1995 TOYOTA SUPRA recommended oil

2JZ±GTE:
Oil grade:
API grade SH Energy±Conserving II multigrade engine
oil or ILSAC multigrade engine oil. Recommended
viscosity is given in the following chart.
Drain and refill capacity:
w/ Oil filter change
5.0 liters (5.3 US qts, 4.4 lmp. qts)
w/o Oil filter change
4.7 liters (5.0 US qts, 4.1 lmp. qts)
7. REPLACE ENGINE COOLANT
(See coolant replacement in Cooling System)
Capacity (w/ Heater):
2JZ±GE
M/T
7.3 liters (7.7 US qts, 6.4 lmp. qts)
A/T
8.3 liters (8.8 US qts, 7.3 lmp. qts)
2JZ±GTE
M/T
9.5 liters (10.0 US qts, 8.4 lmp. qts)
A/T
9.4 liters (9.9 US qts, 8.3 lmp. qts)
HINT:
wUse a good brand of ethylene±glycol base coolant and
mix it according to the manufacturer's directions.
wUsing coolant which includes more than 50%
ethylene±glycol (but not more than 70%) is
recommended.
NOTICE:
wDo not use a alcohol type coolant.
wThe coolant should be mixed with demineralized water or
distilled water.
8. INSPECT CHARCOAL CANISTER
(a) Remove the charcoal canister.
(b) Visually inspect the canister case.
(c) Check for crogged each port and stuck check valve.
wUsing low compressed air (4.71 kPa (48 gf/cm2, 0.68
psi)), blow into port C and check that air flows without
resistance from the other ports. MA±8
± MAINTENANCEMAINTENANCE OPERATIONS

09031±00030
09042±00020
09905±00012
Pin Punch

Torx Socket T40

Snap Ring No.1 Expand

RECOMMENDED TOOLS
EQUIPMENT
 


Calipers 
 
  Dial indicator
 
Dial indicator
  Micrometer
 
Micrometer
  Torque wrench
 
Torque wrench
  Feeler gauge

Feeler gauge
LUBRICANT
 Item Capacity Classification
 
Manual transmission oil2 6 liters (2 7 US qts 2 3 Imp qts) API GL±3, GL±4 or GL±5
  Manual transmission oil 2.6 liters (2.7 US qts, 2.3 Imp. qts) API GL 3, GL 4 or GL 5
SAE 75W±90
SSM (SPECIAL SERVICE MATERIALS)
 
 
 
 
08826±00090 Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG) 
 
 
 
Transmission case x
Intermediate plate
Front bearing retainer x
Transmission case
 
 
08833±00080 Adhesive 1344,
THREE BOND 1344, Straight screw plug
Front bearing retainer bolt
 

,
LOCTITE 242 or equivalent
g
± W58 MANUAL TRANSMISSIONPREPARATIONMT1±5

PREPARATION
SST (SPECIAL SERVICE TOOLS)
09325±20010 Transmission Oil Plug2JZ±GE M/T
09330±00021Companion Flange Holding Tool
09330±50010 Propeller Shaft Center Bearing
Replacer
09370±50010 Drive Line Angle Gauge
2JZ±GE
09325±40010 Transmission Oil Plug2JZ±GE A/T
09608±12010 Front Hub & Drive Pinion Bearing
Replacer Set
(09608±00070) Drive Pinion Rear Bearing Cone
ReplacerCenter support bearing
Center support bearing(09608±06040)Front Hub Inner Bearing Cone
Replacer
09608±35014 Axle Hub & Drive Pinion Bearing
Tool Set
09922±10010 Variable Open WrenchAdjusting nut
09950±00020Bearing Remover
09905±00012Snap Ring No. 1 Expander

RECOMMENDED TOOLS
PR±2± PROPELLER SHAFTPREPARATION

FRONT SUSPENSION
PREPARATION
SST (SPECIAL SERVICE TOOLS)
 
 
 
 
 
 
09628±62011 Ball Joint Puller 
 
 
 
 
 
 
 
 
 
 
09710±14012 Rear Suspension Bushing Tool Set 
 
 
 
Shock absorber bushing
replacement
 
 
 
 
 
 
 
 
(09710±00020) Pipe 
 
 
 
 
 
 
 
 
 
09727±30020 Coil Spring Compressor 
 
 
RECOMMENDED TOOLS
 
 
 
 
 
 
 
 
09025±00010 Torque Wrench (30 kgfVcm) 
 
 
 
EQUIPMENT
 
 Torque wrench 
 
Corrected 6/20/01 ± MH
SA±20± SUSPENSION AND AXLEFRONT SUSPENSION

RECOMMENDED TOOLS
09924±12361 Deep socket Wrench 36.
09025±00010 Torque Wrench (30 kgf
cm)
09031±00030 Pin Punch.
(2JZ±GTE M/T)
Drive pinion nut removal
and installation
Differential preload
(Conventional differential only)
Pinion shaft removal
EQUIPMENT
 
 
Dial indicator with magnetic base 
 
 
 
Micrometer 
 
 
 
Torque wrench 
 
 
 
Vernier calipers 
 
SSM (SPECIAL SERVICE MATERIALS)
 
 
 
 
08826±00090 Seal Packing 1281,
THREE BOND 1281 or equivalent
(FIPG) 
 
 
 
Differential carrier X Cover
 
 
 
 
08833±00100 THREE BOND 1360K or equivalent 
 
 
 
Differential case X Ring gear
LUBRICANT
 
 Item
 
 Capacity
 
 Classification
 
 
 
 
Differential oil
 
 
 
 
1.35 liters (1.43 US qts, 1.19 lmp.qts)
 
 
 
 
API GL±5 Hypoid gear oil
[Above ± 18°C (0°F)]
SAE 90
[Below ± 18°C (0°F)]
SAE 80W or 80W±90
SA±56± SUSPENSION AND AXLEREAR DIFFERENTIAL

(See page EG±20)
Check idle speed.
Proceed to matrix chart of problem symp-
toms on page EG±514.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Switch OFF all accessories.
(4) Switch OFF air conditioning.
(5) Connect tachometer test probe to terminal
IG of data link connector 1.
Check Idle speed.
Idle speed: 650  50 rpm

Never allow tachometer test probe to touch
ground as it could result in damage to igniter
and/or ignition coil.

As some tachometers are not compatible
with this ignition system, we recommended
that you confirm the compatibility of your
unit before use.
Check ignition timing.
(1) Shift transmission into ªNº position.
(2) Warm up engine to normal operating tempera±
ture.
(3) Keep the engine speed at idle.
(4) Using SST, connect terminals TE1 and E1 of
data link connector 1.
SST 09843±18020
(5) Connect a timing light clip to the check wire.
(See page EG±20)
Check ignition timing.
Ignition timing: 10 2° BTDC @ idle
Proceed to matrix chart of problem symp-
toms on page EG±514.
Proceed to page EG±518 and continue to
troubleshoot.
± ENGINE2JZ±GTE ENGINE TROUBLESHOOTINGEG±507