2000 TOYOTA CAMRY engine mount

A06646
RH Drive Shaft
LH Drive Shaft
Tie Rod End
49 (500, 36)
294 (3,000, 217)64 (650, 47)32 (320, 23)
RH Engine
Mounting Stay
Lower Suspension Arm Engine Moving
Control Rod
64 (650, 47)
127 (1,300, 94)
No.2 RH Engine
Mounting Stay (M/T)
No.2 RH Engine
Mounting Bracket
Engine and Transaxle
Assembly
64 (650, 47)
66 (670, 48)
64 (650, 47)
Front Engine
Mounting Insulator
48 (490, 35)
64 (650, 47)
Transaxle
Control Cable
Engine Mounting Absorber
TMC Made 80 (820,59)
TMMK Made
Green Clolr Bolt 66 (670, 48)
Silver Clolr Bolt 44 (450,32)
N´m (kgf´cm, ft´lbf) : Specified torque

Non±reusable part

Rear Engine
Mounting
Insulator
EM±70
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
1356 Author: Date:

P18775
S05393
M/T
Z18907
A/T
P18752
A05426
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
EM±73
1359 Author: Date:
18. DISCONNECT PS PUMP FROM ENGINE
(a) Remove the 2 nuts, and disconnect the PS pressure tube
from the No.1 engine hanger.
(b) Loosen the 2 bolts, and remove the drive belt.
(c) Remove the 2 bolts, and disconnect the PS pump from
the engine.
19. DISCONNECT TRANSAXLE FROM LH ENGINE
MOUNTING INSULATOR
(a) M/T:
Remove the 3 bolts holding the transaxle to the mounting
insulator.
(b) A/T:
Remove the 4 bolts holding the transaxle to the mounting
insulator.
20. DISCONNECT REAR ENGINE MOUNTING BRACKET
FROM FRONT FRAME
(a) Remove the 2 hole plugs.
(b) Remove the 4 nuts holding the front frame to the mount-
ing bracket.
21. REMOVE ENGINE MOUNTING ABSORBER
Remove the 4 bolts and mounting absorber.

P18755
P19478
Engine
Hanger
S04501
S05451
EM±74
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
1360 Author: Date:
22. DISCONNECT FRONT ENGINE MOUNTING
INSULATOR FROM FRONT FRAME
Remove the 3 bolts holding the mounting insulator to the front
frame.
23. ATTACH ENGINE SLING DEVICE TO ENGINE
HANGERS
(a) Install the No.2 engine hanger in the correct direction.
Part No.:
No.2 engine hanger12282±20020
Bolt91621±60822
Torque: 19.5 N´m (200 kgf´cm, 14 ft´lbf)
(b) Attach the sling device to the engine hangers.
CAUTION:
Do not attempt to hang the engine by hooking the chain to
any other part.
24. REMOVE RH ENGINE MOUNTING STAY
Remove the 3 bolts and RH engine mounting stay.
25. M/T only:
REMOVE NO.2 RH ENGINE MOUNTING STAY
Remove the 2 bolts and No.2 RH engine mounting stay.

S04754
S04993
Lift
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
EM±75
1361 Author: Date:
26. REMOVE ENGINE MOVING CONTROL ROD AND
NO.2 RH ENGINE MOUNTING BRACKET
Remove the 3 bolts, control rod and mounting bracket.
27. REMOVE ENGINE AND TRANSAXLE ASSEMBLY
FROM VEHICLE
(a) Lift the engine out of the vehicle slowly and carefully.
NOTICE:

Be careful not to hit the PNP switch.

Make sure the engine is clear of all wiring, hoses and
cables.
(b) Place the engine and transaxle assembly onto the stand.
28. REMOVE FRONT ENGINE MOUNTING INSULATOR
FROM ENGINE
Remove the 4 bolts and mounting insulator.
29. REMOVE REAR ENGINE MOUNTING INSULATOR
AND BRACKET ASSEMBLY FROM ENGINE
Remove the 4 bolts, the mounting insulator and bracket assem-
bly.
30. SEPARATE ENGINE AND TRANSAXLE
E153 M/T (See page MX±4)
A541E A/T (See page AX±23)

EM04Z±04
S04992
Lower
S04754
S05451
S04501
EM±76
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
1362 Author: Date:
INSTALLATION
1. ASSEMBLE ENGINE AND TRANSAXLE
E153 M/T (See page MX±4)
A541E A/T (See page AX±23)
2. INSTALL REAR ENGINE MOUNTING INSULATOR
Install the mounting insulator with the 4 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
3. INSTALL FRONT ENGINE MOUNTING INSULATOR
Install the mounting insulator with the 4 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
4. INSTALL ENGINE AND TRANSAXLE ASSEMBLY IN
VEHICLE
(a) Attach the engine sling device to the engine hangers.
(b) Lower the engine into the engine compartment.
Tilt the transaxle downward, lower the engine and clear
the LH mounting.
NOTICE:
Be careful not to hit the park/neutral position switch.
(c) Keep the engine level, and align RH and LH mountings
with the body bracket.
5. INSTALL NO.2 RH ENGINE MOUNTING BRACKET
AND ENGINE MOVING CONTROL ROD
Install the mounting moving control rod and No.2 RH engine
mounting bracket with the 3 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
6. M/T only:
INSTALL NO.2 RH ENGINE MOUNTING STAY
Install the No.2 RH engine mounting stay with the 2 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
7. INSTALL RH ENGINE MOUNTING STAY
Install the RH mounting stay with the 3 bolts.
Torque: 32 N´m (320 kgf´cm, 23 ft´lbf)

P18755
A05426
P18752
S05393
M/T
Z18907
A/T
± ENGINE MECHANICAL (1MZ±FE)ENGINE UNIT
EM±77
1363 Author: Date:
8. CONNECT FRONT ENGINE MOUNTING
INSULATOR
Connect the mounting insulator with the 3 bolts.
Torque:
TMC made: 80 N´m (820 kgf´cm, 59 ft´lbf)
TMMK made:
44 N´m (450 kgf´cm, 32 ft´lbf) for silver color bolt
66 N´m (670 kgf´cm, 48 ft´lbf) for green color bolt
9. INSTALL ENGINE MOUNTING ABSORBER
Install the engine mounting absorber with the 4 bolts.
Torque: 48 N´m (490 kgf´cm, 35 ft´lbf)
10. CONNECT REAR ENGINE MOUNTING INSULATOR
(a) Connect the mounting insulator with the 4 nuts.
Torque: 66 N´m (670 kgf´cm, 48 ft´lbf)
(b) Install the 2 hole plugs.
11. CONNECT LH ENGINE MOUNTING INSULATOR
(a) M/T:
Connect the mounting insulator with the 3 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
(b) A/T:
Connect the mounting insulator with the 4 bolts.
Torque: 64 N´m (650 kgf´cm, 47 ft´lbf)
12. REMOVE ENGINE SLING DEVICE
13. CONNECT TRANSAXLE CONTROL CABLE(S) TO
TRANSAXLE

P12909
Seal Width 3 ± 5 mm
Z14261
1
23
45 6
7
89
10
P12389
SST
± ENGINE MECHANICAL (1MZ±FE)CYLINDER BLOCK
EM±109
1395 Author: Date:

Using a non±residue solvent, clean both sealing
surfaces.
(b) Apply seal packing to the water inlet housing as shown in
the illustration.
Seal packing: Part No. 08826±00100 or equivalent

Install a nozzle that has been cut to a 3 ± 5 mm (0.12
± 0.20 in.) opening.
HINT:
Avoid applying an excessive amount to the surface.

Parts must be assembled within 3 minutes of ap-
plication. Otherwise the material must be removed
and reapplied.

Immediately remove nozzle from the tube and rein-
stall cap.
(c) Install the water inlet housing with the 8 bolts and 2 nuts.
Uniformly tighten the bolts and nuts, in several passes, in
the sequence shown.
Torque: 8 N´m (80 kgf´cm, 69 in.´lbf)
(d) Install the engine wire band.
(e) Install the engine wire clamp.
27. INSTALL KNOCK SENSORS
(a) Using SST, install the 2 knock sensors.
SST 09816±30010
Torque: 39 N´m (400 kgf´cm, 29 ft´lbf)
(b) Connect the 2 knock sensor connectors.
28. INSTALL NO.2 IDLER PULLEY BRACKET
Torque: 28 N´m (290 kgf´cm, 21 ft´lbf)
29. INSTALL A/C COMPRESSOR HOUSING BRACKET
Torque: 25 N´m (250 kgf´cm, 18 ft´lbf)

IG047±03
S05284
Engine Moving Control Rod
No.2 RH Engine Mounting Bracket
Generator Drive Belt
RH Front Fender Apron SealPS Pump Drive BeltGround Strap Connector
N´m (kgf´cm, ft´lbf) : Specified torque
64 (650, 47)
64 (650, 47)
52 (530, 38)
IG±10
± IGNITION (5S±FE)CRANKSHAFT POSITION SENSOR
1692 Author: Date:
CRANKSHAFT POSITION SENSOR
COMPONENTS