1999 NISSAN PRIMERA washer fluid

Removal and Installation
WIPER ARM
1. Prior to wiper arm installation, turn on wiper switch to oper-
ate wiper motor and then turn it off (Auto Stop).
2. Lift the blade up and then set it down onto glass surface. Set
the blade center before tightening nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper
motor and then turn it off.
4. Ensure that wiper blade stops in the correct position.

Tighten windshield wiper arm nut to specified torque.
:13-18N·m (1.4 - 1.8 kg-m, 10 - 13 ft-lb)

Before reinstalling wiper arm, clean up the pivot area as
illustrated. This will reduce possibility of wiper arm
looseness.
Washer Nozzle Adjustment

Adjust washer nozzle with suitable tool as shown in the fig-
ure at left.
Adjustable range: ±10°(In any direction)
Wagon60 (2.4)
170.3 (6.7)
Unit: mm (in) Sedan
Molding
edge
Hatchback
Back
door
side
66 (2.6)
YEL456B
SEL024J
NEL314 Suitable tool
Max. 10°
Nozzle hole bore diameter
1.0 mm (0.039 in)
REAR WIPER AND WASHER
EL-197

Washer Tube Layout
Check Valve

A check valve is provided in the washer fluid line. Be careful
not to connect check valve to washer tube in the wrong
direction.
NEL557 Nozzle
Check valve
Rear washer tube Sedan and
Hatchback
To reservoir tank
Check valve
Nozzle (Sedan)Wagon
Rear washer tube
To reservoir tank
Check valve Nozzle
SEL411H From res-
ervoir
tankCheck valveTo
nozzle Sedan
NEL552 From res-
ervoir
tankCheck valveTo
nozzle Hatchback and wagon
REAR WIPER AND WASHER
EL-199

Washer Tube Layout
Check Valve

A check valve is provided in the washer fluid line. Be careful
not to connect check valve to washer tube in the wrong
direction.
NEL555 To reservoir tankWasher nozzle
Check valve
NEL554 From res-
ervoir
tankCheck valve
To
nozzle
To
nozzle
HEADLAMP WASHER
EL-202

lBefore starting repairs which do not require battery power:
Turn off ignition switch.
Disconnect the negative battery terminal.
lTo prevent serious burns:
Avoid contact with hot metal parts.
Do not remove the radiator cap when the engine is hot.
lBefore servicing the vehicle:
Protect fenders, upholstery and carpeting with appropriate
covers.
Take care that keys, buckles or buttons do not scratch paint.
lClean all disassembled parts in the designated liquid or sol-
vent prior to inspection or assembly.
lReplace oil seals, gaskets, packings, O-rings, locking
washers, cotter pins, self-locking nuts, etc. with new ones.
lReplace inner and outer races of tapered roller bearings and
needle bearings as a set.
lArrange the disassembled parts in accordance with their
assembled locations and sequence.
lDo not touch the terminals of electrical components which
use microcomputers (such as ECMs).
Static electricity may damage internal electronic compo-
nents.
lAfter disconnecting vacuum or air hoses, attach a tag to
indicate the proper connection.
lUse only the fluids and lubricants specified in this manual.
lUse approved bonding agent, sealants or their equivalents
when required.
lUse tools and recommended special tools where specified
for safe and efficient service repairs.
lWhen repairing the fuel, oil, water, vacuum or exhaust
systems, check all affected lines for leaks.
lDispose of drained oil or solvent used for cleaning parts in
an appropriate manner.
SEF289H
SGI233
SGI234 Seat cover
Fender cover
PRECAUTIONS
General Precautions (Cont'd)
GI-5

Checking Refrigerant Leaks
PRELIMINARY CHECK
Perform a visual inspection of all refrigeration parts, fittings,
hoses, and components for signs of A/C lubricant leakage, dam-
age and corrosion.
PRECAUTIONS FOR HANDLING LEAK DETECTOR
When performing a refrigerant leak check, use an A/C leak
detector or equivalent. Ensure that the instrument is calibrated
and set properly per the operating instructions.
The leak detector is a delicate device. In order to use the leak
detector properly, read the operating instructions and perform
any specified maintenance.
Other gases in the work area or substances on the A/C
components, for example, anti-freeze, windshield washer
fluid, solvents and cleaners, may falsely trigger the leak
detector. Make sure the surfaces to be checked are clean.
Do not allow the sensor tip of the detector to come into
contact with any substance. This can also cause false read-
ings and may damage the detector.
1. Position probe approximately 5 mm (3/16 in) away from point
to be checked.
2. When testing, circle each fitting completely with probe.
SHA705EB A/C leak
detector
SHA707E
SHA706E
SERVICE PROCEDURESAUTO
HA-106

Evaporative emission (EVAP)
system ...............................EC-QG-25, EC-SR-27
Exhaust gas recirculation (EGR)
valve...........................................EC-QG-244, 305
Exhaust system ................................................FE-9
Exhaust system inspection ............................MA-48
Exterior ............................................................BT-31
F
FCUT - Wiring diagram ..........................EC-CD-101
F/FOG - Wiring diagram................................EL-110
Final drive (FF M/T) ...........................MT-32, 51, 71
Floor trim .........................................................BT-18
Fluid temperature sensor (A/T) .......................AT-94
Fluids..............................................................MA-16
Flywheel (clutch) .............................................CL-14
Flywheel runout..............................EM-60, 117, 177
Fog lamp, front ..............................................EL-110
Fog lamp, rear ...............................................EL-112
F/PUMP - Wiring
diagram..........................EC-QG-338, EC-SR-317
Freeze frame data ................EC-QG-38, EC-SR-50
Fresh vent door control linkage
adjustment ..................................................HA-83
FRO2 - Wiring diagram ........EC-QG-135, 154, 162,
EC-SR-147, 165, 172
FRO2/H - Wiring
diagram..........................EC-QG-168, EC-SR-177
Front axle ..........................................................FA-9
Front bumper ....................................................BT-5
Front disc brake .............................................BR-23
Front door .......................................................BT-13
Front fog lamp .......................................EL-110, 111
Front fog lamp removal and installation ...........BT-5
Front heated oxygen sensor
(HO2S) ......................................EC-QG-132, 139,
EC-SR-144, 150, 156, 162, 170
Front heated oxygen sensor (HO2S)
heater ............................EC-QG-166, EC-SR-175
Front passenger air bag .................................RS-17
Front seat ........................................................BT-40
Front seat belt ..................................................RS-3
Front suspension ............................................FA-26
Front washer .................................................EL-186
Front wiper ....................................................EL-186
FTS - Wiring diagram ............................EC-CD-105
FUEL - Wiring
diagram .........EC-QG-210, 217, EC-SR-213, 220
Fuel cut control (at no load & high
engine speed)....................EC-QG-25, EC-SR-27
Fuel cut solenoid valve ..........................EC-CD-100
Fuel filter ...............................EC-QG-29, EC-SR-31
Fuel filter replacement .......................MA-23, 33, 43
Fuel gauge ............................................EL-141, 146
Fuel injection system....................EC-QG-208, 215,
EC-SR-212, 218,
EC-CD-15, 18
Fuel injector ......................EC-QG-318, EC-SR-302
Fuel line inspection............................MA-22, 33, 43Fuel precautions ................................................GI-7
Fuel pressure check .............EC-QG-29, EC-SR-31
Fuel pressure regulator .........EC-QG-30, EC-SR-32
Fuel pressure release ...........EC-QG-29, EC-SR-31
Fuel pump .........................EC-QG-336, EC-SR-316
Fuel pump and gauge ......................................FE-7
Fuel pump relay ................EC-QG-336, EC-SR-316
Fuel system ......................................................FE-6
Fuel tank vacuum relief
valve ..................................EC-QG-26, EC-SR-28
Fuel temperature sensor .................EC-CD-17, 104
Fuse ..................................................EL-22, Foldout
Fuse block ....................................................Foldout
Fusible link ........................................EL-22, Foldout
G
Garage jack and safety stand .........................GI-47
Gauges..........................................................EL-138
Gear components (M/T) ...........................MT-16, 49
Generic scan tool (GST) .......EC-QG-66, EC-SR-78
GLOW - Wiring diagram ........................EC-CD-120
Glow plug .........................................EC-CD-15, 118
Glow relay ................................................EC-CD-15
GOVNR - Wiring diagram ........................EC-CD-79
Grille - See Exterior ........................................BT-38
Ground distribution..........................................EL-23
H
H/AIM - Wiring diagram ....................EL-87, 93, 200
Harness connector ............................................EL-6
Harness layout ..............................................EL-368
Hazard warning lamp ....................................EL-117
Headlamp..................................................EL-67, 69
Headlamp aiming control ................................EL-87
Headlamp washer .........................................EL-200
Headlining - See Roof trim .............................BT-25
Heated oxygen sensor (HO2S)
(front) ........................................EC-QG-132, 139,
EC-SR-144, 150, 156, 162, 170
Heated oxygen sensor (HO2S) heater
(front) .............................EC-QG-166, EC-SR-175
Heated oxygen sensor (HO2S) heater
(rear) ..............................EC-QG-203, EC-SR-207
Heated oxygen sensor (rear) ...............EC-QG-171,
EC-SR-180, 187,
194, 201
Heated oxygen sensor inspection ...........MA-27, 38
Heated seat .......................................BT-42, EL-234
HEATER - Wiring diagram .............................HA-40
HFC134a (R134a) system service
procedure ..................................................HA-100
HFC134a (R134a) system service tools ..........HA-8
H/LAMP - Wiring diagram ...............................EL-67
Hood..................................................................BT-5
Horn ..............................................................EL-203
HORN - Wiring diagram ................................EL-203
ALPHABETICAL INDEX
IDX-4

O
Oil cooler (engine) ....................................LC-20, 30
Oil pan (engine) ...............................EM-17, 70, 129
Oil pressure (engine)............................LC-5, 16, 27
Oil pump (engine).................................LC-5, 17, 27
Oil pump regulator valve (engine) ....................LC-7
Oil seal replacement
(engine) ................................EM-29, 84, 138, 139
On board diagnostic
system ...............................EC-QG-36, EC-SR-48
Operational check (cool box) .........................HA-24
P
Park/Neutral position
switch.............................EC-QG-313, EC-SR-298
Park/neutral position switch (A/T) ...................AT-48
Parking brake control .....................................BR-48
Parking lamp .................................................EL-100
PCV (positive crankcase
ventilation) .........................EC-QG-28, EC-SR-30
PCV system inspection............................MA-26, 36
Periodic maintenance (for Europe) ..................MA-6
PGC/V - Wiring diagram ...EC-QG-264, EC-SR-252
PHASE - Wiring diagram .......................EC-QG-240
Pilot bushing replacement - See Pilot
converter ...................................................EM-117
Piston assembly..............EM-53, 60, 110, 117, 167,
175, 176, 185, 193, 199
Piston pin inspection.............EM-54, 110, 168, 171,
185, 193, 199
Piston ring inspection ....................EM-54, 111, 168,
185, 193, 199
Piston to bore clearance........................EM-56, 174
PNP/SW - Wiring
diagram..........................EC-QG-315, EC-SR-300
POWER - Wiring diagram...............................EL-12
Power door lock ....................................EL-245, 265
Power door mirror .........................................EL-231
Power seat ....................................................EL-233
Power steering fluid level...............................MA-53
Power steering oil pressure
switch.............................EC-QG-342, EC-SR-321
Power supply routing ......................................EL-10
Power transistor......................................EC-SR-311
Power transistor & ignition coil ..............EC-SR-306
Power window ...............................................EL-236
Pre-delivery inspection.....................................MA-4
Precautions (General) .......................................GI-4
Pressure test (A/T) ..........................................AT-35
PST/SW - Wiring
diagram..........................EC-QG-343, EC-SR-322
R
Radiator ..........................................LC-9, 13, 25, 36Rear axle (disc brake type) ..............................RA-5
Rear bumper ...........................................BT-7, 9, 11
Rear combination lamp removal and
installation ...................................................BT-37
Rear disc brake ........................................BR-33, 40
Rear door ........................................................BT-14
Rear drum brake ............................................BR-44
Rear fog lamp................................................EL-112
Rear heated oxygen sensor
(HO2S) ..EC-QG-171, EC-SR-180, 187, 194, 201
Rear heated oxygen sensor (HO2S)
heater ............................EC-QG-203, EC-SR-207
Rear seat ........................................................BT-43
Rear seat belt ...................................................RS-4
Rear suspension ..............................................RA-4
Rear washer..................................................EL-193
Rear window ...................................................BT-53
Rear window defogger ..................................EL-207
Rear wiper.....................................................EL-193
Refrigerant connection precaution ...................HA-4
Refrigerant general precaution.........................HA-4
Refrigerant lines ...........................................HA-104
Refrigerant pressure
sensor....................EC-QG-299, 347, EC-SR-289
Refrigeration cycle..........................................HA-12
Removal and installation (A/T) ......................AT-116
Revolution sensor (A/T) ............................AT-61, 65
R/FOG - Wiring diagram ...............................EL-112
Roof trim .........................................................BT-25
RRO2 - Wiring
diagram.....................EC-QG-174, 183, 191, 199,
EC-SR-183, 190, 197, 203
RRO2/H - Wiring
diagram..........................EC-QG-205, EC-SR-209
S
SAE J1930 terminology list .............................GI-51
Seal - See Exterior .........................................BT-31
SEAT - Wiring diagram .................................EL-233
Seat belt inspection .......................................MA-54
Seat belt pre-tensioner ...................................RS-13
Seat belt pre-tensioner disposal ....................RS-27
Seat, front .......................................................BT-40
Self-diagnostic results ...........EC-QG-46, EC-SR-59
Shift control components (M/T) .........MT-17, 50, 74
Shock absorber (rear).....................................RA-11
Side air bag ....................................................RS-19
Side trim ..........................................................BT-18
Side window - See Rear side window ............BT-55
S/LOCK - Wiring diagram .....................EL-248, 270
Spark plug replacement...........................MA-25, 35
Speedometer ........................................EL-141, 146
Spiral cable.....................................................RS-14
Spot lamp..............................................EL-130, 131
SROOF - Wiring diagram .............................EL-230
SRS - See Supplemental Restraint
System ..........................................................RS-8
SRS - Wiring diagram ....................................RS-33
ALPHABETICAL INDEX
IDX-6

Shown below are Pre-delivery Inspection Items required for the new vehicle. It is recommended that
necessary items other than those listed here be added, paying due regard to the conditions in each
country.
Perform applicable items on each model. Consult text of this section for specifications.
UNDER HOOD engine off
Radiator coolant level and coolant hose con-
nections for leaks
Battery fluid level, specific gravity and condi-
tions of battery terminals
Drive belts tension
Fuel filter for water or dust, fuel lines and con-
nections for leaks
Engine oil level and oil leaks
Clutch and brake reservoir fluid level and fluid
lines for leaks
Windshield and rear window washer and head-
lamp cleaner reservoir fluid level
Power steering reservoir fluid level and hose
connections for leaks
ON INSIDE AND OUTSIDE
Remove front spring/strut spacer (If applicable)
Operation of all instruments, gauges, lights and
accessories
Operation of horn(s), wiper and washer
Steering lock for operation
Check air conditioner for gas leaks
Front and rear seats, and seat belts for opera-
tion
All moldings, trims and fittings for fit and align-
ment
All windows for operation and alignment
Hood, trunk lid, door panels for fit and align-
ment
Latches, keys and locks for operation
Weatherstrips for adhesion and fit
Headlamp aiming
Tighten wheel nuts (Inc. inner nuts if appli-
cable)
Tire pressure (Inc. spare tire)
Check front wheels for toe-in
Install clock/voltmeter/room lamp fuse (If appli-
cable)
Install deodorizing filter to air purifier (If appli-
cable)
Remove wiper blade protectors (If applicable)
UNDER BODY
Manual transmission/transaxle, transfer and
differential gear oil level
Brake and fuel lines and oil/fluid reservoirs for
leaks
Tighten bolts and nuts of steering linkage and
gear box, suspension, propeller shafts and
drive shafts
Tighten rear body bolts and nuts (Models with
wooden bed only)
ROAD TEST
Clutch operation
Parking brake operation
Service brake operation
Automatic transmission/transaxle shift timing
and kickdown
Steering control and returnability
Engine performance
Squeaks and rattles
ENGINE OPERATING AND HOT
Adjust idle mixture and speed (and ignition tim-
ing*1)
Automatic transmission/transaxle fluid level
Engine idling and stop knob operation (Diesel
only)
FINAL INSPECTION
Install necessary parts (outside mirror, wheel
covers, seat belts, mat, carpet or mud flaps)
Inspect for interior and exterior metal and paint
damage
Check for spare tire, jack, tools (wheel chock),
and literature
Wash, clean interior and exterior
*1: Not required on models with a direct ignition system
: Not applicable to this model.
PRE-DELIVERY INSPECTION ITEMS
MA-4