2000 TOYOTA CAMRY oil

AUTOMATIC TRANSAXLEVALVE BODY ±
AX±83
(b) Position a new gasket and plate and then another new
gasket.
HINT: Both gaskets are identical.
(c) Install the 2 screws.
8. INSTALL NO.2 LOWER VALVE BODY COVER
(a) Position the No.2 lower valve body cover.
(b) Install and finger tighten the 11 bolts.
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 40 mm (1.575 in.)
Bolt B: 44 mm (1.732 in.)
Bolt C: 14 mm (0.551in.)
9. INSTALL OIL STRAINER AND CHECK VALVE
Install the oil strainer and check valve into the lower valve
body.

AUTOMATIC TRANSAXLEVALVE BODY ±
AX±84
10. INSTALL LOWER VALVE BODY COVER GASKETS
AND NO.2 PLATE
Position a new gasket and plate and then another new
gasket.
HINT: Both gaskets are identical.
11. INSTALL LOWER VALVE BODY COVER
(a) Position the lower valve body cover.
(b) Install and finger tighten the 5 bolts.
HINT: Each bolt length is indicated below.
Bolt length
Bolt A: 47 mm (1.850 in.)
Bolt B: 14 mm (0.551 in.)
12. INSTALL PRESSURE RELIEF VALVE
13. TIGHTEN BOLTS OF UPPER AND LOWER VALVE BO-
DIES
(a) Tighten the 16 bolts in the lower valve body.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
(b) Tighten the 3 bolts in the upper valve body.
Torque: 6.6 N´m (67 kgf´cm, 58 in.´lbf)
14. INSTALL B0 ACCUMULATOR ASSEMBLY
(a) Coat new O±rings with ATF and install them to the piston.
(b) Install the spring and piston into the cylinder.
Spring dimensions
mm (in.)
ColorFree lengthCoil outer diameter
Inner White47.5 (1.870)18.9 (0.744)
Outer None16.3 (0.642)20.7 (0.815)

AUTOMATIC TRANSAXLEUPPER VALVE BODY ±
AX±87
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During reassembly please refer to the spring specifications above to help discriminate between
the different springs.
Mar
kName (Color)Free Length / Outer Diameter
mm (in.)Total No. of Coils
@@
@@
@:
[c A]
Lock±Up Relay Valve (Yellow)26.8 (1.055) / 10.2 (0.402)10.8
@@
@@
@:
[c B]
B1 Orifice Control Valve (White)24.8 (0.976) / 6.4 (0.252)12.0
@@
@@
@:
[c C]
Throttle Valve (Green)31.5 (1.240) / 7.0 (0.276)11.4
@@
@@
@:
[c D]
Down±Shift Plug (None)15.0 (0.591) / 11.0 (0.433)7.0
AX048±03

AUTOMATIC TRANSAXLELOWER VALVE BODY ±
AX±91
VALVE BODY SPRINGS SPECIFICATIONS
HINT: During reassembly please refer to the spring specifications above to help discriminate between
the different springs.
Mar
kName (Color)Free Length / Outer Diameter
mm (in.)Total No. of Coils
@@
@@
@:
[c A]
Accumulator Control Valve (Red)25.1 (0.988) / 8.6 (0.339)8.0
@@
@@
@:
[c B]
2±3 Shift Valve (None)28.0 (1.102) / 7.6 (0.299)10.3
@@
@@
@:
[c C]
1±2 Shift Valve (Light Green)29.2 (1.150) / 8.9 (0.350)12.0
@@
@@
@:
[c D]
Reverse Control Valve (White/Purple)38.1 (1.500) / 6.5 (0.256)19.0
AX04B±03

AUTOMATIC TRANSAXLEDIFFERENTIAL ASSEMBLY ±
AX±98
(d) Check the side gear backlash.
Measure the side gear backlash while holding one pinion
gear toward the case.
Standard backlash:
0.05±0.20 mm (0.0020±0.0079 in.)
Refering to the table below, select thrust washers which
will ensure that the backlash is within specification. Try to
select washers of the same size for both sides.
Thrust washer thickness
mm (in.)
Thickness mm (in.)Thickness mm (in.)
1.60 (0.0630)1.70 (0.0670)
1.80 (0.0709)
If the backlash is not within specification, install a thrust
washer of a different thickness.
(e) Using a pin punch and hammer, drive the lock pin through
the case and hole in the pinion shaft.
(f) Stake the differential case.
2. INSTALL RING GEAR
(a) Clean the contact surface of the differential case.
(b) Heat the ring gear to about 100°C (212°F) in an oil bath.
NOTICE: Do not heat the ring gear above 110°C (230°F).
(c) Carefully remove the ring gear from the oil bath.
(d) Clean the contact surface of the ring gear with cleaning
solvent.
(e) Quickly install the ring gear on the differential case.
Install the 12 bolts.
HINT: Align the matchmarks on the differential left case
and contact the ring gear.
(f) Tighten the set bolts uniformly a little at a time.
Torque the bolts.
Torque: 124 N´m (1,260 kgf´cm, 91 ft´lbf)

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±102
DIFFERENTIAL AND DRIVE PINION
INSTALLATION
1. INSTALL DRIVE PINION INTO TRANSAXLE CASE
(a) Using SST, install the bearing to the drive pinion shaft.
SST 09350±32014 (09351±32120)
(b) Place the bearing cage onto the drive pinion shaft.
NOTICE: Be careful not to damage the oil seals with the
pinion shaft.
(c) Using a brass bar and hammer, slightly tap the bearing
cage into the transaxle case until the snap ring groove in
the bore can be seen.
(d) Using SST, install snap ring into the bore.
SST 09350±32014 (09351±32050)
(e) Using SST, install the snap ring.
SST 09350±32014 (09351±32050)
AX0U1±02

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±103
2. PLACE OIL SLINGER AND NEW SPACER
HINT: Install the spacer with the small end downward.
3. INSTALL OUTER RACE TO TRANSAXLE CASE
Using SST, press in the outer race.
SST 09350±32014 (09351±32100, 09351±32140)
4. INSTALL COUNTER DRIVE GEAR
(a) Place a brass bar into the transaxle hole to hold the drive
pinion shaft.
(b) Using SST, press in the counter driven gear until the
counter driven gaer bearing almost touches the counter
gear.
SST 09350±32014 (09351±32140)
5. INSTALL NEW LOCK NUT AND ADJUST DRIVE PIN-
ION PRELOAD
(a) Install the new lock nut.
(b) Using SST to hold the gear, tighten the nut.
Torque: 280 N´m (2,855 kgf´cm, 206 ft´lbf)
SST 09330±00021, 09350±32014 (09351±32032)
(c) Turn the gear counterclockwise and clockwise several
times.
(d) Using a small torque wrench, measure the preload of the
drive pinion.
Drive pinion preload (at starting):
New bearing
1.0±1.6 N´m (10±16 kgf´cm, 8.7±13.9 in.´lbf)
Reused bearing
0.5±0.8 N´m (5±8 kgf´cm, 4.3±6.9 in.´lbf)

If the preload is greater than specified, replace the
bearing spacer.

AUTOMATIC TRANSAXLECOMPONENT PARTS INSTALLATION ±
AX±105
9. INSTALL CARRIER COVER
(a) Remove any packing material and be careful not to drop
oil on the contacting surfaces of the carrier cover and
transaxle case.
(b) Apply seal packing to the carrier cover.
Seal packing:
Part No.08826±00090, THREE BOND 1281 or equiva-
lent
HINT: Install the carrier cover within 10 minutes after ap-
plying seal packing.
(c) Install and torque the 11 bolts.
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
HINT: Each bolt length is indicated below.
Bolt length:
Bolt A: 100 mm (3.937 in.)
Bolt B: 65 mm (2.559 in.)
Bolt C: 75 mm (2.953 in.)
10. ADJUST SIDE BEARING PRELOAD
(a) Remove any packing material on the contacting surfaces
of the LH bearing retainer and transaxle case.
HINT: Do not apply seal packing yet.
(b) Install the LH bearing retainer and torque the 6 bolts.
Torque: 19 N´m (195 kgf´cm, 14 ft´lbf)
(c) Snap down the bearings by turning the differential case
several times.
(d) Using a small torque wrench, measure the differential to-
tal preload.
Total preload (at starting):
New bearing
Drive pinion preload plus 0.2±0.4 N´m
(2.5±5.1 kgf´cm, 2.2±3.6 in.´lbf)
Reused bearing
Drive pinion preload plus 0.1±0.2 N´m
(1.3±2.0 kgf´cm, 1.1±1.7 in.´lbf)
If the preload is not within specification, replace the ad-
justing shim in the LH bearing retainer with one of a differ-
ent thickness.