1995 TOYOTA SUPRA warning lights

DIAGNOSIS SYSTEM
The Electronically Controlled Transmission has built±in self±
diagnostic functions. If a malfunction occurs in the system,
the ECM stores the diagnostic trouble code in memory and
the O/D OFF (Overdrive OFF) indicator light blinks to inform
the driver. The diagnostic trouble code stored in memory can
be read out by the following procedure.
O/D OFF INDICATOR LIGHT INSPECTION
1. Turn the ignition switch ON.
2. Check if the O/D OFF indicator light lights up when the O/D
main switch is pushed out to OFF and goes off when the O/D
main switch is pushed in to ON.
HINT: If the O/D OFF indicator light does not light up or stay
on all the time, carry out the check for ºO/D OFF Indicator
Light Circuitº on page AT1±88.
DIAGNOSTIC TROUBLE CODE CHECK
1. Turn the ignition switch ON, but do not start the engine.
2. Push in the O/D main switch to ON.
HINT: Warning and diagnostic trouble codes can be read only
when the O/D main switch is ON. If it is OFF, the O/D OFF indi-
cator light up will light continuously and will not blink.
3. Using SST, connect terminals TE1 and E1 of the DLC 1 or
DLC2.
SST 09843±18020
4. Read the diagnostic trouble code indicated by the number of
times the O/D OFF indicator light blinks.
HINT: If the system is operating normally, the light will blink
2 times per second. AT1±34
± AT340E (2JZ±GE) AUTOMATIC TRANSMISSIONTROUBLESHOOTING

DIAGNOSIS SYSTEM
The automatic transmission has built±in self±diagnostic
functions. If a malfunction occurs in the system, the ECM
stores the diagnostic trouble code in memory and the O/D
OFF (Overdrive OFF) indicator light blinks to inform the driv-
er. The diagnostic trouble code stored in memory can be read
out by the following procedure.
O/D OFF INDICATOR LIGHT INSPECTION
1. Turn the ignition switch ON.
2. Check if the O/D OFF indicator light lights up when the O/D
main switch is pushed out to OFF and goes off when the O/D
main switch is pushed in to ON.
HINT: If the O/D OFF indicator light does not light up or stay
on all the time, carry out the check for ºO/D OFF Indicator
Light Circuitº on page AT2±108.
DIAGNOSTIC TROUBLE CODE CHECK
1. Turn the ignition switch ON, but do not start the engine.
2. Push in the O/D main switch to ON.
HINT: Warning and diagnostic trouble codes can be read only
when the O/D main switch is ON. If it is OFF, the O/D OFF indi-
cator light up will light continuously and will not blink.
3. Using SST, connect terminals TE1 and E1 of the DLC 1 or
DLC2.
SST 09843±18020
4. Read the diagnostic trouble code indicated by the number of
times the O/D OFF indicator light blinks
(See next page).
HINT: If the system is operating normally, the light will blink
2 times per second. AT2±34
± A340E (2JZÐGTE) AUTOMATIC TRANSMISSIONTROUBLESHOOTING

HAZARD WARNING SWITCH
INSPECTION
INSPECT SWITCH CONTINUITY
 
 Condition
 
 Tester connection to
terminal number
 
 Specified condition
 Switch OFF 7±10 Continuity 
 Switch ON
 
 7±8
4±5±6±9
 
 Continuity
 
 Illumination circuit
 
 2±3
 
 Continuity
If continuity is not as specified, replace the switch.
TURN SIGNAL FLASHER INSPECTION
INSPECT FLASHER OPERATION
(a) Connect the terminal 2 to battery positive (+) terminal and the
terminal 3 to battery negative (±) terminal.
(b) Connect the 2 turn signal light bulbs parallel to each other to
terminals 1 and 3, check that the bulbs flash.
HINT: The turn signal lights should flash between 60 and 120
times per minute. BE±22
± BODY ELECTRICAL SYSTEMTURN SIGNAL AND HAZARD WARNING SYSTEM

WARNING LIGHTS
 Trouble Parts name (See page)
 
 
 
 
 
Warning lights do not light up
(Except Discharge and Door Open)
 
 
 
 
 
1. Bulb
2. IGN Fuse (BE±6)
3. Ignition Switch (BE±8)
4. Meter Circuit Plate (BE±44)
5. Wire Harness
6. Generator
 
 
 
 
 
 
Brake Warning Light does not light up
 
 
 
 
 
 
1. Bulb
2. Brake Fluid Level Warning Switch (BE±52)
3. Parking Brake Switch (BE±52)
4. Bulb Check Relay
5. Meter Circuit Plate (BE±44)
6. Wire Harness
 
 
 
 
 
Seat Belt Warning Light does not light up
 
 
 
 
 
1. Bulb
2. Seat Belt Buckle Switch (BE±56)
3. Integration Relay (BE±55)
4. Meter Circuit Plate (BE±44)
5. Wire Harness
 
 
 
 
Engine Oil Level Warning Light does not light up
 
 
 
 
1. Bulb
2. Engine Oil Level Switch (BE±51)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
Low Oil Pressure Warning Light does not light up
 
 
 
1. Bulb
2. Low Oil Pressure Warning Switch (BE±51)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
 
 
 
 
Door Open Warning Light does not light up
 
 
 
 
 
 
 
1. Bulb
2. DOME Fuse (BE±5)
3. Door Courtesy Switch (BE±54)
4. Luggage Room Light Switch (BE±28)
5. Integration Relay
6. Meter Circuit Plate (BE±44)
7. Wire Harness
 
 
 
 
Master Warning Light does not light up
 
 
 
 
1. Bulb
2. Telltale Light (BE±48)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
BE±42± BODY ELECTRICAL SYSTEMCOMBINATION METER

INDICATOR LIGHTS
TroubleParts name (See page) 
 
 SRS Indicator Light does not light up
 
 
 
1. Bulb
2. Wire Harness
3. Center Air Bag Sensor (RS Section)
 
 
 
ABS Indicator Light does not light up
 
 
 
1. Bulb
2. Wire Harness
3. Traction ECU (BR Section)
 
 
 
Malfunction Indicator Light does not light up
 
 
 
1. Bulb
2. ECM (EG Section)
3. Wire Harness
 
 
 
TRAC OFF Indicator Light does not light up
 
 
 
1. Bulb
2. Traction Solenoid Relay (BR Section)
3. Traction ECU (BR Section)
4. Wire Harness
 
 
 
Security Indicator Light does not light up
 
 
 
1. Light Emitting Diode
2. Theft Deterrent and Door Lock ECU (BE±123)
3. Wire Harness
 
 
 
 
A/T Shift Position Indicator Light does not light up
 
 
 
 
1. Bulb
2. Park/Neutral Position Switch (AT1 Section)
3. Light Control Rheostat (BE±54)
4. Meter Circuit Plate (BE±44)
5. Wire Harness
 
 
 
 
MANU Indicator Light does not light up
 
 
 
 
1. Bulb
2. ECM (EG Section)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
 
O/D OFF Indicator Light does not light up
 
 
 
 
1. Bulb
2. O/D Main Switch
3. ECM (EG Section)
4. Meter Circuit Plate (BE±44)
5. Wire Harness
 
 
 
 
TRAC Indicator Light does not light up
 
 
 
 
1. Bulb
2. ABS and Traction ECU
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
Turn Indicator Light does not light up
 
 
 
1. Bulb
2. Turn Signal and Hazard Warning System (BE±20)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
 
High Beam Indicator Light does not light up
 
 
 
 
1. Bulb
2. Headlight System (BE±10)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
 
 
 
CRUISE Indicator Light does not light up
 
 
 
1. Bulb
2. Cruise Control ECU (BE±170)
3. Meter Circuit Plate (BE±44)
4. Wire Harness
± BODY ELECTRICAL SYSTEMCOMBINATION METERBE±43

2. INSECT RECEIVER GAUGE RESISTANCE
Measure the resistance between terminals.
 Between terminals Resistance (
)
 A±B Approx. 269.7
 A±C Approx. 123.5
 B±C Approx. 146.2
If resistance value is not as specified, replace the fuel receiv-
er gauge.
3. INSPECT SENDER GAUGE RESISTANCE
Measure the resistance between terminals 2 and 3 for each
float position.
 
 Float position mm (in.)
 
 Resistance (
)
 F Approx. 33.8 (1.33) Approx. 4.0
 1/2 Approx. 44.8 (1.76) Approx. 55.0
 E Approx. 141.1 (5.55) Approx. 107.0
If resistance value is not as specified, replace the sender
gauge.
FUEL LEVEL WARNING INSPECTION
1. INSPECT WARNING LIGHT
(a) Disconnect the connector from the sender gauge.
(b) Connect terminals 1 and 3 on the wire harness side
connector.
(c) Turn the ignition switch ON, check that the warning light lights
up.
If the warning light does not light up, test the bulb or inspect
wire harness.
2. INSPECT SWITCH
(a) Apply battery positive voltage between terminals 1 and 3
through a 3.4 W test bulb, check that the bulb lights up.
HINT: It will take a short time for the bulb to light up.
(b) Submerge the switch in fuel, check that the bulb goes out.
If operation is not as specified, replace the sender gauge.
± BODY ELECTRICAL SYSTEMCOMBINATION METERBE±49

LOW OIL PRESSURE WARNING
INSPECTION
1. INSPECT SWITCH
(a) Check that there is continuity between terminal and ground
with the engine stopped.
(b) Check that there is no continuity between terminal and
ground with the engine running.
HINT: Oil pressure should be over 29 kPa (0.3 kgf/ cm
2, 4.3
psi)
If operation is not as specified, replace the switch.
2. INSPECT WARNING LIGHT
(a) Disconnect the connector from the warning switch and
ground terminal on the wire harness side connector.
(b) Turn the ignition switch ON, check that the warning light lights
up.
If the warning light does not light up, test the bulb or inspect
wire harness.
ENGINE OIL LEVEL WARNING
INSPECTION
1. INSPECT SWITCH
(a) Check that there is continuity between terminal with the
switch in each position.
(b) Heat the switch to above 60°C (140°F) in an oil bath.
(c) Check that there is continuity between terminals with the
switch ON (float up).
(d) Check that there is no continuity between terminals with the
switch OFF (float down).
If operation is not as specified, replace the switch.
2. INSPECT WARNING LIGHT
(a) Disconnect the connector from the switch.
(b) Ground terminal 1 on the wire harness connector.
(c) Turn the ignition switch ON. Check that the warning light
lights up approximately 40 seconds later.
If the warning light does not light up, inspect bulb or wire har-
ness.
± BODY ELECTRICAL SYSTEMCOMBINATION METERBE±51

BRAKE FLUID LEVEL WARNING
INSPECTION
1. INSPECT SWITCH
(a) Remove the reservoir tank cap and strainer.
(b) Disconnect the connector.
(c) Check that there is no continuity between terminals with the
switch OFF (float up).
(d) Use syphon, etc. to take fluid out of the reservoir tank.
(e) Check that there is continuity between terminals with the
switch ON (float down).
(f) Pour the fluid back in the reservoir tank.
If operation is not as specified, replace the switch.
2. INSPECT WARNING LIGHT
(a) Disconnect the connector from the brake fluid warning
switch.
(b) Release the parking brake pedal.
(c) Connect terminals on the wire harness side of the level
warning switch connector.
(d) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or wire har-
ness.
PARKING BRAKE WARNING
INSPECTION
1. INSPECT SWITCH
(a) Check that there is continuity between terminal and switch
body with the switch ON (switch pin released).
(b) Check that there is no continuity between terminal and switch
body with the switch OFF (switch pin pushed in).
If operation is not as specified, replace the switch or inspect
ground point.
2. INSPECT WARNING LIGHT
(a) Disconnect the connector from the parking brake switch and
the brake fluid warning switch.
(b) Ground terminal on the wire harness side connector.
(c) Start the engine, check that the warning light lights up.
If the warning light does not light up, test the bulb or inspect
wire harness. BE±52
± BODY ELECTRICAL SYSTEMCOMBINATION METER