1999 SUBARU LEGACY door lock

8. Lateral Link
A: REMOVAL
H4M1067C
(1) Crossmember
(2) Adjusting bolt
(3) Stabilizer link
(4) Rear lateral link
(5) Bushing (C)
(6) Bushing (A)
(7) Front lateral link(8) Bushing (B)
(9) Washer
(10) Cap (Protection)
(11) Trailing link
(12) Self-locking nutTightening torque: N´m (kg-m, ft-lb)
T1:
44±6 (4.5±0.6, 32.5±4.3)
T2:98±15 (10.0±1.5, 72±11 )
T3:11 3±15 (11.5±1.5, 83±11
T4:137±20 (14.0±2.0, 101±14)
1) Loosen wheel nuts. Lift-up vehicle and remove
wheel.
2) Remove stabilizers link from lateral link.
3) Remove ABS sensor harness from trailing link.
(ABS equipped models.)
4) Remove bolt securing trailing link to housing.
B4M0573A
5) Remove bolts which secure lateral link assem-
bly to rear housing.
6) Remove crossmember reinforcement lower
from crossmember. (4 door model only)
29
[W8A0]4-1SERVICE PROCEDURE
8. Lateral Link

3. Front and Rear Drive Shafts
A: REMOVAL
1. FRONT DRIVE SHAFT
1) Disconnect ground cable from battery.
2) Jack-up vehicle, support it with safety stands
(rigid racks), and remove front wheel cap and
wheels.
3) Unlock axle nut.
4) While depressing brake pedal, remove axle nut
using a socket wrench.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
5) Disconnect stabilizer link from transverse link.
6) Disconnect transverse link from housing.
7) Remove spring pin which secures transmission
spindle to DOJ/SFJ.
CAUTION:
Use a new spring pin.
G4M0279
8) Remove front drive shaft assembly. If it is hard
to remove, use ST1 and ST2.
ST1 926470000 AXLE SHAFT PULLER
ST2 927140000 PLATE
CAUTION:
IBe careful not to damage oil seal lip when
removing front drive shaft.
IWhen front drive shaft is to be replaced, also
replace inner oil seal.
G4M0216
2. REAR DRIVE SHAFT
1) Disconnect ground cable from battery.
2) Lift-up vehicle, and remove rear wheel cap and
wheels.
CAUTION:
Be sure to loosen and retighten axle nut after
removing wheel from vehicle. Failure to follow
this rule may damage wheel bearings.
3) Unlock axle nut.
4) Loosen axle nut using a socket wrench.
CAUTION:
Do not remove axle nut.
5) Remove ABS sensor clamps and parking brake
cable bracket.
6) Remove bolts which secure lateral link assem-
bly to rear housing.
CAUTION:
Discard old self-locking nut. Replace with a
new one.
7) Remove bolts which secure trailing link assem-
bly to rear housing.
CAUTION:
Discard old self-locking nut. Replace with a
new one.
8) Remove crossmember reinforcement lower
from crossmember (4 door model only).
9) Remove DOJ from rear differential using ST.
(Except 2200 cc AT vehicles)
ST 28099PA100 DRIVE SHAFT REMOVER
CAUTION:
Do not remove circlip attached to inside of dif-
ferential.
G4M0994
22
4-2[W3A1]SERVICE PROCEDURE
3. Front and Rear Drive Shafts

6) Insert DOJ spline end into bore of side oil seal,
and remove ST.
CAUTION:
Do not allow DOJ splines to damage side oil
seal.
ST 28099PA090 SIDE OIL SEAL PROTEC-
TOR
B4M0550A
7) Align DOJ and differential splines.
8) Push housing to insert DOJ into differential.
NOTE:
Make sure DOJ is inserted properly.
G3M0050
9) Connect crossmember reinforcement lower to
crossmember (4 door model only).
10) Connect rear housing assembly to trailing link
assembly, and tighten self-locking nut.
Tightening torque:
11 3
±15 N´m (11.5±1.5 kg-m, 83±11 ft-lb)
11) Connect rear housing assembly to lateral link
assembly, and tighten self-locking nut.
Tightening torque:
137
±20 N´m (14±2 kg-m, 101±14 ft-lb)
12) Install stabilizer bracket.
13) While depressing brake pedal, tighten axle nut
using a socket wrench.
Tightening torque:
186
±20 N´m (19±2 kg-m, 137±14 ft-lb)
CAUTION:
IUse a new axle nut.
IAlways tighten axle nut before installing
wheel on vehicle. If wheel is installed and
comes in contact with ground when axle nut is
loose, wheel bearings may be damaged.
IBe sure to tighten axle nut to specified
torque. Do not overtighten it as this may dam-
age wheel bearing.
14) After tightening axle nut, lock it securely.
35
[W3E2]4-2SERVICE PROCEDURE
3. Front and Rear Drive Shafts

assembly, and tighten self-locking nut.
9) Connect stabilizer link to lateral link.
10) Install crossmember reinforcement lower to
crossmember (4 door model only).
11) Install ABS sensor clamps and parking brake
cable bracket.6. Full Wheel Cap
A: REMOVAL
Pry off the full wheel cap with a wheel cap remover
inserted between openings in the cap.
B4M0051
B: INSTALLATION
Align the valve hole in the wheel cap with the valve
on the wheel and secure the wheel cap by tapping
four points by hand.
38
4-2[W6A0]SERVICE PROCEDURE
6. Full Wheel Cap

assembly, and tighten self-locking nut.
9) Connect stabilizer link to lateral link.
10) Install crossmember reinforcement lower to
crossmember (4 door model only).
11) Install ABS sensor clamps and parking brake
cable bracket.6. Full Wheel Cap
A: REMOVAL
Pry off the full wheel cap with a wheel cap remover
inserted between openings in the cap.
B4M0051
B: INSTALLATION
Align the valve hole in the wheel cap with the valve
on the wheel and secure the wheel cap by tapping
four points by hand.
38
4-2[W6A0]SERVICE PROCEDURE
6. Full Wheel Cap

6. Rear Gate and Glass
B5M0056B
(1) Rear gate
(2) Key cylinder
(3) Outer handle
(4) Door lock actuator
(5) Striker
(6) Latch
(7) Glass pin(8) Glass
(9) Buffer
(10) Stopper
(11) Gas stay
(12) Hinge
(13) Rear gate handleTightening torque: N´m (kg-m, ft-lb)
T1:
4.4±1.5 (0.45±0.15, 3.3±1.1)
T2:7.4±2.0 (0.75±0.2, 5.4±1.4)
T3:13±3 (1.3±0.3, 9.4±2.2)
T4:14±4 (1.4±0.4, 10.1±2.9)
T5:25±5 (2.5±0.5, 18.1±3.6)
8
5-2[C600]COMPONENT PARTS
6. Rear Gate and Glass

7. Door Lock Assembly
A: FRONT DOOR
B5M0057B
(1) Holder remote
(2) Inner remote ASSY
(3) Door outer handle
(4) Striker
(5) Door latch(6) Switch ASSY
(7) Auto-door lock actuator
(8) Bell crank
(9) Rod holderTightening torque: N´m (kg-m, ft-lb)
T1:
6.4±2.0 (0.65±0.2, 4.7±1.4)
T2:7.4±2.0 (0.75±0.2, 5.4±1.4)
T3:14±4 (1.4±0.4, 10.1±2.9)
9
[C7A0]5-2COMPONENT PARTS
7. Door Lock Assembly

B: REAR DOOR
B5M0058B
(1) Door outer handle
(2) Door latch
(3) Door lock actuator
(4) Striker
(5) Rod holder(6) Holder remote
(7) Inner remote ASSYTightening torque: N´m (kg-m, ft-lb)
T1:
6.4±2.0 (0.65±0.2, 4.7±1.4)
T2:7.4±2.0 (0.75±0.2, 5.4±1.4)
T3:14±4 (1.4±0.4, 10.1±2.9)
10
5-2[C7B0]COMPONENT PARTS
7. Door Lock Assembly