2001 TOYOTA SEQUOIA O2 sensor harness

DI±1842
± DIAGNOSTICSPASSENGER DOOR CONTROL SYSTEM
2036 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check the jam protection pulse sensor circuit using DTC check (See page
DI±1904).
CHECK:
Check if DTC B1234 of the multiplex communication system is output.
OK:
DTC is not output.
OK Proceed to next circuit inspection shown in
problem symptoms table (See page DI±1818).
NG
2 Check jam protection pulse sensor (See page BE±69).
NG Replace the power window motor.
OK
3 Check wire harness and connector between jam protection pulse sensor and
passenger door ECU (See page IN±35).
NG Repair or replace wire harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1818).

DI±1848
± DIAGNOSTICSPASSENGER DOOR CONTROL SYSTEM
2042 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check remote control mirror position sensor (See page DI±1819).
NG Replace outer mirror.
OK
2 Check wire harness and connector between remote control mirror position sen-
sor and driver door ECU (See page IN±35).
NG Repair or replace harness or connector.
OK
Proceed to next circuit inspection shown in
problem symptoms table
(See page DI±1818).

DIDFA±01
I27698
B5
B6B7
DI±1894
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
2088 Author: Date:
2005 SEQUOIA (RM1146U)
TERMINALS OF ECU
1. CHECK BODY ECU
(a) Disconnect the B5, B6 and B7 ECU connectors.
(b) Measure the resistance or voltage of each terminal of the wire harness side connector.
Standard:
Symbols (Terminal No.)Wiring ColorTerminal DescriptionConditionSpecified Condition
BDR (B6±2) ±
Body groundL±W ± Body ground+B (BATT) power supplyAlways10 to 14 V
IG (B7±6) ± Body groundB±R ± Body groundIgnition power supplyIgnition switch ON10 to 14 V
ACC (B7±10) ±
Body groundGR ± Body groundACC power supplyIgnition switch ACC10 to 14 V
OBD2 (B5±2) ±
Body groundG±R ± Body groundBus º+º lineDuring transmissionPulse generation
S+B (B6±1) ± Body groundW±L ± Body ground+B (BATT) power supplyAlways10 to 14 V
BECU (B6±5) ±
Body groundW±R ± Body ground+B (BATT) power supplyAlways10 to 14 V
WIG (B7±5) ± Body groundL±Y ± Body groundIgnition power supplyIgnition switch ON10 to 14 V
MPX3 (B7±20) ±
Body groundG±O ± Body groundMPX lineAlways10 kW or higher
MPX2 (B5±24) ±
Body groundL±Y ± Body groundMPX lineAlways10 kW or higher
MPX1 (B7±22) ±
Body groundW±L ± Body groundMPX lineAlways10 kW or higher
GND1 (B6±6) ±
Body groundW±B ± Body groundGroundAlwaysBelow 1 W
PRG ± GND1
(B5±5 ± B6±6)V ± W±BWireless transmitter signal
groundWireless door look receiver
communication circuit±
RDA ± GND1
(B5±4 ± B6±6)R±G ± W±BWireless transmitter signal
inputWireless door lock control
system is operatedBelow 1 V
RDA ± GND1
(B5±4 ± B6±6)R±G ± W±BWireless transmitter signal
inputWireless door lock control
system is not operated10 to 14 V
GSW
(B6±16)GR±RAir bag sensor commu-
nication signalAir bag sensor commu-
nication circuit±
CLTS (*1) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control sen-
sor (Signal)Ignition switch OFFBelow 1 V
CLTS (*1) ± GND1
(B6±12 ± B6±6)Y ± W±BAutomatic light control sen-
sor (Signal)Ignition switch ONSignal waveform
CLTE (*1) ± GND1
(B6±3 ± B6±6)BR ± W±BAutomatic light control sen-
sor (Ground)AlwaysBelow 1 V

DI±1906
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
2100 Author: Date:
2005 SEQUOIA (RM1146U)B1242
(DI±1933)
Wireless door lock tuner circuit malfunction

Wireless door lock control receiver

Wire harness

Body ECU
B1243
(DI±1935)GSW terminal circuit malfunction

Airbag sensor assembly

Wire harness

Body ECU
B1244
(DI±1937)Light sensor circuit malfunction

Automatic light control sensor

Wire harness

Body ECU
B1262
(DI±1940)A/C ECU communication stop

A/C ECU (Integration control and panel)

Wire harness

Body ECU
B1271
(DI±1943)Combination meter ECU communication stop

Combination meter

Wire harness

Body ECU
B1272
(DI±1946)Memory seat ECU communication stop
(w/ Driving position memory)
Memory seat ECU & switch

Wire harness

Body ECU
B1273
(DI±1949)Sliding roof ECU communication stop
(w/ Sliding roof)
Sliding roof ECU

Wire harness

Body ECU
B1287
(DI±1952)Back door ECU communication stop

Back door ECU

Wire harness

Body ECU
HINT:

When either DTC B1214 or B1215 is output, a DTC for another ECU communication stop may also
be output. In this case, perform troubleshooting for DTC B1214 or B1215 first. DTC B1214 or B1215
is output when a short to +B or short to ground occurs on a communication bus.

DTCs from B1221 to B1241 do not indicate that the corresponding switch is abnormal. They notify how
the switch is operating.
If the corresponding DTC is not indicated when operating a switch, there is a problem with the switch
contact.
If a DTC is indicated when not operating switches, the corresponding switch is stuck.

I26946
Airbag Sensor Assembly Body ECU
A2018
GSW16
B6GSW Instrument Panel J/B
1A7
1B3
GR±R
B
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
DI±1935
2129 Author: Date:
2005 SEQUOIA (RM1146U)
DTC B1243 GSW terminal circuit malfunction
CIRCUIT DESCRIPTION
This DTC is indicated when open or ground short of the GSW terminal is detected.
DTC No.DTC Detection ConditionTrouble Area
B1243Open or ground short of GSW circuit

Airbag sensor assembly

Wire harness

Body ECU
WIRING DIAGRAM
DI1T3±09

DI±1936
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
2130 Author: Date:
2005 SEQUOIA (RM1146U)
INSPECTION PROCEDURE
1 Check for open and short in wire harness and connector between body ECU and
airbag sensor assembly.
PREPARATION:
Disconnect connector ºA20º of the airbag sensor assembly and connector ºB6º of the body ECU.
CHECK:
Check for an open or short circuit in the harness and connector between the airbag sensor assembly and
body ECU.
OK:
There is no open or short circuit in the wire harness.
NG Repair or replace wire harness or connector.
OK
2 Check the body ECU.
PREPARATION:
Check that DTC B1243 is indicated when another body ECU in good condition is installed.
CHECK:
Check if DTC B1243 is indicated after replacing the body ECU.
OK:
DTCs B1243 is not indicated.
NG Replace the airbag sensor assembly.
OK
Replace the body ECU (Original body ECU is
failure).

I24369
A27
Automatic Light Control
Sensor
B6 12
CLTB CLTS
CLTEBody ECU
R±GY
1 4
34
3
BRB6
B6 CLTB CLTS
CLTE
± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
DI±1937
2131 Author: Date:
2005 SEQUOIA (RM1146U)
DTC B1244 Light sensor circuit malfunction
CIRCUIT DESCRIPTION
This DTC is indicated when failure of the light sensor circuit is detected.
DTC No.DTC Detecting ConditionTrouble Area
B1244
Malfunction of automatic light control sensor

Open or short in automatic light control sensor circuit
Automatic light control sensor

Wire harness

Body ECU
WIRING DIAGRAM
DI639±08

± DIAGNOSTICSMULTIPLEX COMMUNICATION SYSTEM
DI±1939
2133 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check wire harness and connector between automatic light control sensor and
body ECU.
PREPARATION:
Disconnect connector ºA27º of the automatic light control sensor and connector ºB6º of the body ECU.
CHECK:
Measure the resistance according to the values in the table below.
OK:
Tester connection (Symbols)ConditionSpecified condition
A27±4 ± B6±12 (CLTS)AlwaysBelow 1 W
A27±1 ± B6±4 (CLTB)AlwaysBelow 1 W
A27±3 ± B6±3 (CLTE)AlwaysBelow 1 W
A27±4 ± Body groundAlways10 kW or higher
A27±1 ± Body groundAlways10 kW or higher
A27±3 ± Body groundAlways10 kW or higher
NG Repair or replace wire harness or connector.
OK
Replace the body ECU.