1997 RENAULT KANGOO Sheet Metal Work Workshop Manual

LOWER STRUCTURE
Rear end cross member
41P
PRB4136
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear end pa-
nel for a rear impact.
The side member extensions must be replaced
(11) and (12) , and must be ordered separately.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
10 - Part assembled with rear shock absorber
reinforcement
11 and 12 - Side member extension
JOINTS WITH:
Rear shock absorber reinforcement
Towing ring (left hand side)
Rear side member extension
Side panel rain channel
Side panel lining
Rear floor
Side member
PARTS CONCERNED (thickness in mm):
1Rear end cross member 1.2
2Rear shock absorber reinforcement 1
3Towing ring (left hand side) 1.5
4Rear side member extension 1.5
5Side panel rain channel 1.5
6Side panel lining 0.7
7Rear floor 0.8
8Side member 1.5
41-55

LOWER STRUCTURE
Rear end cross member
41P
13225R
CAB11539R7
A
1 6
CAB11539R7
B
1
6
CAA11536-1R3
C
1 6
CAT13327R3
D
1 3
1
2
1
2
2
41-56

LOWER STRUCTURE
Rear end cross member
41P
13221R1
CAT13327R5
E
12
1
2
CAT13328R1
F
31
CAA11538R5
G
1 7
CAH11549-1R1
H
87 1 4
1
2
4
41-57

LOWER STRUCTURE
Rear shock absorber reinforcement
41Q
PRB4137
INTRODUCTION
For a rear impact, the replacement of this part is a
complementary operation to the replacement of
the rear end panel.
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part only.
JOINTS WITH:
Rear shock absorber reinforcement
Rear end cross member
PARTS CONCERNED (thickness in mm):
1Rear shock absorber reinforcement 1
2Rear end cross member 1.2
3Towing ring (left hand side) 1.5
4Rear side member extension 1.5
41-58

LOWER STRUCTURE
Rear shock absorber reinforcement
41Q
13352R13351R1
A
CAT13327R6
B
12
CAT13327R5
23
14
41-59

LOWER STRUCTURE
Rear side member extension
41R
PRB4138
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear end
cross member .
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
Use of the repair bench is advised, to ensure that
the rear cross member is correctly geometrically
positioned.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with towing ring (left hand side).
JOINTS WITH:
Rear side member
PARTS CONCERNED (thickness in mm):
1Rear side member extension 1.5
2Rear side member 1.5
3Towing ring (left hand side) 1.5
41-60

LOWER STRUCTURE
Rear side member extension
41R
13221R2
CAA11536R7
A
1
2
CAA11538R5
B
1 2
13225R1
CAA11536R7
C
3
2
41-61

LOWER STRUCTURE
Rear side member, part section
41S
PRB4139
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of the rear end
cross member for a rear impact
This part may be replaced partially (see cut and
diagram below).
In the operation described below, there are only
descriptions of the joints specific to the part
concerned.
Information concerning the other parts will be
dealt with in the respective sections.
The repair bench must be used.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
Part assembled with :
- side member rear reinforcement
- towing ring (left hand side),
- rear side member extension .
PARTS CONCERNED (thickness in mm):
1Rear side member 1.5
13221R3
or
CAS13033R1
A
1 1 or
41-62