1995 SUBARU LEGACY light

E: TCS OFF INDICATOR LIGHT DOES NOT
GO OFF.
—ABS WARNING, TCS WARNING AND TCS
OPERATING INDICATOR LIGHTS COME ON
AND GO OFF PROPERLY WHEN STARTING
THE ENGINE, BUT TCS OFF INDICATOR
DOES NOT GO OFF FOR MORE THAN 30
SECONDS AFTER ENGINE RUNNING.—
Does malfunction indicator lamp (Check engine
lamp) come on?
No
Ye s
Conduct OBD II diagnosis.

1. Check harness connector between ABS/TCS
control module and TCS OFF indicator light.
OK
Not OK
Repair harness/connector.
Replace ABS/TCS control module.
B4M0396


26
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

B4M0718A
1. CHECK HARNESS CONNECTOR BETWEEN ABS/
TCS CONTROL MODULE AND TCS OFF INDICATOR
LIGHT.
1) Turn ignition switch OFF.
2) Disconnect all connectors from ABS/TCS control mod-
ule.
3) Turn ignition switch ON.
4) Measure voltage between ABS/TCS control module
connector and body.
Connector & terminal / Specified voltage:
(P6) No. 10—body / 10—13 V
27
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

F: TCS OPERATING INDICATOR LIGHT DOES
NOT GO OFF.
—WHEN STARTING THE ENGINE, ABS
WARNING, TCS WARNING AND TCS OFF
INDICATOR LIGHTS COME ON AND GO OFF
PROPERLY BUT TCS OPERATING
INDICATOR LIGHT ONLY KEEPS ON.—
1. Check harness connector between ABS/TCS
control module and TCS operating indicator
light.
OK
Not OK
Repair harness/connector.
Replace ABS/TCS control module.
B4M0398

28
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

B4M0719A
1. CHECK HARNESS CONNECTOR BETWEEN ABS/
TCS CONTROL MODULE AND TCS OPERATING
INDICATOR LIGHT.
1) Turn ignition switch OFF.
2) Disconnect all connectors from ABS/TCS control mod-
ule.
3) Turn ignition switch ON.
4) Measure voltage between ABS/TCS control module
connector and body.
Connector & terminal / Specified voltage:
(P6) No. 11—body / 10—13 V
29
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

G: TCS OFF SWITCH DOES NOT FUNCTION.
—TCS OFF INDICATOR LIGHT COMES ON
AND GOES OFF PROPERLY WHEN
STARTING THE ENGINE, WHILE THIS LIGHT
NEITHER COMES ON NOR GOES OFF WHEN
PUSHING THE TCS OFF SWITCH.—
1. Check TCS OFF switch
OK
Not OK
Replace TCS OFF switch.
2. Check harness connector between ABS/TCS
control module and TCS OFF switch.
OK
Not OK
Repair harness/connector.
Replace ABS/TCS control module.
B4M0535


30
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

B4M0720A
1. CHECK TCS OFF SWITCH.
1) Turn ignition switch OFF.
2) Disconnect connector from TCS OFF switch.
3) Measure resistance between TCS OFF switch termi-
nals.
Connector & terminal / Specified resistance:
(i9) No. 5—No.3/1Ωor less
(When the switch is pressed,
turns ON.)
/1MΩor less
(When the switch is released,
turns OFF.)
B4M0401A
2. CHECK HARNESS CONNECTOR BETWEEN ABS/
TCS CONTROL MODULE AND TCS OFF SWITCH.
1) Turn ignition switch OFF.
2) Disconnect connector to TCS OFF switch.
3) Disconnect connector from ABS/TCS control module.
4) Measure resistance between ABS/TCS control module
connector terminals.
Connector & terminal / Specified resistance:
(P7) No. 16—body / 1Ωor less (When the switch
is pressed, turns ON.)
/1MΩor more (When the
switch is released, turns OFF.)
31
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

H: ABS WARNING, TCS WARNING, TCS
OPERATING INDICATOR AND/OR TCS OFF
INDICATOR LIGHTS DO NOT COME ON.
—TROUBLE IN WARNING LIGHT DRIVE
CIRCUIT—
DIAGNOSIS:

Faulty ABS warning light

Faulty TCS warning light

Faulty TCS OFF light

Faulty TCS operating indicator light

Faulty harness connector

Faulty ABS/TCS control module
TROUBLE SYMPTOM:

Warning light does not illuminate.

Impossible to read trouble code.
Check warning light bulb.
OK
Not OK
Repair warning light bulb.
1. Check warning light power supply.
OK
Not OK
Repair ABS warning light power line.
2. Check input voltage of ABS/TCS control mod-
ule.
OK
Not OK
Repair harness/connector.
3. Check ground line of ABS/TCS control mod-
ule.
OK
Not OK
Repair ground line.
Replace ABS/TCS control module.




32
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure

B4M0402
B4M0403A
1. CHECK WARNING LIGHT POWER SUPPLY.
1) Turn ignition switch OFF.
2) Disconnect combination meter.
3) Turn ignition switch ON.
4) Measure voltage between combination meter connector
and body.
Connector & terminal / Specified voltage:
(i14) No. 11—body / 10—13 V
33
4-4bBRAKES
7. Diagnostics Chart for Warning Light Circuit Failure