1997 RENAULT KANGOO Sheet Metal Work Workshop Manual

UPPER SIDE STRUCTURE
Sill panel reinforcement
43F
PRB4316
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the sill panel for
a side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
LIST OF JOINTS :
Sill panel closure panel
Centre pillar lower reinforcement
Body side lining
Front pillar reinforcement (identical to the centre
pillar reinforcement)
PARTS CONCERNED (thickness in mm) :
1Sill panel reinforcement 1.2
2Sill panel closure panel 1.2
3Centre pillar lower reinforcement 1.2
43-23

UPPER SIDE STRUCTURE
Sill panel reinforcement
43F
13353R1
CAA11537-1R2
A
13
CAB11539-1R3
B
12
CAB11539-1R8
C
1
2
43-24

UPPER SIDE STRUCTURE
Left hand side sill panel
43G
PRB4317
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
This part can be partially replaced (see diagram
and method below).
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning other parts will be dealt
with in the respective section.
This part may be replaced in two ways :
1 - Cut A-A (described below)
2 - Cut B-B (refer to operation N for the front pil-
lar)
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
or
LIST OF JOINTS :
Body side lining
Sill panel closure panel, rear section
Sill panel closure panel, front section
PARTS CONCERNED (thickness in mm) :
1Left hand side sill panel 0.8
2Body side lining 0.7
3Sill panel closure panel, rear section 1.2
4Sill panel closure panel, front section 1.2
43-25

UPPER SIDE STRUCTURE
Left hand side sill panel
43G
13219R
or
CAA11537-1R4
A
1
1
12
or1
2
CAV13468R3
B
2
3
or
1
2
CAS13033R5
C
1
or1
2 1
1
43-26

UPPER SIDE STRUCTURE
Left hand side sill panel
13609R
43G
or
CAS13033R7
D
1
or
CAN11691R7
E
1
2
CAE11546-2R8
F
1 2 3
CAE11546-2R8
G
1 2 4 1
43-27

UPPER REAR STRUCTURE
Rear wing panel
44A
PRB4413
INTRODUCTION
The replacement of this part is a basic operation
for a rear side impact.
In the operation described below there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective section.
For the panel version, this part may be replaced in
two ways (see cuts marked on the diagram be-
low) :
1 - complete replacement with cut A.A
2 - partial replacement with cut B.B
At the end of the section there are special details
for the glazed version and for the version with
roof flap.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with sliding door rail units and
striker plate mounting.
JOINTS WITH :
Lights mounting side panel rain channel
Body side lining
Centre pillar reinforcement
PARTS CONCERNED (thickness in mm):
1Rear wing panel (right hand side) 0.8
2Rear wing panel lining
(right hand side) 0.7
3Lights mounting side panel rain
channel 1.2
4Rear wing panel extension 1
5Side panel rain channel
upper reinforcement 1.2
6Centre rail mounting 1
7Stretcher lining 0.7
8Roof 0.7
9Centre pillar upper reinforcement 1.2
10Centre pillar reinforcement 1.2
11Sill panel rear closure panel 1.5
12Seat belt mounting reinforcement 1.2
13Roof flap rain channel 0.7
44-1

UPPER REAR STRUCTURE
Rear wing panel
44A
13226R1
or
CAS13033R1
A
11
CAI11550-2R1
B - C
1 9 2
44-2

UPPER REAR STRUCTURE
Rear wing panel
44A
13227R
CAI11550-2R1
D
1 7 2
CAQ11697R3
E
1 2
CAI11550-2R4
F
1 2
12
44-3