2001 TOYOTA SEQUOIA terminal TC

BO4S7±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±111
3664 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the body.

BO4S9±01
± BODYFRONT SEAT (Power Adjuster Type)
BO±123
3676 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO4SC±01
± BODYFRONT SEAT (Manual Adjuster Type)
BO±125
3678 Author: Date:
2005 SEQUOIA (RM1146U)
REMOVAL
CAUTION:
Work must not be started until at least 90 seconds after the ignition switch is turned to the LOCK posi-
tion and the negative (±) terminal cable is disconnected from the battery.
(The SRS is equipped with a back±up power source. If work is started within 90 seconds from discon-
necting the negative (±) terminal cable of the battery, the SRS may deploy.)
NOTICE:
When removing/installing and overhauling the passenger seat, check the passenger occupant clas-
sification system and perform the zero point calibration (see page DI±1128).
HINT:
The procedures listed below are for the LH side.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait for 90 seconds after disconnecting the cable to prevent the airbag working.
2. REMOVE SEAT TRACK COVERS
Using a screwdriver, remove the seat track covers.
HINT:
Tape the screwdriver tip before use.
3. REMOVE FRONT SEAT
(a) Remove the 4 bolts.
(b) Disconnect the connectors.
(c) w/ Side airbag:
Disconnect the airbag connector.
(d) Remove the front seat.
NOTICE:
Be careful not to damage the vehicle body.

BO4SF±01
BO±134
± BODYFRONT SEAT (Manual Adjuster Type)
3687 Author: Date:
2005 SEQUOIA (RM1146U)
INSTALLATION
HINT:
The procedures listed below are for the LH side.
1. INSTALL FRONT SEAT
(a) Mount the front seat to the vehicle.
NOTICE:
Be careful not to damage the vehicle body.
(b) w/ Side airbag:
Connect the airbag connector.
(c) Connect the connectors.
(d) Slide the front seat to the rearmost position.
(e) Tighten the bolts on the front side temporarily, starting from the bolt on the inner side.
(f) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
(g) Slide the front seat to the foremost position.
(h) Tighten the bolts on the rear side temporarily, starting from the bolt on the inner side.
(i) Tighten them completely.
Torque: 37 N´m (380 kgf´cm, 27 ft´lbf)
2. INSTALL SEAT TRACK COVERS
3. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
4. Passenger 's seat:
PERFORM PASSENGER OCCUPANT CLASSIFICATION SYSTEM ZERO POINT CALIBRATION
(See page DI±1128)
5. PERFORM INITIALIZATION (See page IN±20)
Some systems need initialization when disconnecting the cable from the negative battery terminal.

BO47Q±03
H24383Clip
H16718
Clip
H16719
4 Clips
± BODYSEAT BELT PRETENSIONER
BO±163
3716 Author: Date:
2005 SEQUOIA (RM1146U)
SEAT BELT PRETENSIONER
REMOVAL
NOTICE:

If the wiring connector of the supplemental restraint
system is disconnected with the ignition switch at ON
or ACC, diagnostic trouble codes will be recorded.

Never use SRS parts from another vehicle. When re-
placing parts, replace them with new parts.
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2. REMOVE FRONT DOOR SCUFF PLATE
Remove the 4 screws and front door scuff plate.
3. REMOVE FRONT DOOR OPENING TRIM WEATH-
ERSTRIP
4. REMOVE REAR DOOR SCUFF PLATE
(a) Remove the 3 screws.
(b) Using a screwdriver, remove the rear door scuff plate.
HINT:
Tape the screwdriver tip before use.
5. REMOVE REAR DOOR OPENING TRIM WEATH-
ERSTRIP
6. REMOVE LOWER CENTER PILLAR GARNISH
(a) Remove the front seat outer belt floor anchor.
(b) Using a screwdriver, remove the lower center pillar gar-
nish.
HINT:
Tape the screwdriver tip before use.

AB0158
SSTBattery
AB0152
SST
AB0158
SSTBattery
H01580
SST
± BODYSEAT BELT PRETENSIONER
BO±167
3720 Author: Date:
2005 SEQUOIA (RM1146U)
1. SEAT BELT PRETENSIONER ACTIVATION WHEN
SCRAPPING VEHICLE
HINT:
Have a battery ready as the power source to activate the seat
belt pretensioner.
(a) Check functioning of SST.
CAUTION:
When activating the seat belt pretensioner, always use the
specified SST: SRS Airbag Deployment Tool.
SST 09082±00700, 09082±00740
(1) Connect the SST to battery.
Connect the red clip of the SST to the battery posi-
tive (+) terminal and the black clip to the battery neg-
ative (±) terminal.
HINT:
Do not connect the yellow connector which will be connected
with the seat belt pretensioner.
(2) Check functioning of SST.
Press the SST activation switch, and check the LED
of the SST activation switch lights up.
CAUTION:
If the LED lights up when the activation switch is not being
pressed, SST malfunction is probable, so definitely do not
use the SST.
(b) Front seat outer belt on left side of 4±door vehicle:
Disconnect the pretensioner connector.
(1) Remove the front door scuff plate.
(2) Remove the back door scuff plate.
(3) Remove the rear quarter trim panel.
(4) Remove the quarter trim panel.

H18975
H18975
H02612
SST SST
R13455
10 m (33 ft) or more BO±168
± BODYSEAT BELT PRETENSIONER
3721 Author: Date:
2005 SEQUOIA (RM1146U)
(5) Disconnect the pretensioner connector as shown in
the illustration.
(6) Buckle the front seat belt and check that there is no
looseness and slack in the front seat inner belt and
front seat outer belt.
(c) Other front seat outer belts:
Disconnect the pretensioner connector.
(1) Remove the front door scuff plate.
(2) Remove the slide door scuff plate.
(3) Remove the center pillar lower garnish.
(4) Disconnect the pretensioner connector as shown in
the illustration.
(5) Buckle the front seat belt and check that there is no
looseness and slack in the front seat inner belt and
front seat outer belt.
(6) Connect the 2 SST each other, then connect them
to the seat belt pretensioner.
SST 09082±00700, 09082±00740
NOTICE:
To avoid damaging the SST connector and wire harness,
do not lock secondary lock of the twin lock.
(7) Move the SST to at least 10mm (33 ft) away from the
front of the vehicle.
(8) Close all the doors and windows of the vehicle.
NOTICE:
Take care not to damage the SST wire harness.
(9) Connect the SST red clip to the battery positive (+)
terminal and the black clip to the negative (±) termi-
nal.
(d) Activate seat belt pretensioner.
(1) Confirm that no one is inside the vehicle or within 10
m (33 ft) area around the vehicle.
(2) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).

H20776
SST SST
R05181
10 m (33 ft) or more
H20777
BO±170
± BODYSEAT BELT PRETENSIONER
3723 Author: Date:
2005 SEQUOIA (RM1146U)
(2) Place the front seat outer belt on the ground and
cover it with the disc wheel with tire.
NOTICE:
Place the front seat outer belt as shown in the illustration.
(3) Move the SST to at least 10 m (33 ft) away from the
disc wheel.
NOTICE:
Take care not to damage the SST wire harness.
(d) Activate the seat belt pretensioner.
(1) Connect the SST red clip to the battery positive (+)
terminal and black clip to the battery negative (±)
terminal.
(2) Check that no one is within 10 m (33 ft) area around
the disc wheel.
(3) Press the SST activation switch and activate the
seat belt pretensioner.
HINT:
The seat belt pretensioner operates simultaneously as the LED
of the SST activation switch lights up.
(e) Dispose of the front seat outer belt (with seat belt preten-
sioner).
CAUTION:

The front seat outer belt is very hot when the seat belt
pretensioner is activated, so leave it alone for at least
30 minutes after activation.

Use gloves and safety glasses when handling a front
seat outer belt with activated seat belt pretensioner.

Always wash your hands with water after completing
the operation.

Do not apply water, etc. to a front seat outer belt with
activated seat belt pretensioner.
(1) Remove the disc wheel and SST.
(2) Place the front seat outer belt in a vinyl bag, tie the
end tightly and dispose of it in the same way as oth-
er general parts.