1999 SUBARU LEGACY light

B6M0238
2. HAZARD SWITCH
Move hazard switch to each position and check
continuity between terminals.
B6M0834A
8. Back-up Light
A: REMOVAL AND INSTALLATION
1. BACK-UP LIGHT
Remove and install rear finisher. [W6A2].>
2. BACK-UP LIGHT SWITCH (MT MODEL)
Remove and install back-up light switch. 3-1 [W2B1].> (AWD), (FWD)
3. INHIBITOR SWITCH (AT MODEL)
Remove and install inhibitor switch (R position
switch).
B: INSPECTION
1. INHIBITOR SWITCH (AT MODEL)
Inspect inhibitor switch.
15
[W8B1]6-2SERVICE PROCEDURE
8. Back-up Light

9. Room Light and Door Switch
A: REMOVAL AND INSTALLATION
1. ROOM LIGHT
1) Pry room light lens off using a screwdriver.
2) Remove screws which secure room light body.
B6M0068
3) Remove room light body while disconnecting
connector.
4) Installation is in the reverse order of removal.
2. TRUNK ROOM LIGHT (SEDAN)
1) Turn trunk room light body by hand and remove
it from rear shelf panel.
2) Disconnect connector of trunk room light.
B6M0345A
3) Installation is in the reverse order of removal.
3. LUGGAGE ROOM LIGHT (WAGON)
1) Pry luggage room light lens off using a screw-
driver.
2) Remove screws which secure luggage room
light body.3) Remove luggage room light body while discon-
necting connector.
B6M0069
4) Installation is in the reverse order of removal.
4. DOOR SWITCH
1) Remove rubber boot of door switch.
2) Remove screw which secures door switch to
body.
B6M0070A
3) Remove door switch while disconnecting con-
nector.
4) Installation is in the reverse order of removal.
5. TRUNK ROOM LIGHT SWITCH (SEDAN)
Remove and install trunk room light switch which is
installed in trunk lid lock.
6. LUGGAGE ROOM LIGHT SWITCH
(WAGON)
Remove and install luggage room light switch
which is installed in rear gate lock. [W3A2].>
B: INSPECTION
1. DOOR SWITCH
Move switch and check continuity between termi-
nal of door switch and switch body.
16
6-2[W9A1]SERVICE PROCEDURE
9. Room Light and Door Switch

B6M0835A
2. TRUNK ROOM LIGHT SWITCH (SEDAN)
Move switch and check continuity between termi-
nals of trunk room light switch.
B6M0836A
3. LUGGAGE ROOM LIGHT SWITCH
(WAGON)
Move switch and check continuity between termi-
nals of luggage room light switch.
B6M0837A
17
[W9B3]6-2SERVICE PROCEDURE
9. Room Light and Door Switch

10. Spot Light
A: REMOVAL AND INSTALLATION
1. SPOT LIGHT AND SWITCH
1) Pry spot light lens off using a screwdriver.
2) Remove screws which secure spot light body.
B6M0346
3) Remove spot light body while disconnecting
connector(s).
4) Installation is in the reverse order of removal.
B: INSPECTION
1. SPOT LIGHT SWITCH
Move switch and check continuity between termi-
nal of spot light switch connector and steel plate as
shown.
B6M0838A
11. Front Wiper and Washer
A: ADJUSTMENT
1) Turn the wiper switch to OFF position.
2) Adjust blades in original position as shown in
figure by changing wiper arm installation.
B6M0907A
B: REMOVAL AND INSTALLATION
1. BLADE
1) Pull out blade following the arrow direction from
arm while pushing up locking clip.
B6M0107A
2) Installation is in the reverse order of removal.
2. WIPER ARM
1) Open front hood.
2) Remove cap of wiper arm installation nut.
3) Remove the nut which secures wiper arm.
G6M0118
4) Remove wiper arm.
5) Installation is in the reverse order of removal.
18
6-2[W10A1]SERVICE PROCEDURE
10. Spot Light

10. Spot Light
A: REMOVAL AND INSTALLATION
1. SPOT LIGHT AND SWITCH
1) Pry spot light lens off using a screwdriver.
2) Remove screws which secure spot light body.
B6M0346
3) Remove spot light body while disconnecting
connector(s).
4) Installation is in the reverse order of removal.
B: INSPECTION
1. SPOT LIGHT SWITCH
Move switch and check continuity between termi-
nal of spot light switch connector and steel plate as
shown.
B6M0838A
11. Front Wiper and Washer
A: ADJUSTMENT
1) Turn the wiper switch to OFF position.
2) Adjust blades in original position as shown in
figure by changing wiper arm installation.
B6M0907A
B: REMOVAL AND INSTALLATION
1. BLADE
1) Pull out blade following the arrow direction from
arm while pushing up locking clip.
B6M0107A
2) Installation is in the reverse order of removal.
2. WIPER ARM
1) Open front hood.
2) Remove cap of wiper arm installation nut.
3) Remove the nut which secures wiper arm.
G6M0118
4) Remove wiper arm.
5) Installation is in the reverse order of removal.
18
6-2[W10A1]SERVICE PROCEDURE
10. Spot Light

B: BULB REPLACEMENT
B6M0761C
(1) Tachometer and temperature
gauge illumination
(2) Oil pressure
(3) CHECK ENGINE (Malfunction
Indicator Light)
(4) Tachometer illumination
(5) Turn signal (RH)
(6) Headlight beam(7) Door open (Front-Right)
(8) Seat belt
(9) Door open (Front-Left)
(10) Door open (Rear-Right)
(11) Door open (Rear-Left)
(12) Rear gate open (Wagon)
(13) Turn signal (LH)
(14) Speedometer illumination(15) Speedometer and fuel gauge
illumination
(16) Low fuel
(17) Charge
(18) Brake fluid level/parking brake
(19) FWD
(20) AT oil temperature
(21) ABS
28
6-2[W14B0]SERVICE PROCEDURE
14. Combination Meter

16. Horn and Cigarette Lighter
A: REMOVAL AND INSTALLATION
1. HORN
1) Open the engine hood.
2) Disconnect connector of horn.
3) Remove the horn.
4) Installation is in the reverse order of removal.
Tightening torque:
18
±5 N´m (1.8±0.5 kg-m, 13.0±3.6 ft-lb)
CAUTION:
After installing horn, connect connector, fit
firmly wiring harness to prevent from discon-
necting due to vibration.
B6M0349
2. HORN SWITCH (HORN PAD)
1) Remove screw which secures horn switch
(steering pad) to the base of steering wheel.
B6M0124
2) Remove horn switch (steering pad) from steer-
ing wheel while disconnecting connector.
3) Installation is in the reverse order of removal.
3. CIGARETTE LIGHTER
1) Remove center panel from instrument panel.

2) Disconnect connector from cigarette lighter.
3) Turn illumination socket 45É counterclockwise
and remove it.4) Loosen nut, and then remove cigarette lighter
body.
B6M0350A
5) Installation is in the reverse order of removal.
CAUTION:
IAlign socket with cutout portion of instru-
ment panel during installation.
IIn case of replacing cigarette lighter, use
genuine part only and always replace both plug
and socket combination.
B: INSPECTION
1. HORN SWITCH
Ensure that horn switch is free from the following
defects:
(1) Burned or shorted contacts
(2) Broken or weak spring
(3) Damaged harness
(4) Worn or corroded mating surface of horn plate
2. HORN RELAY
Check continuity between terminals as indicated in
table, when connecting the battery to terminals No.
1 and No. 2.
When current flows. Between termi-
nals No. 2 and
No. 3Continuity
exists.
When current does not
flow.Between termi-
nals No. 2 and
No. 3Continuity does
not exist.
Between termi-
nals No. 1 and
No. 2Continuity
exists.
B6M0126A
30
6-2[W16A1]SERVICE PROCEDURE
16. Horn and Cigarette Lighter

3. HORN
Make sure that horn sounds when battery voltage
is applied between connector terminal and horn
body.
B6M0127
4. CIGARETTE LIGHTER
1) Remove plug. Then, check element's contact
for wear, and element for accumulation of ashes,
foreign particles, etc.
2) Check element for discontinuity.
3) Remove socket and clean element. Then,
check for wear or foreign particles on element's
contact and mating surface.
4) Ensure that cigarette lighter returns within 20
seconds after it is turned to ON.
17. Power Window
A: REMOVAL AND INSTALLATION
1. MAIN SWITCH, SUB SWITCH AND
POWER WINDOW MOTOR
Remove and install power window main switch,
sub switch and motor.
NOTE:
To remove the power window motor, it is necessary
to disassemble the door component parts.
B: INSPECTION
1. MAIN SWITCH
Set power window main switch to each position
and check continuity between terminals.
B6M0128A
31
[W17B1]6-2SERVICE PROCEDURE
17. Power Window