1995 TOYOTA SUPRA recommended oil

Simple Method:
(a) Quickly race the engine 5 times to 4,000 rpm.
(b) Remove the spark plug.
(c) Visually check the spark plug.
If the electrode is dry...OK
If the electrode is wet...Proceed to step 4
(d) Reinstall the spark plug.
3. REMOVE SPARK PLUGS
Using a 16 mm plug wrench, remove the 6 spark plugs.
4. VISUALLY INSPECT SPARK PLUGS
Check the spark plug for thread damage and insulator dam-
age.
If abnormal, replace the spark plug.
Recommended spark plug:
ND
PK16R11
NGK
BKR5EP11
5. INSPECT ELECTRODE GAP
Maximum electrode gap for used spark plug:
1.3 mm (0.051 in.)
If the gap is greater than maximum, replace the spark plug.
Correct electrode gap for new spark plug:
1.1 mm (0.043 in.)
NOTICE: If adjusting the gap of a new spark plug, bend only
the base of the ground electrode. Do not touch the tip. Never
attempt to adjust the gap on the used plug.
6. CLEAN SPARK PLUGS
If the electrode has traces of wet carbon, allow it to dry and
then clean with a spark plug cleaner.
Air pressure:
Below 588 kPa (6 kgfVcm
2, 85 psi)
Duration:
20 seconds or less
HINT: If there are traces of oil, remove it with gasoline before
using the spark plug cleaner.
7. REINSTALL SPARK PLUGS
Torque: 18 NVm (180 kgfVcm, 13 ftVlbf)
8. RECONNECT HIGH±TENSION CORDS TO SPARK
PLUGS IG±6
± IGNITION SYSTEM(2JZ±GE)

SERVICE SPECIFICATIONS
SERVICE DATA
 Firing order ± 1 ± 5 ± 3 ± 6 ± 2 ± 4 
 High±tension
cord 
 Resistance Limit 
 25 k
per cord
 
 
 
 
Spark plug 
 
 
 
Recommended spark plug ND
NGK
Correct electrode gap for new plug
Maximum electrode gap for used plug 
 
 
 
PK16R11
BKR5EP11
1.1 mm (0.043 in.)
1.3 mm (0.051 in.)
 
 
 
 
Ignition coil 
 
 
 
Primary coil resistance at cold
at hot
Secondary coil resistance at cold
at hot 
 
 
 
0.36±0.55

0.45±0.65

9.0±15.4 k

11.4±18.1 k

 
 
 
 
 
 
Distributor 
 
 
 
 
 
Air gap
Pickup coil resistance at cold G1±G

G2±G

NE±G

at hot G1±G

G2±G

NE±G
 
 
 
 
 
 
0.2±0.5 mm (0.008±0.020 in.)
125±200

125±200

155±250

160±235

160±235

190±290

TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf
 Spark plug x Cylinder head 18 180 13
IG±18± IGNITION SYSTEM2JZ±GE

SPARK PLUGS INSPECTION
NOTICE:
wNever use a wire brush for cleaning.
wNever attempt to adjust the electrode gap on used a spark
plug.
wSpark plugs should be replaced every 100,000 km (60,000
miles).
1. REMOVE IGNITION COILS ASSEMBLIES
(See ignition coils removal)
2. INSPECT ELECTRODE
Using a megger (insulation resistance meter), measure the
insulation resistance.
Standard correct insulation resistance:
10 M
or more
If the resistance is less than specified, proceed to step 4.
HINT: If a megger is not available, the following simple meth-
od of inspection provides fairly accurate results.
Simple Method:
(a) Quickly race the engine 5 times to 4,000 rpm.
(b) Remove the spark plug.
(c) Visually check the spark plug.
If the electrode is dry...OK
If the electrode is wet...Proceed to step 4
(d) Reinstall the spark plug.
3. REMOVE SPARK PLUGS
4. VISUALLY INSPECT SPARK PLUGS
Check the spark plug for thread damage and insulator dam-
age.
If abnormal, replace the spark plug.
Recommended spark plug:
ND
PK20R11
NGK
BKR6EP11
5. INSPECT ELECTRODE GAP
Maximum electrode gap for used spark plug:
1.3 mm (0.051 in.)
Correct electrode gap for new spark plug:
1.1 mm (0.043 in.)
NOTICE: If adjusting the gap of a new spark plug, bend only
the base of the ground electrode. Do not touch the tip. Never
attempt to adjust the gap on the used plug.
IG±22± IGNITION SYSTEM(2JZ±GTE)

SERVICE SPECIFICATIONS
SERVICE DATA
 Firing order ± 1 ± 5 ± 3 ± 6 ± 2 ± 4 
 
 
 
Spark plug 
 
 
 
Recommended spark plug ND
NGK
Correct electrode gap for new plug
Maximum electrode gap for used plug 
 
 
 
PK20R11
BKR6EP11
1.1 mm (0.043 in.)
1.3 mm (0.051 in.)
 
 
Ignition coil 
 
Primary coil resistance at cold
at hot 
 
0.54±0.84

0.68±0.98

 
 
 
 
Camshaft
position
sensor 
 
 
 
Resistance at cold

at hot 
 
 
 
835±1,400
for NIPPONDENSO
985±1,600
for AISAN
1,060±1,645
for NIPPONDENSO
1,265±1,890
for AISAN
 
 
 
 
Crankshaft
position
sensor 
 
 
 
Resistance at cold
at hot 
 
 
 
835±1,400
for NIPPONDENSO
985±1,600
for AISAN
1,060±1,645
for NIPPONDENSO
1,265±1,890
for AISAN
TORQUE SPECIFICATIONS
 Part tightened NVm kgfVcm ftVlbf Ignition coil bracket x Cylinder head 8.8 90 78 in.Vlbf 
 Ignition coil x Ignition coil bracket 
 2.5 
 35 
 3.4 in.Vlbf
 Camshaft position sensor x Cylinder head 8.8 90 78 in.Vlbf
 Engine hanger x Cylinder head 39 400 29
 Crankshaft position sensor x Oil pump 8.8 90 78 in.Vlbf
± IGNITION SYSTEM2JZ±GTEIG±31

LUBRICATION SYSTEM
PREPARATION
SST (SPECIAL SERVICE TOOLS)
09032±00100 Oil Pan Seal Cutter
09228±07500 Oil Filter Wrench
09316±60010 Transmission & Transfer Bearing
Replacer
(09316±00010) Replacer Pipe
09816±30010 Oil Pressure Switch Socket
No.2 oil pan
Crankshaft front oil seal
RECOMMENDED TOOLS
09040±00010 Hexagon Wrench Set
09040±00020 Torx Socket E10
09200±00010Engine Adjust Kit
A/C compressor stud bolt
EQUIPMENT
 
 Oil pressure gauge 
 
 
 Precision straight edge 
  Oil pump
 
 Torque wrench 
 
± ENGINELUBRICATION SYSTEMEG±359

LUBRICANT
 Item Capacity Classification
 
 
 
 
 
Engine oil (2JZ±GE)
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change 
 
 
 
 
6.5 liters (6.9 US qts, 5.7 Imp. qts)
5.3 liters (5.6 US qts, 4.7 Imp. qts)
4.9 liters (5.2 US qts, 4.3 Imp. qts)
 
 
 
 
 
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multigrade
engine oil and recommended viscosity oil,
with SAE 5W±30 being preferred engine oil
 
 
 
 
Engine oil (2JZ±GTE)
Dry fill
Drain and refill
w/ Oil filter change
w/o Oil filter change 
 
 
 
6.5 liters (6.9 US qts, 5.7 Imp. qts)
5.0 liters (5.3 US qts, 4.4 Imp. qts)
4.7 liters (5.0 US qts, 4.1 Imp. qts)
 
 
 
 
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multigrade
engine oil and recommended viscosity oil
SSM (SPECIAL SERVICE MATERIALS)
 
 
 
 
08826±00080 Seal Packing Black or equivalent
(FIPG) 
 
 
 
Oil pump
No.1 oil pan
No.2 oil pan
 
 
 
08833±00080 Adhesive 1344,
THREE BOND 1344,
LOCTITE 242 or equivalent 
 
 
Oil pressure switch
Idler pulley pivot bolt
EG±360± ENGINELUBRICATION SYSTEM

PREPARATION
RECOMMENDED TOOLS
09200±00010 Engine Adjust Kit.
EQUIPMENT
 Dial indicator Brake disc
 Micrometer Brake disc
 Mirror Brake hose
 Thermometer 
 Torque wrench 
 Vernier calipers Parking brake drum
COOLANT
 Item Capacity Classification 
 Engine coolant 2JZ±GE M/T
(w/ Heater) A/T7.3 liters (7.7 US qts, 6.4 lmp. qts)
8.3 liters (8.8 US qts, 7.3 lmp. qts)Ethylene±glycol base
 
 
()
2JZ±GTE M/T
A/T
(q q)
9.5 liters (10.0 US qts, 8.4 lmp. qts)
9.4 liters (9.9 US qts, 8.3 lmp. qts)
LUBRICANT
 Item Capacity Classification
 
 
Engine oil (Drain and refill) (2JZ±GE)
w/ Oil filter change
w/o Oil filter change
5.3 liters (5.6 US qts, 4.7 lmp. qts)
4 9 liters (5 2 US qts 4 3 lmpqts)
API grade SH, Energy±Conserving II
multigrade engine oil or ILSAC multi-
grade engine oil and recommended 
 
w/o Oil filter change4.9 liters (5.2 US qts, 4.3 lmp. qts)grade engine oil and recommended
viscosity oil, with SAE 5W±30 being
preferred engine oil
 
 Engine oil (Drain and refill) (2JZ±GTE)
w/ Oil filter change
5.0 liters (5.3 US qts, 4.4 lmp. qts)
API grade SH, Energy±Conserving II
mutigrade engine oil or ILSAC multi-
 
 
g
w/o Oil filter change
(q q)
4.7 liters (5.0 US qts, 4.1 lmp. qts)
gg
grade engine oil and recommended
viscosity oil
 Manual transmission oil 2JZ±GE2.6 liters (2.7 US qts, 2.3 lmp. qts)API GL±5 SAE 75W±90
  2JZ±GTE
(q, q)
1.8 liters (1.9 US qts, 1.6 lmp. qts)Castle gear oil V160
 Automatic transmission 2JZ±GE1.6 liters (1.7 US qts, 1.4 lmp. qts)ATF DEXRON® II
 fluid (Drain and refill) 2JZ±GTE
(q, q)
1.9 liters (2.0 US qts, 1.7 lmp. qts)ATF TYPE T±II
 
 
Differential oil1.35 liters (1.43 US qts, 1.19 lmp. qts)API GL±5
Above±185 C (05 F)
SAE 90 
 
 
SAE 90
Below±185 C (05 F)
SAE 80W±90 or 80W
± MAINTENANCEPREPARATIONMA±5

Recommended spark plug:
2JZ±GE
ND
PK16R11
HGK
BKR5EP11
2JZ±GTE
ND
PK20R11
NGK
BKR6EP11
NOTICE: If adjusting the gap of a new spark plug, bend
only the base of the ground electrode. Do not touch the
tip.
(g) Using a 16 mm plug wrench, reinstall the 6 spark plugs.
Torque: 18 NVm (180 kgfVcm, 13 ftVlbf)
(h) Reconnect the high±tension cords.
(i) 2JZ±GE:
Reinstall the cylinder head rear cover.
(j) Reinstall the No.3 timing belt cover.
(k) 2JZ±GE:
Reinstall the throttle body.
(See throttle body installation in SFI System)
6. REPLACE ENGINE OIL AND OIL FILTER
(See oil and filter replacement in Lubrication System)
2JZ±GE:
Oil grade:
API grade SH Energy±Conserving II multigrade engine
oil or ILSAC multigrade engine oil. Recommended
viscosity is as follows with SAE 5W±30 being the
preferred engine oil for your vehicle.
Drain and refill capacity:
w/ Oil filter change
5.3 liters (5.6 US qts, 4.7 lmp. qts)
w/o Oil filter change
4.9 liters (5.2 US qts, 4.3 lmp. qts)
± MAINTENANCEMAINTENANCE OPERATIONSMA±7