2001 NISSAN ALMERA transmission

SAT037DA
28. Remove brake band according to the following procedures.
a. Loosen lock nut, then back off anchor end pin.
+Do not reuse anchor end pin.
SAT038D
b. Remove brake band from transmission case.
SAT039D
+To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown in
the figure at left.
Leave the clip in position after removing the brake band.
SAT040D
c. Check brake band facing for damage, cracks, wear or burns.
SAT041D
29. Remove input shaft assembly (high clutch) and reverse clutch
according to the following procedures.
a. Remove input shaft assembly (high clutch) with reverse clutch.
DISASSEMBLY
AT-372

SAT042D
b. Remove input shaft assembly (high clutch) from reverse
clutch.
SAT043D
c. Remove needle bearing from high clutch drum.
d. Check input shaft assembly and needle bearing for damage or
wear.
SAT044D
30. Remove high clutch hub and needle bearing from transmission
case.
31. Check high clutch hub and needle bearing for damage or wear.
SAT579D
32. Remove front sun gear and needle bearings from transmission
case.
33. Check front sun gear and needle bearings for damage or wear.
SAT046D
34. Remove front planetary carrier assembly and low one-way
clutch according to the following procedures.
a. Remove snap ring using a screwdriver.
DISASSEMBLY
AT-373

SAT047D
b. Remove front planetary carrier with low one-way clutch.
SAT048D
c. Check that low one-way clutch rotates in the direction of the
arrow and locks in the opposite direction.
d. Remove low one-way clutch from front planetary carrier by
rotating it in the direction of unlock.
SAT049D
e. Remove needle bearing from front planetary carrier.
SAT050D
f. Check front planetary carrier, low one-way clutch and needle
bearing for damage or wear.
g. Check clearance between pinion washer and planetary carrier
using feeler gauge.
Standard clearance:
0.15 - 0.70 mm (0.0059 - 0.0276 in)
Allowable limit:
0.80 mm (0.0315 in)
Replace front planetary carrier if the clearance exceeds allow-
able limit.
SAT051D
35. Remove rear planetary carrier assembly and rear sun gear
according to the following procedures.
a. Remove rear planetary carrier assembly from transmission
case.
DISASSEMBLY
AT-374

SAT052D
b. Remove rear sun gear from rear planetary carrier.
SAT053D
c. Remove needle bearings from rear planetary carrier assembly.
SAT054D
d. Check rear planetary carrier, rear sun gear and needle bear-
ings for damage or wear.
e. Check clearance between pinion washer and rear planetary
carrier using feeler gauge.
Standard clearance:
0.15 - 0.70 mm (0.0059 - 0.0276 in)
Allowable limit:
0.80 mm (0.0315 in)
Replace rear planetary carrier if the clearance exceeds allow-
able limit.
SAT055D
36. Remove rear internal gear from transmission case.
SAT056D
37. Remove needle bearing from rear internal gear.
+Check needle bearing for damage or wear.
DISASSEMBLY
AT-375

SAT272E
38. Remove forward clutch assembly from transmission case.
AAT215A
39. Remove thrust washer from transmission case.
SAT702D
3AX00, 3AX01, 3AX19, 3AX63 and 3AX64 models
40. Remove side cover.
+Do not reuse side cover bolts.
SAT703D
41. Remove output shaft, output gear and reduction gear accord-
ing to the following procedures.
a. Set manual lever to ªPº position to fix idler gear and output
gear.
b. Unlock both idler gear and output gear lock nuts using a pin
punch.
SAT704D
c. Remove idler gear and output gear lock nuts.
+Do not reuse idler gear and output gear lock nuts.
DISASSEMBLY
AT-376

SAT841DA
d. Remove idler gear with puller.
SAT062K
e. Remove reduction pinion gear.
f. Remove reduction pinion gear bearing adjusting shim from
reduction pinion gear.
SAT064D
44. Remove return spring from parking shaft using a screwdriver.
SAT065D
45. Draw out parking shaft and remove parking pole from trans-
mission case.
46. Check parking pole and shaft for damage or wear.
SAT066D
47. Remove parking actuator support from transmission case.
+Check parking actuator support for damage or wear.
DISASSEMBLY
AT-379

SAT311G
48. Remove revolution sensor from transmission case.
DISASSEMBLY
AT-380

Manual Shaft
COMPONENTSNJAT0121
SAT481J
SAT313G
REMOVALNJAT01221. Remove detent spring from transmission case.
SAT076D
2. Drive out manual plate retaining pin.
SAT077D
3. Drive and pull out parking rod plate retaining pin.
4. Remove parking rod plate from manual shaft.
5. Draw out parking rod from transmission case.
REPAIR FOR COMPONENT PARTS
Manual Shaft
AT-381