1995 NISSAN ALMERA N15 engine oil

Ohmmeter- + WARNING
LAMPSANDBUZZER
Oil Pressure SwitchCheck
Oil pressure
Continuity
kPa (bar, kg/cm
2,
psi)
More than10-20
NO
Engine
start
(0.10-0.20, 0.1-0.2, 1.4-2.8)
Less than10-20
YES
Engine
stop
(0.10-0.20, 0.1-0.2, 1.4-2.8)
SEL748K
Test lamp 3.4WON

\ ,I

"
/

Ballery
Test lamp 3.4W OFF

~0
CD

Ballery
Gasoline MEL623D
SEL901F
Check
thecontinuity betweentheterminals ofoil pressure
switch andbody ground.

Fuel Warning LampSensor Check

• Itwill take ashort timeforthe bulb tolight.

Diode Check

• Check continuity usinganohmmeter.
• Diode isfunctioning properlyiftest results areasshown in
the figure atleft.

NOTE:

Specification mayvary depending onthe type oftester. Before
performing thisinspection, besure torefer tothe instruction
manual forthe tester tobe used.

• Diodes forwarning lampsarebuilt intothecombination
meter printed circuit.

Refer to"Combination Meter"(EL-127).
Warning BuzzerUnit

• Seat beltwarning lampiscontrolled bythe warning buzzer
unit.

Refer to"Warning Buzzer"(EL-152).
EL-151
•

PRECAUTIONSANDPREPARATION
Precautions
• When installing rubberparts,finaltightening mustbecar-
ried outunder unladen condition* withtires onground.
*: Fuel, radiator coolantandengine oilfull. Spare tire,
jack,

hand tools andmats indesignated positions.
• After installing removedsuspension parts,check wheel
alignment andadjust ifnecessary.
• Use flare nutwrench whenremoving orinstalling brake
tubes.
• Always torquebrakelineswhen installing.

Tool number
Tool name
SBR820B
Special Service Tools

Description

HT72520000

Ball joint remover Removing
tie-rodouterendandlower ball
joint

NT146
HT71780000

Spring compressor

ST35652000
Strut attachment
NT144
Removing
andinstalling coilspring
Fixing strutassembly

NT145
GG94310000

Flare nuttorque wrench

KV38106700
KV381 06800

Differential sideoilseal
protector
NT406
NT147
FA-2
Removing
andinstalling brakepiping

a:
10mm (0.39 in)

Installing driveshaft

LH: KV38106700
RH: KV38106800

FRONTSUSPENSION SYSTEM
SEC. 391-400-401

When installing rubberparts,finaltightening mustbecarried outunder unladen condition" withtires onground .
• Fuel, radiator coolantandengine oilfull. Spare tire,jack, hand tools andmats indesignated positions.

~~25.29
~ (2.5•3.0, 18•22)

\ \
...

5

~ 98•118 (10•12, 72•87)

Front

to.J:
N. m (kg-m, ft-Ib)

SFA715B

CD
Suspension member

@
Stabilizer bar

@
Drive shaft
@

Coilspring

@
Strut assembly

@
Knuckle

FA-4
(J)

Transverse link

@
Front struttower bar

ON-VEHICLESERVICE
Front Wheel Alignment

Before checking frontwheel alignment, besure tomake apre-
liminary inspection (Unladen*).
*: Fuel, radiator coolantandengine oilfull. Spare tire,jack,
hand tools andmats indesignated positions.

SFA575B PRELIMINARY INSPECTION

1. Check tiresforwear andimproper inflation.
2. Check wheelrunout.

Wheel runout:
Refer toSOS (FA-30).

3. Check frontwheel bearings forlooseness.
4. Check frontsuspension forlooseness.
5. Check steering linkageforlooseness.
6. Check thatstruts workproperly.
7. Check vehicle posture (Unladen).

TOE-IN Measure toe-inusingfollowing procedure.
WARNING:
• Perform following procedure alwaysonaflat surface.
• Make surethatnoperson isin front ofthe vehicle before
pushing it.

1. Bounce frontofvehicle upand down tostabilize theposture.
2. Push thevehicle straight aheadabout5m (16 ft).
3. Put amark onbase lineoftread (rearside) ofboth tires at
the same height ashub center. Thesearemeasuring points.
4. Measure distance"A"(rear side).
5. Push thevehicle slowlyaheadtorotate thewheels 180
degrees (1/2turn).

If the wheels haverotated morethan180degrees
(112
turn), try
the above procedure againfromthebeginning. Neverpush
vehicle backward.

6. Measure distance"B"(front side).

Total toe-in
Refer toSOS (FA-29).
CAMBER,
CASTERANDKINGPIN INCLINATION
Camber, casterandkingpin inclination arepreset atfactory and
cannot beadjusted.

1. Measure camber,casterandkingpin inclination ofboth right
and leftwheels withasuitable alignment gauge.

Camber, CasterandKingpin inclination:
Refer toSOS (FA-29).

2. Ifcamber, casterorkingpin inclination isnot within
specification, inspectfrontsuspension parts.Replace dam-
aged orworn outparts.

Front
SFA948A
SFA614B
SFA234AC
Lines
parallel to
center lineofbody

Q

Front

Hub
center
height
FA-6

SEC.391.400.401

When installing rubberparts,finaltightening
must becarried outunder unladen condition'
with tires onground.
• Fuel, radiator coolanta'1dengine 011full.
Spare tire,Jack, hand toolsandmats In
designated positions.

@
~

L.~
(3.2-4.3, 23•31)

Front

CD
Spacer

@
Strut mounting insulator

@
Strut mounting insulator
bracket

@
Thrust bearing

@
Upper spring seat

@
Upper spring rubber seat

(J)
Bumper rubber

@
Coilspring
FRONT
SUSPENSION
@
Lower spring rubber seat

@)
Strut assembly

@
Suspension member

@
Stabilizer bar

@
Stabilizer clamp

@
Connecting rod

@
Transverse link

@
Compression rodclamp

@
Drive shaft

FA-24
~~
59.74
~~~.~ ::'.4:9- 54)

o
(2.5_3.0,
18 -22)
~
~~
~ ~

9=:

~~
-----J

/~18-24

1/ ~
(1.8.2.4,13.17)
~. @

&1
(@

~ J~!~5

(20-28, 145 •203)
~ 59•74 (6.0 -7.5, 43•54)

SFA624B

@
Knuckle

@
Cotter pin

@)
ABS sensor

@
Plain washer

@
Wheel bearing locknut

@
Insulator

@
Adjusting cap

@
Cotter pin

SERVICEDATAANDSPECIFICATIONS (50S)
General Specifications

Suspension type
Strut type
Stabilizer Independent
macpherson struts
Double-acting hydraulic
For 14-and 15-inch wheelmodels

Inspection andAdjustment
WHEEL ALIGNMENT (Unladen*1)

GAengine andSR CDengine andSR
Applied model engine
models with enginemodels with
14-inch wheels 15-inchwheels
Camber Minimum

-no'

(-1.33')

.

Degree minute Nominal
-0'35'
(-0.58')
(Decimal degree)Maximum 0'10'
(0.1
r)

Caster Minimum

0'40'(0.6r)

Degree minute Nominal
1
'25' (1.42')
(Decimal degree)Maximum 2'10'
(217")
Kingpin inclination Minimum14'00'
(14.00')
Degree minute Nominal
14'45'
(14.75')
(Decimal degree)Maximum 15'30'
(15.50')
Total toe-in Minimum0(0)
Distance (A-B) Nominal
2(008)
mm (in) Maximum 4(0.16)
Minimum 0'
(0.00')
Angle (leftplus right)
Nominal 11'
(0.18')
Degree minute
(Decimal degree)Maximum 22'
(0.37")
Wheel turning angle Minimum
38'00'
(38.00') 34'00'(34.00')
Inside Nominal4nO'
(41.00')
3rOO'(37.00')

Degree minute
(Decimal degree)Maximum
42'00'
(42.00')
38'00'(38.00')
Full (urn'2
Outside
Degreeminute Nominal 34'00'
(34.00') 31'00'(3100')
(Decimal degree)
'1' Fuel, radiator coolantandengine oilfull. Spare tire,jack, hand tools andmats indesignated positions.
'2: On power steering models,wheelturning force(atcircumference ofsteering wheel)of98 to147 N(10 to15 kg, 22to33 Ib)with engine
idle

FA-29
•