2001 NISSAN ALMERA transmission

SAT049F
6. Pull out manual shaft retaining pin.
7. Remove manual shaft and manual plate from transmission
case.
SAT080D
8. Remove manual shaft oil seal.
INSPECTIONNJAT0123+Check component parts for wear or damage. Replace if nec-
essary.
SAT081D
INSTALLATIONNJAT01241. Install manual shaft oil seal.
+Apply ATF to outer surface of oil seal.
SAT610H
2. Install manual shaft and manual plate.
REPAIR FOR COMPONENT PARTS
Manual Shaft (Cont'd)
AT-382

SAT074E
3. Align groove of manual shaft and hole of transmission case.
4. Install manual shaft retaining pin.
SAT078D
5. Install parking rod to parking rod plate.
6. Set parking rod assembly onto manual shaft.
SAT087D
7. Drive in manual plate retaining pin and parking rod plate retain-
ing pin.
SAT313G
8. Install detent spring.
REPAIR FOR COMPONENT PARTS
Manual Shaft (Cont'd)
AT-383

Low & Reverse Brake
COMPONENTS=NJAT0153
SAT039K
SAT230D
DISASSEMBLYNJAT01541. Check operation of low & reverse brake.
a. Apply compressed air to oil hole of transmission case.
b. Check to see that retaining plate moves to snap ring.
c. If retaining plate does not contact snap ring:
+D-ring might be damaged.
+Oil seal might be damaged.
+Fluid might be leaking past piston check ball.
SAT231D
2. Stand transmission case.
3. Remove snap ring.
4. Remove drive plates, driven plates, retaining plate from trans-
mission case.
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake
AT-419

SAT242D
5. Set Tool on spring retainer and remove snap ring while com-
pressing return springs.
+Set Tool directly above return springs.
+Do not expand snap ring excessively.
6. Remove spring retainer and return springs.
SAT303E
+Do not remove return springs from spring retainer.
SAT234D
7. Apply compressed air to oil hole of transmission case while
holding piston.
8. Remove piston from transmission case by turning it.
SAT767G
9. Remove D-ring and oil seal from piston.
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake (Cont'd)
AT-420

INSPECTIONNJAT0155Low & Reverse Clutch Snap Ring, Spring Retainer and
Return Springs
NJAT0155S01+Check for deformation, fatigue or damage.
+Replace if necessary.
+When replacing spring retainer and return springs,
replace them as a set.
SAT162D
Low & Reverse Brake Drive PlatesNJAT0155S02+Check facing for burns, cracks or damage.
+Measure thickness of facing.
Thickness of drive plate:
Standard value: 2.0 mm (0.079 in)
Wear limit: 1.8 mm (0.071 in)
+If not within wear limit, replace.
SAT235DA
ASSEMBLYNJAT01561. Install D-ring and oil seal on piston.
+Take care with the direction of the oil seal.
+Apply ATF to both parts.
SAT239D
2. Stand transmission case.
3. Install piston assembly on transmission case while turning it
slowly.
+Apply ATF to inner surface of transmission case.
SAT241D
4. Install return springs and spring retainer on piston.
For return spring, refer to AT-477.
REPAIR FOR COMPONENT PARTS
Low & Reverse Brake (Cont'd)
AT-421

NAT047
7. Remove idler gear bearing outer race from transmission case.
NAT048
8. Press out reduction pinion gear bearing from reduction pinion
gear.
SAT651D
9. Remove reduction pinion gear bearing outer race from trans-
mission case.
SPD715
INSPECTIONNJAT0241Output Shaft, Output Gear, Idler Gear and Reduction
Pinion Gear
NJAT0241S01+Check shafts for cracks, wear or bending.
+Check gears for wear, chips and cracks.
BearingsNJAT0241S02+Make sure bearings roll freely and are free from noise, cracks,
pitting or wear.
+When replacing taper roller bearing, replace inner and
outer race as a set.
SAT671D
Seal Ring ClearanceNJAT0241S03+Install new seal rings to output shaft.
+Measure clearance between seal ring and ring groove of out-
put shaft.
Standard clearance:
0.10 - 0.25 mm (0.0039 - 0.0098 in)
Wear limit:
0.25 mm (0.0098 in)
+If not within wear limit, replace output shaft.
+Install new seal rings to bearing retainer.
REPAIR FOR COMPONENT PARTS
O/Shaft, O/Gear, I/Gear, R/Pinion Gear and B/Retainer Ð 3AX00, 01, 19, 63 and 64 models (Cont'd)
AT-429

+Measure clearance between seal ring and ring groove of bear-
ing retainer.
Standard clearance:
0.10 - 0.25 mm (0.0039 - 0.0098 in)
Wear limit:
0.25 mm (0.0098 in)
+If not within wear limit, replace bearing retainer.
NAT049
ASSEMBLYNJAT02421. Press reduction pinion gear bearing on reduction pinion gear.
SAT654D
2. Install reduction pinion gear bearing outer race on transmis-
sion case.
SAT655D
3. Press idler gear bearing inner race on idler gear.
NAT051
4. Install idler gear bearing outer race on transmission case.
REPAIR FOR COMPONENT PARTS
O/Shaft, O/Gear, I/Gear, R/Pinion Gear and B/Retainer Ð 3AX00, 01, 19, 63 and 64 models (Cont'd)
AT-430

NAT047
6. Remove idler gear bearing outer race from transmission case.
NAT048
7. Press out reduction pinion gear bearing from reduction pinion
gear.
SAT651D
8. Remove reduction pinion gear bearing outer race from trans-
mission case.
INSPECTIONNJAT0163Output Shaft, Idler Gear and Reduction Pinion GearNJAT0163S01+Check shafts for cracks, wear or bending.
+Check gears for wear, chips and cracks.
SPD715
BearingNJAT0163S02+Make sure bearings roll freely and are free from noise, cracks,
pitting or wear.
+When replacing taper roller bearing, replace outer and
inner race as a set.
REPAIR FOR COMPONENT PARTS
Output Shaft, Idler Gear, Reduction Pinion Gear and Bearing Retainer Ð 3AX10 and 3AX18 models (Cont'd)
AT-434