2001 TOYOTA SEQUOIA terminal TC

B17438
Wire Harness Side:
Air Pump Connector
A43
DI±246
± DIAGNOSTICSENGINE
440 Author: Date:
2005 SEQUOIA (RM1146U)
HINT:

Using the AIR INJ CHECK operation of the SYSTEM CHECK provided in the hand±held tester func-
tion, conditions for air±fuel ratio and pressure in the secondary air injection system passage can be
checked while the secondary air injection system operating. It helps technicians to troubleshoot the
system when it malfunctioning.

Read freeze frame data using a hand±held tester. Freeze frame data record the engine condition when
malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle
was moving or stationary, if the engine was warmed up or not, if the air±fuel ratio was lean or rich, and
other data, from the time the malfunction occurred.
1 Check voltage between terminal 2 of air pump and body ground.
PREPARATION:
(a) Remove the intake manifold (see page EM±36).
(b) Disconnect the A43 air pump connector.
(c) Connect the hand±held tester to the DLC3.
(d) Turn the ignition switch ON and turn the tester ON.
CHECK:
(a) When the air pump is operated using the hand±held tes-
ter, measure the voltage between terminal A43±2 of the
air injection driver connector and body ground.
(b) Select the following menu items: DIAGNOSIS/EN-
HANCED OBD II/SYSTEM CHECK/ AIR INJ CHECK/
MANUAL OPERATION/OPERATION 1 and 3
HINT:
OPERATION 1: AP:OFF, EASV:CLOSE, ASV1:CLOSE,
ASV2:CLOSE
OPERATION 3: AP:ON, EASV:OPEN, ASV1:OPEN,
ASV2:OPEN
NOTICE:
This test only allows technicians to operate the AI system
for 5 seconds. Furthermore, the test can be performed 4
times a trip. If the test is repeated, intervals of at least 30
seconds are required between tests.
While the AI system operation using the hand±held tester
is prohibited, the tester displays the prohibition (WAIT or
ERROR). If the ERROR (AI STATUS NG) is displayed on the
tester, stop the engine for 10 minutes and then try again..
OK:
Standard:
Tester operationTester ConnectionSpecified Condition
Operation 3A43±2 ± Body ground10 V or more
Operation 1A43±2 ± Body groundBelow 1.0 V
NG Go to step 4.
OK

B17417
E4
PPMP
± DIAGNOSTICSENGINE
DI±269
463 Author: Date:
2005 SEQUOIA (RM1146U)
2 Measure resistance between terminal PPMP of ECM and body ground.
PREPARATION:
(a) Turn the ignition switch to OFF.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance between PPMP terminal of the ECM
connector and the body ground.
RESULT:
Test ResultsSuspected Trouble AreasProceed To
10 W or less
Wire harness/connector (ECM ± pressure sensor)

Short in pressure sensor circuitA
10 kW or more
Wire harness/connector (ECM ± pressure sensor)

Short in ECM circuitB
B Go to step 7.
A

B17417
E4
PPMP
A23446
L5
DI±270
± DIAGNOSTICSENGINE
464 Author: Date:
2005 SEQUOIA (RM1146U)
3 Measure resistance between terminal PPMP of ECM and body ground.
PREPARATION:
(a) Disconnect the L5 canister connector.
(b) Disconnect the E4 ECM connector.
CHECK:
Check the resistance between PPMP terminal of the ECM con-
nector and the body ground.
Result:
Test ResultsSuspected Trouble AreasProceed To
10 kW or more
Short in pressure sensor circuitA
10 W or less
Short in wire harness/connector (ECM ± pressure sensor)B
A Go to step 5.
B Go to step 6.

B17411
SPD(+) E6
E5
E1
AT7809
4 to 6 V
Turn the Wheel
3
2
1
I25536
Component Side Connector:
Vehicle Speed Sensor
± DIAGNOSTICSENGINE
DI±281
475 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check voltage between terminal SPD and E1 of ECM connector.
PREPARATION:
(a) Shift the shift lever to neutral.
(b) Jack up the rear wheel on one side.
(c) Turn the ignition switch ON.
CHECK:
Measure the voltage between the specified terminal of the E5
and E6 ECM connector when the wheel is turned slowly.
OK:
Standard:
Tester ConnectionSpecified Condition
SPD (E5±8) ± E1 (E6±1)Generated intermittently
HINT:
The output voltage should fluctuate up and down similarly to the
diagram on the left when the wheel is turned slowly.
OK Replace ECM (See page SF±80).
NG
3 Check vehicle speed sensor.
PREPARATION:
(a) Disconnect the vehicle speed sensor connector.
(b) Connect the battery positive (+) lead to terminal 1 and the
battery negative (±) lead to terminal 2.
(c) Connect the tester positive (+) lead to terminal 3 and the
tester negative (±) lead to terminal 2.
(d) Shift the shift lever to N position.
(e) Rotate the shaft.
CHECK:
Check that there is voltage change between terminals 2 and 3.
OK:
Standard: 0 V to 10 V or more
NG Replace vehicle speed sensor.
OK

BR3795OK NGClearance
B17411
SPD(+) E5
A23540
Wire Harness Side:
Front View
Combination Meter Connector C5
DI±282
± DIAGNOSTICSENGINE
476 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check sensor installation (Vehicle speed sensor).
CHECK:
Check the vehicle speed sensor installation.
OK:
The vehicle speed sensor is installed properly.
NG Tighten sensor installation bolt.
OK
5 Check for open and short in harness and connector between combination meter
and ECM.
PREPARATION:
(a) Disconnect the C5 combination meter connector.
(b) Disconnect the E5 ECM connector.
CHECK:
Check for resistance between the wire harness side connec-
tors.
OK:
Standard (Check for open):
Symbols (Terminal No.)Specified condition
SPD (E5±8) ± C5±25Below 1 W
Standard (Check for short):
Symbols (Terminal No.)Specified condition
SPD (E5±8) or C5±25 ± Body ground10 kW or higher
NG Repair or replace harness or connector.
OK
Check combination meter circuit (See page
DI±1632

B17446
Brake Pedal
DepressedBrake Pedal
Released ON
() ()
ST1±(+)E4
E6
E1(±)
DI±286
± DIAGNOSTICSENGINE
480 Author: Date:
2005 SEQUOIA (RM1146U)
3 Check STP signal and ST1± voltage.
PREPARATION:
(a) Connect the hand±held tester to the DLC3.
(b) Turn the ignition switch ON.
(c) Select the item ºDIAGNOSIS / ENHANCED OBD II /
DATA LIST / ALL / STOP LIGHT SWº.
CHECK:
Read the signal displayed on the hand±held tester.
OK:
Standard:
Brake PedalSpecified Condition
DepressedSTP Signal ON
ReleasedSTP Signal OFF
CHECK:
Measure the voltage between the specified terminals of the E4
and E6 ECM connectors.
OK:
Standard:
Tester ConnectionBrake PedalSpecified Condition
ST1± (E4±12) ±
E1 (E6±1)DepressedBelow 1.5 V
ST1± (E4±12) ±
E1 (E6±1)Released7.5 to 14 V
OK Check for intermittent problems (See page
DI±11).
NG

A21381
Engine Room J/B
EFI No. 1 Fuse
B17411
BATT (+) E6
E4
E1(±)
DI±294
± DIAGNOSTICSENGINE
488 Author: Date:
2005 SEQUOIA (RM1146U)
2 Check EFI No. 1 fuse of engine room J/B.
PREPARATION:
Remove the EFI No. 1 fuse from the engine room J/B.
CHECK:
Check the resistance of the EFI No. 1 fuse.
OK:
Standard: Below 1 W
NG Check for short in all harness and components
connected to EFI No. 1 fuse.
OK
3 Check voltage between terminal BATT and E1 of ECM connector.
CHECK:
Measure the voltage between terminals of the E6 and E4 ECM
connector.
OK:
Standard:
Tester ConnectionSpecified Condition
BATT (E4±3) ± E1 (E6±1)9 to 14 V
OK Check for intermittent problems
(See page DI±11).
NG

A21381
Engine Room J/B
EFI No. 1 Fuse
B17417
E4
BATT ECM Connector
± DIAGNOSTICSENGINE
DI±295
489 Author: Date:
2005 SEQUOIA (RM1146U)
4 Check for open and short in harness and connector between ECM and EFI No. 1
fuse, EFI No. 1 fuse and battery.
PREPARATION:
(a) Remove the EFI No. 1 fuse from the engine room J/B.
(b) Disconnect the E4 ECM connector.
CHECK:
Measure the resistance between the wire harness side connec-
tor.
OK:
Standard:
Tester ConnectionSpecified Condition
Engine Room J/B (EFI No. 1 fuse
terminal 2) ± BATT (E4±3)Below 1 W
Engine Room J/B (EFI No. 1 fuse
terminal 2) or BATT (E4±3) ±
Body ground
10 kW or higher
NG Repair or replace harness or connector.
OK
5 Check the battery (See page CH±1).
NG Replace battery.
OK
Check and replace engine room J/B.