2000 MITSUBISHI MONTERO relay

AUTOMATIC TRANSMISSION -Troubleshooting 23-31
Code No. 36 DCC solenoid valve systemProbable cause
If the drive terminal voltage of the DCC solenoid valve is 3.0 V or less, it is
judged that there is ashort-circuit oropencircuit in the DCC solenoid valve, and
code No. 36 is output.
The transmission will be fixed in 3rd as a fail-safe measure, and the N range
indicator will flash at a rate of 1 Hz.DMalfunction of DCC solenoid valve
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
LRefer to the Transmission Workshop Manual.
NO
YES
OK
MUT-
IISelf-Diag Code
DIs code No. 54 output?Code No. 54 - A/T control relay system check
(Refer to P.23-103.)
OKNG
Transient malfunction
(Refer to GROUP 00 - Points to Note for Transient
Malfunctions.)MUT-
IIActuator Test
DNo. 6 DCC solenoid valve
OK:Sound of operation can be heard
OK
Check the following connectors:<6G7> D-122,<4M4>D-107
OK
NG
NG
Replace the engine-A/T-ECU or A/T-ECU.
Repair
OK
NG
Check the trouble symptoms.
OK
NG
Check the following connectors:E-113, D-12
NG
Repair
Check the harness between the solenoid valve assembly and
the A/T control relay, and repair if necessary.
Check the following connectors:<6G7> D-122, E-113, D-12,
<4M4> D-107, E-113,D-12NG
NG
RepairCheck the following connector:C-04
Replace the DCC solenoid valve.
L
OK
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the solenoid
valve side.
D<4M4>Resistance between terminal 7 and 10
OK:2.7 - 3.4
W
OK
Measure at engine-A/T-ECU connector D-122 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals.
DIgnition switch: ON
D<6G7> Voltage between terminal 107 and earth
D<4M4> Voltage between terminal 15 and earth
OK:System voltage
DCheck the harness between the solenoid valve assembly
and the engine-A/T-ECU, and repair if necessary. <6G7>
DCheck the harness between the solenoid valve assembly
and the A/T-ECU, and repair if necessary.<4M4>
DCheck the harness between the solenoid valve assembly
and the A/T control relay, and repair if necessary.RepairNG
Measure at solenoid valve assembly connector C-04.
DDisconnect the connector and measure at the harness
side.
DIgnition switch: ON
DVoltage between terminal 10 and earth
OK:System voltage


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-45
Code No. 54 A/T control relay systemProbable cause
If the A/T control relay voltage is less than 7 V after the ignition switch is turned
to the ON position, it is judged that there is ashort-circuit to earth oropen
circuit in the A/T control relay, and code No. 54 is output.
The transmission will be fixed in 3rd as a fail-safe measure, and the N range
indicator will flash at a rate of 1 Hz.DMalfunction of A/T control relay
DMalfunction of harness or connector
DMalfunction of engine-A/T-ECU <6G7>
DMalfunction of A/T-ECU<4M4>
A/T control relay check
(Refer to P.23-103.)Replace
Transient malfunction
(Refer to GROUP 00 - Points to
Note for Transient Malfunctions.)
OK NG
Check the following connectors:
<6G7> D-120,<4M4>D-109 OK OKNG
Repair OK Repair
Check the following connector: drive vehicles> A-04, vehicles> D-145 NG
(1)NG
(2)NG
NG
Measure at engine-A/T-ECU
connector D-120 <6G7>, or at
A/T-ECU connector D-109 <4M4>.
DMeasure at the ECU terminals.
D<6G7> Voltage between terminal
50 and earth
D<4M4> Voltage between terminal
71 and earth
OK:System voltage
Replace the engine-A/T-ECU or
A/T-ECU.NGCheck the trouble symptoms.
OKMUT-
IIService Data
DNo. 54 A/T control relay
OK:System voltage
(3)NG
OK
Measure at A/T control relay
connector D-12.
DDisconnect the relay and
measure at the connector side.
(1) Voltage between terminal 1 and
earth
OK:System voltage
(2) Resistance between terminal 2
and earth
OK:2
Wor less
(3) Voltage between terminal 4 and
earth
(Ignition switch: ON)
OK:System voltage
OK
Check the following connector:D-12Replace NG
Check the harness between the A/T
control relay and the battery.
NG
OKRepair
Check the following connector:D-14
Check the harness between the A/T
control relay and body earth.
Repair OKNG
NG
DCheck the harness between the
A/T control relay and the
engine-A/T-ECU. <6G7>
DCheck the harness between the
A/T control relay and the
A/T-ECU, and repair if necessary.
<4M4>
DCheck the harness between the
A/T control relay and the
engine-A/T-ECU. <6G7>
DCheck the harness between the
A/T control relay and the
A/T-ECU.<4M4>Measure at engine-A/T-ECU
connector D-121 <6G7>, or at
A/T-ECU connector D-107 <4M4>.
DMeasure at the ECU terminals.
DIgnition switch: ON
D<6G7> Voltage between terminals
77, 89 and earth
D<4M4> Voltage between terminals
2, 3 and earth
OK:System voltage
OK
DCheck the harness between the
A/T control relay and the battery.
DCheck the harness between the
A/T control relay and the
engine-A/T-ECU. <6G7>
DCheck the harness between the
A/T control relay and the
A/T-ECU, and repair if necessary.
<4M4> NGCheck the following connectors:
<6G7> D-121,<4M4>D-107OK
NG
Repair


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-62
Data
list No.Normal condition Inspection conditions Check item
36DCC solenoid
valve duty ratioShift range: 2ndDriving at 30 km/h in
2 range, then fully
close accelerator.70% - 90% -to- 0%
Driving at 50 km/h in
4th70% - 90%
52Damper clutch slip
amountShift range: 2ndDriving at 30 km/h in
2 range, then fully
close accelerator.- 300 - 100 r/min or 100 - 300 r/min
Driving at a constant
speed of 50 km/h in
4th- 10 - 10 r/min
54Control relay out-
put voltageIgnition switch:
OFFIgnition switch: ON10 - 12 V
61Inhibitor switchIgnition switch: ON
Engine: StoppedSelector lever posi-
tion: PP
Engine: Stopped
Selector lever posi-
tion: RR
Selector lever posi-
tion: NN
Selector lever posi-
tion: DD
63Shift positionSelector lever posi-
tion:
Sports modeDriving at a constant
speed of 10 km/h in
1st1st
Driving at a constant
speed of 30 km/h in
2nd2nd
Driving at a constant
speed of 50 km/h in
3rd3rd
Driving at a constant
speed of 50 km/h in
4th4th
Driving at a constant
speed of 70 km/h in
5th5th
65Dual pressureEngine: IdlingA/C switch: ONON
switchA/C switch: OFFOFF
66OD-OFFsignal
control is operatingWhile driving on a
level roadOFF
auto-cruise control
system>While climbing an
inclineON


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-63
Data
list No.Normal condition Inspection conditions Check item
67Select switchIgnition switch: ON
Engine: Stopped(Data List No. )No.
67No.
68No. 69
Engine: Stopped
Selector lever posi-
tion: DOFFOFFOFF
68Upshift switchSelector lever opera-
tion: Sports mode
selectedONOFFOFF
69Downshift switchSelector lever opera-
tion: Lever moved to
upshift position and
heldONONOFF
Selector lever opera-
tion: Lever moved to
downshift position
and heldONOFFON
73Target effective en-
gine pressure
<6G7>Engine: Idling
Selector lever posi-
tion: NAccelerator pedal:
fully closed to de-
pressedData changes.
754LLc switchIgnition switch: ON
Engine: StoppedTransfer lever posi-
tion: 4LLcON
Transfer lever posi-
tion:
Other than the aboveOFF
76Theoretical effec-
tive engine pres-
sure
<4M4>Engine: Idling
Selector lever posi-
tion: NAccelerator pedal:
fully closed to de-
pressedData changes.
ACTUATOR TEST TABLE
Item No.Check itemTest contentsInspection conditionsNormal condition
1LR solenoid valveThe solenoid valveIgnition switch: ONThe sound of opera-
2UD solenoid valvespecified by the MUT-Selector lever posi-tion should be heard
32nd solenoid valve
IIis driven at 50%
duty for 5 seconds. Notion: P
Engine: Stoppedwhen the solenoid
valve is driven.
4OD solenoid valveother solenoid valvesEngine: Stopped
Throttle (accelerator)
5RED solenoid valve
are energised.Opening angle volt-
6DCC solenoid valveage: Less than 1 V
<6G7>,
71st shift indicator lampThe indicator lamp for
<6G7>,
less than 1.2 V <4M4>
The shift indicator
82nd shift indicator lampthe shift stage speci-The fail-safe function
should not be operat-lamp illuminates.
93rd shift indicator lamp
fied by the MUT-II
illuminates for 3 sec-should not be operat-
ing.
104th shift indicator lamponds.
115th shift indicator lamp
12A/T control relayThe A/T control relay
turns off for 3 sec-
onds.Data List No. 54
(1) During test: 0 V
(2) Normal: System voltage
(V)


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troubleshooting 23-68
Ter-
minal
No.Standard value Inspection conditions Check item
54Input communication withEngine: IdlingOther than 0 V
engine-ECUSelector lever position: D
55Inhibitor switch PIgnition switch: ON
Selector lever position: PSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
56Inhibitor switch NIgnition switch: ON
Selector lever position: NSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
57Select switchIgnition switch: ON
Selector lever operation: Sports modeSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
58Downshift switchIgnition switch: ON
Selector lever position: Downshifted in Sports mode
and lever heldSystem voltage
Ignition switch: ON
Selector lever operation: Other than the above0V
59Stop lamp switchIgnition switch: ON
Brake pedal DepressedSystem voltage
Ignition switch: ON
Brake pedal Released0V
62DIR solenoid valveEngine: Idling
Shift range: ParkSystem voltage
Engine: Idling
Shift range: 2nd7-9V
65Wide open throttle switchAccelerator pedal: Released4.5 - 5.5 V
Accelerator pedal: DepressedLess than 0.4 V
66Inhibitor switch RIgnition switch: ON
Selector lever position: RSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
67Inhibitor switch DIgnition switch: ON
Selector lever position: DSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
68Upshift switchIgnition switch: ON
Selector lever position: Upshifted in Sports mode and
lever heldSystem voltage
Ignition switch: ON
Selector lever position: Other than the above0V
69Vehicle speed sensorWhen stopped0V
When starting to drive forward slowly.0 V and 5 V alter-
nates
71A/T control relayIgnition switch: OFF0V
Ignition switch: ON10 - 12 V
72EarthIgnition switch: ON0V


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-72
INSPECTION PROCEDURES CLASSIFIED BY DIAGNOSIS CODE
Code No. 11, 12 Power supply voltage systemProbable cause
Code No. 11 is output to indicate a drop in voltage if the power supply voltage drops
below 9.5 V.
Code No. 12 is output to indicate overvoltage if the power supply voltage rises above
18 V.DMalfunction of ignition switch
DMalfunction of harness or connector
DMalfunction of transfer-ECU
NG OK
OK
Repair NG
Replace
NG
Ignition switch single part check
(Refer to GROUP 54 - Ignition Switch.)
Check the following connectors: D-208,
D-210, D-32, E-115, E-105, D-208, D-210,
E-115, E-105
Repair
Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.)
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DIgnition switch: ON
DVoltage between terminal 13 and earth
OK:System voltage
Check the harness between the ignition switch and the
transfer-ECU, and repair if necessary.
OK
Replace the transfer-ECU. OKOK NG
NGCheck the trouble symptoms.
MUT-
IIData List
DNo. 9 Ignition voltage
OK:Refer to P.23-87 (Data List Chart).
NG
Check the following connector:E-105
Code No. 13 Main relay (inside ECU) systemProbable cause
Code No. 13 is output to indicate a relay malfunction if the voltage rises to 6 V
or higher when the relay is off, or if it drops below 6 V when the relay is on.DMalfunction of transfer-ECU
Replace the transfer-ECU.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-84
Code No. 41 Shift actuator system (open circuit or
short-circuit)Probable cause
Code No. 41 is output to indicate anopencircuit or short-circuit in the shift
actuator if the transfer-ECU terminal voltage is higher than themainrelay
voltage (90% of the rated voltage), or lower than themainrelay voltage (10% of
the rated voltage) when shift operation is notbeingcarried out.DMalfunction of shift actuator
DMalfunction of harness or connector
DMalfunction of transfer-ECU
LRefer to the Transmission Workshop Manual.
NG
NG
NG
MUT-
IIData List
DNo. 12 Shift actuator voltage
OK:Refer to P.23-87 (Data List Chart).Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.) OK
OK NG
Check the harness between the shift actuator and the
transfer-ECU, and repair if necessary.Repair
OKOK
OK
OK
NG
NG
Replace the transfer-ECU.
Check the following connectors:C-11, E-105Measure at shift actuator connector C-11.
DDisconnect the connector and measure at the harness
side.
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 2.
DVoltage between terminals 2 and earth
OK:System voltage
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 3.
DVoltage between terminal 1 and earth
OK:System voltage
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 2.
DVoltage between terminal 1 and earth
OK:System voltage
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 3.
DVoltage between terminals 3 and earth
OK:System voltage
Repair NG
Check the following connector:C-11Repair
Replace the shift actuator.
L
Check the following connector:E-105
Check the trouble symptoms.


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk

AUTOMATIC TRANSMISSION -Troublehshooting II>23-85
Code No. 42 Shift actuator system (short-circuit)Probable cause
Code No. 43 Shift actuator system (open circuit)
Code No. 42 is output to indicate a short-circuit in the shift actuator if the shift
actuator current is +1 A greater than the target value while the actuator isbeing
driven.
Code No. 43 is output to indicate anopencircuit in the shift actuator if themain
relay voltage is lower than 6 V, or the shift actuator current is 0.1 A lower than
the actual value while the actuator isbeing driven.DMalfunction of shift actuator
DMalfunction of harness or connector
DMalfunction of transfer-ECU
LRefer to the Transmission Workshop Manual.
NG
NG
MUT-
IIData List
DNo. 10 Shift actuator voltage
OK:Refer to P.23-87 (Data List Chart).Transient malfunction (Refer to GROUP 00 - Points to Note
for Transient Malfunctions.) OK
OK NG
Check the harness between the shift actuator and the
transfer-ECU, and repair if necessary.Repair
Check the following connector:E-105
OK OK
NG
OK
OK
NG
NG
Check the trouble symptoms.
Replace the transfer-ECU.
Check the following connectors:C-11, E-105Measure at shift actuator connector C-11.
DDisconnect the connector and measure at the harness
side.
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 2.
DVoltage between terminals 2 and earth
OK:System voltage
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 3.
DVoltage between terminal 1 and earth
OK:System voltage
Measure at transfer-ECU connector E-105
DMeasure at ECU terminals.
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 2.
DVoltage between terminal 1 and earth
OK:System voltage
DDrive the shift actuator in accordance with MUT-
IIactuator
test No. 3.
DVoltage between terminals 3 and earth
OK:System voltage
Repair NG
Check the following connector:C-11Repair
Replace the shift actuator.
L


www.WorkshopManuals.co.uk


Purchased from www.WorkshopManuals.co.uk