1997 RENAULT KANGOO Sheet Metal Work Workshop Manual

UPPER FRONT STRUCTURE
Wheel arch
42F
CAB11539-1R8
I
1
7
CAE11546R7
J
1
7 6
CAS13028R1
K
9
7
6
CAA11538R7
L
92
13005R2
42-21

UPPER FRONT STRUCTURE
Wheel arch
42F
13000R
CAA11536R8
M
1
5
CAS13024-1R3
N
4
5 1
13007R
42-22

UPPER FRONT STRUCTURE
Wheel arch
42F
13010R2
CAA11538R8
O
5
11
CAS13028R2
P
9
6 7
42-23

UPPER FRONT STRUCTURE
Plenum chamber
42G
PRB4214
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of :
- the wheel arch for a frontal impact,
- cowl side panel for a side impact.
This operation may be carried out partially (see
diagram and method below).
The Parts Department only provides chambers of
the (1) "air conditioning" type, as a result, the
closure panel must also be ordered (2).
In the following operation there are only descrip-
tions of the joints specific to the part concerned.
Information concerning other parts is dealt with
in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 Plenum chamber
Part assembled with :
- bonnet lock mounting,
- windscreen wiper motor mounting.
2 Partition closure panel.
JOINTS WITH :
Wheel arch
Injection unit and impact sensor mounting (left
hand side)
Bulkhead
Pillar lining (cowl side panel)
Windscreen aperture lower cross member
PARTS CONCERNED (thickness in mm) :
1Plenum chamber 1
2Shock absorber cup height adjuster 1
3Shock absorber cup 2
4Injection unit and impact sensor
mounting (left hand side) 2
5Bulkhead 1
6Cowl side panel (pillar lining) 1.5
7Windscreen wiper mounting 1.5
8Windscreen aperture lower cross
member 1.2
or
42-24

UPPER FRONT STRUCTURE
Plenum chamber
42G
13007-1R
CAA11536R8
A
12
CAB11540R6
B
8
7
13000R1
CAS13024R3
C
1
2
3
42-25

UPPER FRONT STRUCTURE
Plenum chamber
42G
13003-1R13013R
CAA11538R7
D
16
CAS13033R2
E
11
CAA11538R7
F
15
42-26

UPPER FRONT STRUCTURE
Plenum chamber
42G
13010R3
CAA11538R8
G
1
4
42-27

UPPER FRONT STRUCTURE
Windscreen aperture lower cross member
42H
PRB4215
INTRODUCTION
The replacement of this part is a complementary
operation to the replacement of :
- the wheel arch with the cowl side panel for a
frontal impact,
- the front pillar with lining for a side impact.
This operation may be carried out partially (see
diagram and method below).
In the following operation there are only descrip-
tions of the joints specific to the part concerned.
The Parts Department supplies the windscreen
aperture lower cross member (1) without the stee-
ring column mounting (2), which must be ordered
separately.
Information concerning other parts is dealt with
in the respective section.
COMPOSITION OF THE PART FROM THE PARTS
DEPARTMENT
1 Windscreen aperture cross member
Part assembled with :
- steering column mounting height adjus-
ter,
- lower reinforcement of windscreen aper-
ture cross member.
2 Steering mounting
Part only.
JOINTS WITH :
Bulkhead
Windscreen aperture lower cross member
Windscreen aperture lower cross member
reinforcement
Steering column mounting height adjuster
Steering column mounting
Cowl side panel (pillar lining)
Windscreen wiper mounting
PARTS CONCERNED (thickness in mm) :
1Bulkhead 1
2Windscreen aperture lower cross
member 1.2
3Windscreen aperture lower cross
member reinforcement 1.2
4Steering column mounting height
adjuster 1.5
5Steering column mounting 2
6Cowl side panel (pillar lining) 1.5
7Windscreen wiper mounting 1.5or
42-28