date:
2005 SEQUOIA (RM1146U)
(c) Using a screwdriver, remove the back door lock protector.
HINT:
Tape the screwdriver tip before use.
(d) Remove the 3 bolts and back door lock.
Torque: 8.0 N´m (82 kgf´cm, 71 in.´lbf)
19. REMOVE OUTSIDE GARNISH
(a) Remove the 2 service hole plugs.
(b) Remove the 2 nuts.
(c) Using a screwdriver, remove the outside garnish.
HINT:
Tape the screwdriver tip before use.
(d) Remove the 2 screws and outside handle from the out-
side garnish.
(e) Remove the nut and key cylinder from the outside gar-
nish.
(f) Remove the 4 screws and licence plate light assembly
from the outside garnish.
20. w/ Rear spoiler:
REMOVE REAR SPOILER (See page BO±174)
21. w/ o Rear spoiler:
REMOVE HIGH MOUNT STOP LIGHT

05_SEQUOIA_U (L/O 0408)
13
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
OPERATION OF INSTRUMENTS AND
CONTROLS
Keys and Doors
Keys14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobilizer system16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Side doors24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows28 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power back window31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent system36 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric moon roof40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1± 2

05_SEQUOIA_U (L/O 0408)
14
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)
Your vehicle is supplied with the two
kinds of keys.
1. Master keys (black)ÐThese keys work
in every lock. Your Toyota dealer will
need one of them to make a new key
with a built±in transponder chip.
2. Sub key (gray)ÐThis key will not work
in the glove box.
A transponder chip for engine immobilizer
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the side doors can be locked with-
out a key, you should always carry a
spare key in case you accidentally lock
your keys inside the vehicle.NOTICE
When using a key containing a trans-
ponder chip, observe the following
precautions:

When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
Keys

05_SEQUOIA_U (L/O 0408)
15
2005 SEQUOIA from Aug. '04 Prod. (OM34424U)

When starting the engine, do not
use the key with other transponder
keys around (including keys of oth-
er vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after remov-
ing other transporter keys (includ-
ing keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
Do not bend the key grip.

Do not cover the key grip with any
material that cuts off electromagnet-
ic waves.

Do not knock the key hard against
other objects.

Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under direct sunlight.

Do not put the key in water or
wash it in an ultrasonic washer.

Do not use the key with electromag-
netic materials.