1995 NISSAN ALMERA N15 engine oil

BODYEND
Body Front End

• When removing orinstalling hood,placeacloth orother padding onhood. Thisprevents vehiclebody
from being scratched.
• Bumper fasciaismade ofplastic. Donot use excessive forceandbesure tokeep oilaway fromit.
• Hood adjustment: Adjustathinge portion.
• Hood lockadjustment: Afteradjusting, checkhoodlockcontrol operation. Applyacoat ofgrease to
hood locks engaging mechanism.
• Hood opener: Donot attempt tobend cable forcibly. Doingsoincreases effortrequired tounlock
hood.

REMOVAL -Front bumper assembly

CD
Remove frontairspolier. Referto"Front
air
spoiler" in"EXTERIOR" fordetails, BT-33.

@
Remove boltssecuring bumperfasciatoengine undercover.

CID
Remove clips
@QD
securing frontgrille.

@
Remove screwssecuring leftand right turnsignal lampsandremove thelamps.

@
Remove screwsandclips
@W
*1,
@
*2
securing
leftand right sides offront fender protector.

@)
Remove boltssecuring leftand right front fenders tobumper fascia.
([) Remove boltsandclips
@W
securing retainertobumper fascia.

@)
Extract bumper fasciaassembly.

*1: Standard bumpertype
*2: Aero bumper type

to.J:
N'm (kg-m, ft-Ib)

SBT037
B1-5
•

CHECKANDADJUSTMENT

OK
MINMax.
line
Min. line
SBR418C
Checking
BrakeFluidLevel

• Check fluidlevel inreservoir tank.Itshould bebetween
Max. andMin. lines onreservoir tank.
• Iffluid level isextremely low,check brakesystem forleaks.
• Ifbrake warning lampcomes on,check brakefluidlevel
switch andparking brakeswitch.

ABR159
SBR419C
Checking
BrakeLine

CAUTION: If leakage occursaround joints,retighten or,ifnecessary,
replace damaged parts.
1. Check brakelines(tubes andhoses) forcracks, deteriora-
tion orother damage. Replaceanydamaged parts.
2. Check foroilleakage byfully depressing brakepedalwhile
engine isrunning.

Changing BrakeFluid

CAUTION:
• Refill withnewbrake fluid"DOT 3"or"DOT 4".
• Always keepfluidlevel higher thanminimum lineonreser-
voir tank.
• Never reusedrained brakefluid.
• Donot mix different typesofbrake fluids(DOT3,DOT 4).
• Becareful nottosplash brakefluidonpainted areas;itmay •
cause paintdamage. Ifbrake fluidissplashed onpainted :•
areas, washitaway withwater immediately.
1. Clean inside ofreservoir tank,andrefill withnewbrake
fluid.
2. Connect avinyl tubetoeach airbleeder valve.
3. Drain brake fluidfrom each airbleeder valvebydepressing
brake pedal.
4. Refill untilnewbrake fluidcomes outofeach airbleeder
valve.
Use same procedure asinbleeding hydraulic systemto
refill brake fluid.
Refer to"Bleeding Procedure", BR-6.

BR-5

GROUNDDISTRIBUTION
GROUND CONNECTTO CONN.
NO. CELLCORD
E37/E51 AIRBAG DIAGNOSIS SENSORUNIT(Single
E108 RS-SRS
air bag system)
BRAKE FLUIDLEVEL SWITCH E2EL-WARN
CLEARANCE LAMPLH E50EL-TAILIL
CLEARANCE LAMPRH E33EL-TAILIL
COOLING FANMOTOR-1 (1-modetype) E45 EC-COOLIFHA-A/C
COOLING FANMOTOR-1 (2-modetype-GA
E66 EC-COOLIF
HA-A/C
engine forEurope)
COOLING FANMOTOR-1 (2-modetype-ex-
E46 EC-COOLIF
HA-A/C
eept GAengine forEurope)
COOLING FANMOTOR-2 (1-modetype)
E39 EC-COOLIFHA-A/C

-

COOLING FANMOTOR-2 (2-modetype-GA
E67 EC-COOLiF
HA-A/C
engine forEurope)
COOLING FANMOTOR-2 (2-modetype-ex-
E40 EC-COOLIFHA-A/C
eept GAengine forEurope)
COOLING FANRELAY-1 E12
EC-COOLIFHA-A/C
COOLING FANRELAY-2 E17
EC-COOLIFHA-A/C
COOLING FANRELAY-3 E18EC-COOLIF
HA-A/C
DAYTIME LIGHTUNIT E119EL-DTRL
FRONT FOGLAMP LH E52EL-F/FOG
FRONT FOGLAMP RH
E36EL-F/FOG
FRONT TURNSIGNAL LAMPLH E53EC-TURN
FRONT TURNSIGNAL LAMPRH E32EC-TURN
FRONT WIPERANDWASHER SWITCH E113
EL-WIPER
FUEL FILTER SWITCH
E5EL-WARN
HEADLAMP AIMINGMOTOR UNITLH E48
EL-AIM
HEADLAMP AIMINGMOTOR UNITRH E35 EL-AIM
HEADLAMP LH E49EL-H/LAMP
EL-DTRL
HEADLAMP RH E34EL-H/LAMP
EL-DTRL
HEADLAMP WIPERMOTOR LH E44
EL-HLC
HEADLAMP WIPERMOTOR RH E41EL-HLC
IACV-FICD SOLENOID VALVE(LHDmodels
.

E65 EC-A/CCUTHA-A/C
with CD20 engine)
INHIBITOR SWITCH E222EC-PNP/SWAT-A
IT EL-START
NEUTRAL POSITION SWITCH E220EC-PNP/SW
POWER STEERING OILPRESSURE SWITCH
E3 EC-PST/SW
(RHO models withgasoline engine)
REAR FOGLAMP RELAY E20EL-R/FOG
REAR WIPER ANDWASHER SWITCH E112EL-WIP/R
REAR WIPER RELAY E15EL-WIP/R
SIDE TURN SIGNAL LAMP(Driver side) E1 EL-TURN
WASHER FLUIDLEVEL SWITCH E30EL-WARN
EL-20

GROUNDDISTRIBUTION
GROUND CONNECT
TO CONN.NO.
CELLCORD

M28/M68
POWERSTEERING OILPRESSURE SWITCH
(LHD models) (LHDmodels withoutA8S,dualairbag and M82 EC-PST/SW

M28/M60/M68
rearpower window)
(RHD models)
POWERWINDOW RELAY
M16EL-ILLEL-WINDOW
REAR FOGLAMP SWITCH M55EL-R/FOGEL-ILLEL-8UZZER
REAR WINDOW DEFOGGER SWITCH M53EL-ILLEL-DEF
REAR WINDOW DEFOGGER TIMER M37EL-DEF
REAR WIPER AMPLIFIER (RHDmodels) M21EL-WIP/R
RECIRCULATION SWITCH M46HA-A/C
SIDE TURN SIGNAL LAMP(Passenger side)
(GA engine without A8S,dualairbag and M81 EL-TURN
rear power window)
SUN ROOF RELAY M16EL-SROOF
WARNING 8UZZERUNIT(ForAustralia)
M38EL-8UZZER
FRONT WIPERMOTOR (WithA8S,dualair
8105 EL-WIPER
bag orrear power window)

-_._-
-

REAR WIPER AMPLIFIER (LHDmodelsl 88EL-WIP/R

0-

IACV-FICD SOLENOID VALVE(RHDmodels
8102 EC-A/CCUTHA-A/C
with CDengine)
POWER STEERING OILPRESSURE SWITCH
(LHD models withASS, dualairbag orrear 8102 EC-PST/SW
power window)
SIDE TURN SIGNAL LAMP(Passenger side)
(Except GAengine without A8S,dualairbag 8108 EL-TURN
and rear power window)
AIR 8AG DIAGNOSIS SENSORUNIT(Dual air
Z1 RS-SRS
bag system)
SPOT LAMP
R2EL-INT/L
DOOR LOCKACTUATOR (Driverside)
D8 EL-D/LOCK
DOOR LOCKACTUATOR (Passengerside)
D38 EL-D/LOCK
DOOR MIRROR DEFOGGER (Driverside)
D4 EL-DEF
DOOR MIRROR DEFOGGER (Passengerside)
D34 EL-DEF
LOCK KN08 SWITCH
D9EL-D/LOCK
POWER WINDOW MAINSWITCH (Without
D6 EL-WINDOW
rear power window)
POWER WINDOW MAINSWITCH (Withrear
D7 EL-WINDOW EL-D/LOCK
power window)
EL-22

GROUNDDISTRIBUTION
GROUND CONNECT
TO CONN.
NO. CELLCORD
F13/F14 DISTRIBUTOR
(CAMSHAFTPOSITIONSEN-
F24 EC-CMPS
SOR)
DISTRIBUTOR (POWERTRANSISTOR) F24EC-IGN/SG
ECM (ECCS CONTROL MODULE) F1EC-MAIN
IACV-FICD SOLENOID VALVE(GA16DE
F9EC-FICDHA-A/C
engine exceptforEurope andIsrael)
IACV-FICD SOLENOID VALVE(GAengine for
F11 EC-FICD
HA-A/C
Europe andIsrael andGA15DE engine)
SHIELD WIRE(CAMSHAFT POSITIONSEN-
F24 EC-CMPS
SOR)
SHIELD WIRE(HEATED OXYGENSENSOR) F23
EC-H02S
SHIELD WIRE(KNOCK SENSOR) (GAengine) F102
EC-KS
SHIELD WIRE(MASS AIRFLOW SENSOR)
(GA engine forEurope andIsrael and F12 EC-MAFS
GA15DE engine)
SHIELD WIRE(MASS AIRFLOW SENSOR)
(GA 16DE engine exceptforEurope andIsrael F27
EC-MAFS
and SRengine)
SHIELD WIRE(OXYGEN SENSOR) F22
EC-02S
SHIELD WIRE(THROTTLE POSITIONSEN-
F8 EC-TPS
SOR)
IACV-AIR REGULATOR E214
EC-AIRREG
IACV-FICD SOLENOID VALVE(SRengine) E212 EC-FICD
HA-A/C
SHIELD WIRE(KNOCK SENSOR) (SRengine) E215 EC-KS
E205 ALTERNATOR E233
EL-CHARGE EL-WARN
B11/B32 FRONT
DOORSWITCH (Driverside) B9RS-SRSEL-BUZZER
(Sedan) FUELPUMP B17
EC-F/PUMP
B11/B32/D105
(Hatchback) FUEL
TANK GAUGE UNIT B18EL-METEREL-WARN
HEATED SEATLH B12EL-H/SEAT
HEATED SEATRH B16EL-H/SEAT
HEATED SEATSWITCH LH B13
EL-H/SEAT
HEATED SEATSWITCH RH B15
EL-H/SEAT
REAR COMBINATION LAMPLH(TAIL AND
B27 EL-TAILILEL-STOP/L
STOP) (Hatchback)
REAR COMBINATION LAMPLH(TURN SIG-
B27 EL-TURN
NAL) (Hatchback)
REAR COMBINATION LAMPRH(TAIL AND
B28 EL-TAILIL
EL-STOP/L
STOP) (Hatchback)
REAR COMBINATION LAMPRH(TURN SIG-
B28 EL-TURN
NAL) (Hatchback)
HIGH-MOUNTED STOPLAMP (Inrear air
D112 EL-STOP/L
spoiler) (Hatchback)
HIGH-MOUNTED STOPLAMP (Onrear win-
D108 EL-STOP/L
dow) (Hatchback)
LICENSE PLATELAMPLH(Hatchback)
D107EL-TAILIL
LICENSE PLATELAMPRH(Hatchback)
D109EL-TAILIL
EL-23
•

CHARGINGSYSTEM
Service DataandSpecifications (SOS)

ALTERNATOR

A5T06891LR170-746E LR170-504B A2T82491A
Type MITSUBISHIHITACHIMITSUBISHI
Applied model GA
engines CD20SR20DE
Nominal rating V-A
12-70 12-80
Ground polarity Negative
Minimum revolutions
under no-load Less
than
Lessthan1,000 Less
than
(when 13.5Visapplied) 1,300 1,300
rpm
Hot output current More
than Morethan
(When 13.5Visapplied) More
than 22/1,300 27/1,300
Morethan

.
21/1,300
Morethan More
than 22/1,300
More than 50/2,500 56/2,500More
than
50/2,500 Morethan Morethan 65/2,500
A/rpm 67/5,000
66/5,000
Regulated output
14.1-14.7
voltage V
Minimum lengthof
50(0.197) 6.0
(0.236) 5.0(0.197)
brush mm(in)
Brush spring pressure 4.609
-5.786 1.0-343 0.92
-328 4.609-5.786
(470 -590, (102
-350, (94-334, (470
-590,
N (g, oz)
16.58 -20.81) 3.60
-12.34) 332-11.78) 16.58
-20.81)
Slip ringminimum
221(0.870) 26.0
(1.024) 31.6(1.244) 221(0.870)
diameter mm(in)
Rotor coilresistance at
2.5-2.9 258 4824
-29
20'C (68'F)

n

EL-61
•

Bulbcover
SEL995K HEADLAMP
Bulb Replacement

The headlamp isasemi-sealed beamtypewhich usesa
replaceable halogenbulb.Thebulb canbereplaced fromthe
engine compartment sidewithout removing theheadlamp body.

• Grasp onlytheplastic basewhen handling thebulb. Never
touch theglass envelope.

1. Disconnect thebattery cable.
2. Disconnect theharness connector fromtheback sideofthe
bulb.
3. Turn thebulb retaining ringcounterclockwise until
it
is free
from theheadlamp reflector,andthen remove it.
4. Pull offthe rubber cap.
5. Remove theheadlamp bulbcarefully. Donot shake orrotate
the bulb when removing it.
6. Install inthe reverse orderofremoval.

CAUTION:
• Do not leave headlamp reflector withoutbulbforalong
period oftime. Dust,moisture, smoke,etc.entering head-
lamp bodymayaffect theperformance ofthe head lamp.
Remove headlamp bulbfrom thehead lamp reflector just
before areplacement bulbisinstalled.
Bulb Specifications

Item
Semi-sealed beam
High/Low Wattage
(W)

60/55

f>
to

3 21 0

~ nOD

o
SEL226PAiming
Adjustment

When performing headlamp aiming adjustment, useanaiming
machine, aimingwallscreen orheadlamp tester.Aimers
should beingood repair, calibrated andoperated inaccor-
dance withrespective operationmanuals.
If any aimer isnot available, aimingadjustment canbedone as
follows:

For details, refertothe regulations inyour owncountry.
CAUTION:
• Keep alltires inflated tocorrect pressures.
• Place vehicle andtester onone and same flatsurface.
• See thatvehicle isunloaded (exceptforfull levels of
coolant, engineoiland fuel, andspare tire,jack andtools).
Have thedriver orequivalent weightplaced indriver's seat.
CAUTION: •
Be sure aiming switchisset to
"0"
when performing aiming
adjustment onvehicles equipped withheadlamp aiming con-
trol.
EL-75

GEL001EXTERIOR
LAMP
Front FogLamp BulbReplacement

The front foglamp isasemi-sealed beamtypewhich usesa
replaceable halogenbulb.

• Grasp onlytheplastic basewhen handling thebulb. Never
touch theglass envelope.

1. Disconnect thebattery cable.
2. Disconnect theharness connector fromtheback sideofthe
bulb.
3. Turn thebulb retaining ringcounterclockwise untilitis free
from thefront foglamp reflector, andthen remove it.
4. Pull offthe rubber cap.
5. Remove thefront foglamp bulbcarefully. Donot shake or
rotate thebulb when removing it.
6. Install inthe reverse orderofremoval.

CAUTION:
.' Donot leave frontfoglamp reflector withoutbulbforalong
period oftime. Dust, moisture, smoke,etc.entering frontfog
lamp bodymayaffect theperformance ofthe front foglamp.
Remove frontfoglamp bulbfrom thefront foglamp reflec-
tor just before areplacement bulbisinstalled.
Front FogLamp Aiming Adjustment

Before performing aimingadjustment, makesureofthe follow-
ing.
a. Keep alltires inflated tocorrect pressure.
b. Place vehicle onlevel ground.
c. See thatvehicle isunloaded (exceptforfull levels of
coolant, engineoiland fuel, andspare tire,jack, andtools).
Have thedriver orequivalent weightplaced indriver's seat.
Adjust aiming byturning theadjusting screw.

EL-101
•