2001 TOYOTA PRIUS air condition

PP3AD±01
± PREPARATIONAIR CONDITIONING
PP±57
11 8 Author: Date:
2001 PRIUS (RM778U)
AIR CONDITIONING
SST (Special Service Tools)
07110±58060Air Conditioner Service Tool Set
(07117±78050)Refrigerant Charging Gauge
(07117±88060)Refrigerant Charging HoseDischarge (Red)
(07117±88070)Refrigerant Charging HoseSuction (Blue)
(07117±88080)Refrigerant Charging HoseUtility (Green)
(07117±58060)Refrigerant Drain Service Valve
(07117±58080)Quick Disconnect AdapterDischarge (diam. 16 mm)
(07117±58090)Quick Disconnect AdapterSuction (diam. 13 mm)
(07117±58070)T±Joint
07116±38360Gas Leak Detector Assembly
07112±76050Magnetic Clutch Stopper
07112±66040Magnetic Clutch Remover

PP±58
± PREPARATIONAIR CONDITIONING
11 9 Author: Date:
2001 PRIUS (RM778U)
09870±00015A/C Quick Joint Puller No.1Suction tube
09870±00025A/C Quick Joint Puller No.2Liquid tube

PP3AE±01
± PREPARATIONAIR CONDITIONING
PP±59
2001 PRIUS (RM778U)
RECOMMENDED TOOLS
09040±00011Hexagon Wrench Set .
(09043±20050)Socket Hexagon Wrench 5.Expansion valve
5.0 mm (0.20 in.)
(09043±20100)Socket Hexagon Wrench 10.Radiator & condenser module
10 mm (0.39 in.)
09082±00040TOYOTA Electrical Tester.
09216±00021Belt Tension Gauge .
09905±00013Snap Ring Pliers .

PP3AF±02
PP±60
± PREPARATIONAIR CONDITIONING
2001 PRIUS (RM778U)
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
ThermometerSensor, ECT switch
Torque wrench
Dial indicatorMagnetic clutch
Plastic hammerMagnetic clutch

PP3AG±01
± PREPARATIONAIR CONDITIONING
PP±61
2001 PRIUS (RM778U)
LUBRICANT
ItemCapacityClassification
Compressor oil±ND±OIL 8 or equivalent
When replacing condenser40 cc (1.4 fl.oz.)
When replacing evaporator40 cc (1.4 fl.oz.)
When replacing compressor120 cc (4.1 fl.oz.)

DI±4
± DIAGNOSTICSENGINE
2001 PRIUS (RM778U)

The diagnosis system operates in normal mode
during normal vehicle use. It also has a check mode
for technicians to simulate malfunction symptoms
and troubleshoot. Most DTCs use 2 trip detection
logic* to prevent erroneous detection, and ensure
thorough malfunction detection. By switching the
ECM to check mode when troubleshooting, the
technician can cause the MIL to light up for a mal-
function that is only detected once or momentarily
(TOYOTA hand±held tester only). (See step 2)

*2 trip detection logic:
When a malfunction is first detected, the malfunc-
tion is temporarily stored in the ECM memory (1st
trip).
If the same malfunction is first detected again during the second
drive test, this second detection causes the MIL to light up (2nd
trip). (However, the IG switch must be turned OFF between the
1st trip and the 2nd trip.)

Freeze frame data:
Freeze frame data records the engine condition
when a misfire (DTC P0300 ± P0304) or fuel trim
malfunction (DTC P0171, P0172) or other malfunc-
tion (first malfunction only), is detected.

Because freeze frame data records the engine
conditions (fuel system, calculated load, engine
coolant temperature, fuel trim,engine speed, ve-
hicle speed, etc.) when the malfunction is detected,
when troubleshooting it is useful for determining
whether the vehicle was running or stopped, the en-
gine warmed up or not, the air±fuel ratio lean or rich,
etc. at the time of the malfunction.
Priorities for troubleshooting:
If troubleshooting priorities for multiple DTCs are given in the
applicable DTC chart, these should be followed.
If no instructions are given troubleshoot DTCs according to the
following priorities.
(1) DTCs other than fuel trim malfunction (DTC P0171,
P0172), and misfire (DTC P0300 ± P0304).
(2) Fuel trim malfunction (DTC P0171, P0172).
(3) Misfire (DTC P0300 ± P0304).

DI±8
± DIAGNOSTICSENGINE
2001 PRIUS (RM778U)
4. FAIL±SAFE CHART
If any of the following codes is recorded, the ECM enters fail±safe mode.
DTC No.Fail±Safe OperationFail±Safe Deactivation Conditions
P0100Ignition timing fixed at 5° BTDCReturned to normal condition
P0110Intake air temp. is fixed at 20°C (68°F)Returned to normal condition
P0115Engine coolant temp. is fixed at 80°C (176°F)Returned to normal condition
P0120VTA is fixed at 0°
The following condition must be repeated at least 2 times
consecutively
0.1 V
VTA
0.95 V
P0135
P0141The heater circuit in which an abnormality is detected is
turned offIgnition switch OFF
P0325Max. timing retardationIgnition switch OFF
P1300
P1305
P1310
P1315
Fuel cutIGF signal is detected for 2 consecutive ignitions
5. CHECK FOR INTERMITTENT PROBLEMS
TOYOTA hand±held tester only:
By putting the vehicle's ECM in check mode, 1 trip detection logic is possible instead of 2 trip detection logic
and sensitivity to detect open circuits is increased. This makes it easier to detect intermittent problems.
(1) Clear the DTC (See step 3).
(2) Set the check mode (See step 3).
(3) Perform a simulation test (See page IN±30).
(4) Check the connector and terminal (See page IN±41).
(5) Handle the connector (See page IN±41).
6. BASIC INSPECTION
When the malfunction code is not confirmed in the DTC check, troubleshooting should be performed in the
order for all possible circuits to be considered as the causes of the problems. In many cases, by carrying
out the basic engine check shown in the following flow chart, the location causing the problem can be found
quickly and efficiently. Therefore, use of this check is essential in engine troubleshooting.
1 Is battery positive voltage 11 V or more when engine is stopped?
NO Charge or replace battery.
YES
2 Does engine start?
NO Go to step 6.
YES

DI±12
± DIAGNOSTICSENGINE
2001 PRIUS (RM778U)
7. ENGINE OPERATING CONDITION
NOTICE:
The values given below for ºNormal Conditionº are representative values, so a vehicle may still be
normal even if its value varies from those listed here. So do not decide whether a part is faulty or
not solely according to the ºNormal Conditionº here.
(a) CARB mandated signals.
TOYOTA hand±held tester displayMeasurement ItemNormal Condition*
FUEL SYS #1
Fuel System Bank 1
OPEN: Air±fuel ratio feedback stopped
CLOSED: Air±fuel ratio feedback operating
Idling after warming up: CLOSED
CALC LOAD
Calculator Load:
Current intake air volume as a proportion of max.
intake air volumeIdling: 5.4 ± 19.2 %
Racing without load (2,250rpm): 6.9 ± 16.2 %
COOLANT TEMP.Engine Coolant Temp. Sensor ValueAfter warming up: 80 ± 95°C (176 ± 203°F)
SHORT FT #1Short±term Fuel Trim Bank 10 ± 20%
LONG FT #1Long±term Fuel Trim Bank 10 ± 20%
ENGINE SPDEngine SpeedIdling: 1,000 rpm
VEHICLE SPDVehicle SpeedVehicle Stopped: 0 km/h (0 mph)
IGN ADVANCEIgnition Advance:
Ignition Timing of Cylinder No. 1Idling: BTDC 7 ± 15°
INTAKE AIRIntake Air Temp. Sensor ValueEquivalent to Ambient Temp.
MAF/AFMAir Flow Rate Through Mass Flow Meter
Idling: 1.11 ± 4.38 gm/sec.
Racing without load (2,250 rpm):
3.38 ± 7.88 gm/sec.
THROTTLE POS
Voltage Output of Throttle Position Sensor
Calculated as a percentage:
0 V "0%, 5 V "100%Throttle Fully Closed: 0 ± 5 %
Throttle Fully Open: 90 ± 100 %
O2S B1, S1Voltage Output of Heated Oxygen Sensor Bank
1, Sensor 1Idling: 0.1 ± 0.9 V
O2FT B1, S1Heated Oxygen Sensor Fuel Trim Bank 1, Sen-
sor 1 (Same as SHORT FT #1)0 ± 20 %
O2S B1, S2Voltage Output of Heated Oxygen Sensor Bank
1, Sensor 2Driving at 50 km/h (31 mph): 0.1 ± 0.9 V
*: If no conditions are specifically stated for ºldlingº, it means the shift lever is at P position, the A/C switch
is OFF and all accessory switches are OFF.
(b) TOYOTA Enhanced Signals.
TOYOTA hand±held tester displayMeasurement ItemNormal Condition*
MISFIRE RPMEngine RPM for first misfire rangeMisfire 0: 0 rpm
MISFIRE LOADEngine load for first misfire rangeMisfire 0: 0 g/r
INJECTORFuel injection time for cylinder No.1Idling: 1.0 ± 3.0 ms
CYL#1, CYL#2, CYL#3, CYL#4Abnormal revolution variation for each cylinder0 %
IGNITIONTotal number of ignition for every 1,000 revolu-
tions0 ± 2,000
FUEL PUMPFuel Pump SignalIdling: ON
EVAP (PURGE) VSVEVAP VSV SignalVSV operating: ON
VAPOR PRESS VSVVapor Pressure VSV SignalVSV operating: ON
TOTAL FT B1Total Fuel Trim Bank 1: Average value for fuel
trim system of bank 1Idling: 0.8 ± 1.2 V