1997 MERCEDES-BENZ ML320 clock

265 Practical hints
Opening / closing in an emergency
Opening / closing in an emergency
Sliding / pop-up roof*
You can open or close the sliding / pop-up
r o o f m a n u a l l y s h o u l d a n e l e c t r i c a l m a l f u n c -
tion occur.
The sliding / pop-up roof drive is located
behind the cover between the front interior
lamps.
1Hexagon drive hole
2Crank
3Cover

Pry off cover3 using a flat blade
srewdriver.

Obtain crank2.

Insert crank2 through hole.

Turn crank2 clockwise to:

slide roof closed


raise roof at the rear

Turn crank2 counterclockwise to:

slide roof open


lower roof at the rear
The sliding / pop-up roof must be synchro-
nized if it has been operated manually
(
page 149).iPush crank2 upward while turning it,
to disengage the electric motor.

269 Practical hints
Replacing bulbs
High beam bulbs
1High beam headlamp cover with lock-
ing tab
Switch off the lights.

Open the hood (
page 217).

Twist cover1 counterclockwise and
remove.2Electrical connector

Pull electrical connector2 off.

Unclip the retainer springs and take out
the bulb.

Insert the new bulb so that the base lo-
cates in the recess on the holder.

Clip the retainer springs.

Plug the connector2 onto the bulb.

Align headlamp cover and click into
place.Turn signal, parking, standing and side
marker lamp bulbs
1Bulb socket

Switch off the lights.

Open the hood (
page 217).

Twist bulb socket1 counterclockwise
and pull out.

Push bulb into socket, turn counter-
clockwise and remove.

Insert new bulb in socket, push in and
twist clockwise.

Reinstall the bulb socket.


270 Practical hintsReplacing bulbs
Align headlamp cover and click into
place.
Fog lamp bulbs
1Fog lamp

Switch off the lights.

Use a suitable object (e.g. screwdriver)
to press on the release lever behind the
front panel.
Front fog lamp1 releases.

Remove fog lamp out of bumper.2Bulb socket
3Tabs

Twist bulb socket2 counterclockwise
to its end stop and pull out.

Pull bulb out of the bulb socket.

Insert new bulb in socket.

Reinstall bulb socket2.

Twist bulb socket2 clockwise to its
end stop.

Reinstall fog lamp into the bumper.
Make sure tabs3 firmly seat into the
slots of holder.
Replacing bulbs for rear lamps
Tail lamp assemblies
Switch off the lights.

Open liftgate.
1Screws
2Tail, parking and standing lamp
Fog lamp, driver’s side
3Side marker lamp
4Turn signal lamp
5Backup lamp
6Brake lamp

Remove screws1.

Remove tail lamp.


271 Practical hints
Replacing bulbs
7Tabs
Squeeze tabs7 together and remove
bulb holder.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
turn clockwise.

Reinstall bulb holder. You should hear
it engage.

Insert the tail lamp in the body, lower
edge first. Make sure it engages.

Retighten screws with washers on
them.License plate lamp
1License plate lamp
2Screws

Switch off the lights.

Loosen both screws2 and remove
lamp.

Replace the tubular lamp and reinstall
lamp.

Retighten the screws.High mounted brake lamp
1Cover
2Tab

Switch off the lights.

Squeeze both sides of cover1, fold it
forward and remove.

Press tab2 on reflector and remove
reflector.

Gently push bulb into socket, turn
counterclockwise and remove.

Insert new bulb in socket, push in and
turn clockwise.


272 Practical hintsReplacing bulbs
Insert reflector from the left so that it
engages on the right.

Position tabs of cover in slots and rein-
stall cover until properly seated.
Adjusting headlamp aim
VVertical centerline
HHeadlamp mounting high, measured
from the centerCorrect headlamp adjustment is extremely
important. To check and readjust a head-
lamp, follow the steps described:

Park the vehicle on a level surface
25 feet (7.6 m) from a vertical test
screen or wall.

Switch the headlamps on
(page 110).
If the beam does not show a beam pattern
as indicated in the figure left, then follow
the steps below:

Open hood (
page 217).
2Headlamp vertical adjustment screw
3Headlamp vertical adjustment screw

Always turn adjustment screws2
and3 simultaneously for vertical ad-
justment until the headlamp is adjust-
ed as shown1. Turn clockwise for
upward movement and counterclock-
wise for downward movement.
Graduations:
screw2: 0.50° pitch
screw3: 0.67° pitch
The left and right headlamps must be ad-
justed individually.
iHigh beam adjustments simultaneous-
ly aim the low beam.
Vehicle should have a normal trunk
load.
iIf it is not possible to obtain a proper
headlamp adjustment, have the system
checked at your authorized
Mercedes-Benz Light Truck Center.


276 Practical hintsFlat tireRemoving the wheel
Unscrew and remove all wheel bolts.

Remove the remaining bolts.

Grip the wheel from the sides and re-
move it.
Mounting the new wheel

Clean contact surfaces of wheel and
wheel hub.

Install spare wheel on wheel hub.

Insert wheel bolts and tighten them
slightly.Lowering the vehicle

Lower vehicle by turning crank coun-
terclockwise until vehicle is resting ful-
ly on its own weight.

Remove the jack.
!Do not place wheel bolts in sand or dirt.
This could result in damage to the bolt
and wheel hub threads.!To avoid paint damage, place wheel flat
against hub and hold it there while in-
stalling first wheel bolt.
Warning!
G
Always replace wheel bolts that are dam-
aged or rusted.
Never apply oil or grease to wheel bolts.
Damaged wheel hub threads should be re-
paired immediately. Do not continue to drive
under these circumstances! Contact an au-
thorized Mercedes-Benz Light Truck Center
or call Roadside Assistance.
Incorrect wheel bolts or improperly tight-
ened wheel bolts can cause the wheel to
come off. This could cause an accident.
Make sure to use the correct wheel bolts.
Warning!
G
Use only genuine equipment
Mercedes-Benz wheel bolts. Other wheel
bolts may come loose.
Do not tighten the wheel bolts when the ve-
hicle is raised. Otherwise the vehicle could
tip over.

280 Practical hintsBattery
Batteries contain materials that can harm
the environment if disposed of improperly.
Large 12-volt storage batteries contain
lead. Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
iThe following procedures must be car-
ried out following any interruption of
battery power (e.g. due to reconnec-
tion):

Set the clock (
page 118).


Set the date in trip computer
(page 186).


Calibrate the compass
(page 188).


Resynchronize the ESP
(page 246).


Resynchronize side power windows
(page 146).


Resynchronize sliding / pop-up
roof*(
page 149).

288 Practical hintsFusesAuxiliary fuse box in front passenger footwell
The auxiliary fuse box is located in the
front passenger compartment.
1Lock
2CoverRemoving / installing cover

Turn both locks1 90
° counterclock-
wise.

Remove cover2 in direction of arrow.

Install cover2 in reverse order.