1995 NISSAN ALMERA N15 instrument panel

PREPARATIONANDPRECAUTIONS
Service Notice
Supplemental RestraintSystem(SRS)"AIR
BAG" (DualAirBag System)

The Supplemental RestraintSystem"AirBag" usedalong withaseat belt, helps toreduce therisk or
severity ofinjury tothe driver andfront passenger inafrontal collision. TheSupplemental Restraint
System consists ofair bag modules (locatedinthe center ofthe steering wheelandonthe instrument
panel onthe passenger side),adiagnosis sensorunit,warning lamp,wiring harness andspiral cable.
Information necessarytoservice thesystem safelyisincluded inthe
RSsection
ofthis Service Manual.

WARNING:
• Toavoid rendering theSRS inoperative, whichcouldincrease therisk ofpersonal injuryordeath
in the event ofacollision whichwould resultinair bag inflation, allmaintenance mustbeperformed
by an authorized NISSANdealer.
• Improper maintenance, includingincorrectremovalandinstallation ofthe SRS, canlead topersonal
injury caused byunintentional activationofthe system.

Ii
Donot use electrical testequipment onany circuit related tothe SRS unless instructed tointhis
Service Manual. SRSwiring harnesses arecovered withyellow insulation eitherjustbefore the
harness connectors orfor the complete harness,foreasy identification.

•
Before proceeding withdisassembly, thor-
oughly cleantheoutside ofthe transaxle. Itis
important toprevent theinternal partsfrom
becoming contaminated bydirt orother for-
eign matter.
• Disassembly shouldbedone inaclean work
area.
• Use lint-free clothortowels forwiping parts
clean. Common shopragscanleave fibers
that could interfere withtheoperation ofthe
transaxle.
• Place disassembled partsinorder, onaparts
rack, foreasier andproper assembly.
• Allparts should becarefully cleaned-witha
general purpose, non-flammable solvent
before inspection orreassembly.
• Gaskets, sealsandO-rings shouldbe
replaced anytime thetransaxle isdisassem-
bled.
• Itis very important toperform functional tests
whenever theyareindicated. •
The valve bodycontains precision partsand
requires extremecarewhen partsare
removed andserviced. Placedisassembled
valve bodyparts inorder, onaparts rack,for
easier andproper assembly. Carewillalso
prevent springs andsmall partsfrombecom-
ing scattered orlost.
• Properly installedvales,sleeves, plugs,etc.
will slide along theirbores inthe valve body
under theirownweight.
• Before assembly, applyacoat ofrecom-
mended ATFtoall parts. Apply petroleum
jelly toprotect O-ringandseals, orhold bear-
ings andwashers inplace during assembly.
Do not use grease.
• Extremely careshould betaken toavoid dam-
age toO-rings, sealsandgaskets when
assembling.
• After overhaul, refillthetransaxle withnew
ATF.

•

Supplemental RestraintSystem(SRS)"AIR
BAG" (Single AirBag System)

The Supplemental RestraintSystem"AirBag" andused along withaseat belt,helps toreduce therisk
or severity ofinjury tothe driver inafrontal collision. TheSupplemental RestraintSystemconsists of
an air bag module (located inthe center ofthe steering wheel),adiagnosis sensorunit,warning lamp,
wiring harness andspiral cable. Information necessarytoservice thesystem safelyisincluded inthe

RS section
ofthis Service Manual.

WARNING:
• Toavoid rendering theSRS inoperative, whichcouldincrease therisk ofpersonal injuryordeath
in the event ofacollision whichwould resultinair bag inflation, allmaintenance mustbeperformed
by an authorized NISSANdealer.
• Improper maintenance, includingincorrectremovalandinstallation ofthe SRS, canlead topersonal
injury caused byunintentional activationofthe system.
• Donot use electrical testequipment onany circuit related tothe SRS unless instructed tointhis
Service Manual.
AT-7

______ HANDLINGPRECAUTIONS FORPLASTICS __
BODYALIGNMENT _
Location OfPlastic Parts
Underbody

Kicking plate(PP)
Front

@,
076
dia.
Rear
@,@
62 dia.

Front
Rear
coordinates: coordinates:
@,@ @,@@
X :250
X:393.5
X:475
V :-632
V:1,460
V:3,082
Z :224.8
Z:126.9
Z:336.8
@,@
(8),
@
@
X :492 X
:572
X:-542
V :-450 V
:1,940
V:3,082
Z :355 Z
:200
Z:336.8
@,@
CD,
CD

X :406
X:600
V :64
V:2,035
Z :172
Z:235.2
@,@
Q)

X :352.7 X
:150
V :69 V
:2,442.9
Z :240 Z
:241

@,
@
@
X :432
X:300
V :338
V:2,480
Z :128
Z:381.8
(f),
CD
@
X :395
X:-300
V :515
V:2,480
Z :129.2
Z:405.8

@,
@)

X :393
Y :2,560
Z :365
@
X :470
Y :2,911
Z :339.6
@
X :-539
Y :2,911
Z :339.6
Unit: mm
Coordinates:
@,0
X :522.2
V :18.1
Z :571.7
@,@ X :465
V :2,456.4
Z :522

Front
andrear strut tower centers

I

~t-~

Rear
(f
••@
LH side
RHside

Q
Q

Bottom
view of

,1

vehicle

__
MEASURMENT POINTS__

Glove box(PPC)
Side
wind molding(PVC)
Cluster lidC(PPC)
Instrument
panel(PPC)
Console box(PPC)

5-door
Hatchback

Cluster lidA(PPC)

~----_/

Front
pillargarnish(PPC)
Side
wind molding(PVC)
Back doorfinisher(ABS)
Roof
spoilar(FRP)

3-doorHatchback

Center pillarlower garnish(PP)
Center pillarupper garnish(PPC)
Rear pillar garnish(PPC)
High
mounted stoplamp
(Lens: PMMA )
Housing: ABS

FrontSBT097

-27-
-18-

______ HANDLINGPRECAUTIONS FORPLASTICS __
BODYALIGNMENT _
Location OfPlastic Parts
Underbody

Kicking plate(PP)
Front

@,
076
dia.
Rear
@,@
62 dia.

Front
Rear
coordinates: coordinates:
@,@ @,@@
X :250
X:393.5
X:475
V :-632
V:1,460
V:3,082
Z :224.8
Z:126.9
Z:336.8
@,@
(8),
@
@
X :492 X
:572
X:-542
V :-450 V
:1,940
V:3,082
Z :355 Z
:200
Z:336.8
@,@
CD,
CD

X :406
X:600
V :64
V:2,035
Z :172
Z:235.2
@,@
Q)

X :352.7 X
:150
V :69 V
:2,442.9
Z :240 Z
:241

@,
@
@
X :432
X:300
V :338
V:2,480
Z :128
Z:381.8
(f),
CD
@
X :395
X:-300
V :515
V:2,480
Z :129.2
Z:405.8

@,
@)

X :393
Y :2,560
Z :365
@
X :470
Y :2,911
Z :339.6
@
X :-539
Y :2,911
Z :339.6
Unit: mm
Coordinates:
@,0
X :522.2
V :18.1
Z :571.7
@,@ X :465
V :2,456.4
Z :522

Front
andrear strut tower centers

I

~t-~

Rear
(f
••@
LH side
RHside

Q
Q

Bottom
view of

,1

vehicle

__
MEASURMENT POINTS__

Glove box(PPC)
Side
wind molding(PVC)
Cluster lidC(PPC)
Instrument
panel(PPC)
Console box(PPC)

5-door
Hatchback

Cluster lidA(PPC)

~----_/

Front
pillargarnish(PPC)
Side
wind molding(PVC)
Back doorfinisher(ABS)
Roof
spoilar(FRP)

3-doorHatchback

Center pillarlower garnish(PP)
Center pillarupper garnish(PPC)
Rear pillar garnish(PPC)
High
mounted stoplamp
(Lens: PMMA )
Housing: ABS

FrontSBT097

-27-
-18-

BODY
&
TRIM
SECTION
BT
CONTENTS
* For seat belt,refer toMA and RSsection.
* For wiring diagrams ofbody electrical systems,refertoEL section.
PRECAUTIONS
2
Service Notice 2
Supplemental RestraintSystem(SRS)"AIR
BAG" (DualAirBag System) 2
Supplemental RestraintSystem(SRS)"AIR
BAG" (Single AirBag System) 2
GENERAL SERViCiNG 3
Clip andFastener
3

BODY END
5

Body Front End
5

Body RearEndandOpener 7
DOOR 11
Front Door 11
Rear Door
12

INSTRUMENT PANEL
13

INTERIOR TRIM 16
Side andFloor Trim
16

Door Trim 22Roof
Trim 24
Trunk RoomTrim 26
Back DoorTrim 27
EXTERIOR 28
SEAT 35
Front Seat
35

Heated Seal... 36
Rear Seat 37
SUNROOF 39
WINDSHIELD ANDWINDOWS 43
Windshield andRear Window 43
Back DoorWindow 44
Rear SideWindow
.45

MIRROR 46
Door Mirror .46
BODY ALIGNMENT 47
Engine Compartment 47
Underbody .49

•

PRECAUTIONS
Service Notice

• When removing orinstalling variousparts,placeacloth orpadding ontothevehicle bodytoprevent
scratches.
• Handle trim,molding, instruments, grille,etc.carefully duringremoving orinstalling. Becareful not
to soil ordamage them.
• Apply sealing compound wherenecessary wheninstalling parts.
• When applying sealingcompound, becareful thatthesealing compound doesnotprotrude from
parts.
• When replacing anymetal parts(forexample bodyouter panel, members, etc.),besure totake rust
prevention measures.

SupplementalRestraintSystem(SRS)"AIR
BAG" (DualAirBag System)

The Supplemental RestraintSystem"AirBag", usedalong withaseat belt,helps toreduce therisk or
severity ofinjury tothe driver andfront passenger inafrontal collision. TheSupplemental Restraint
System consists ofair bag modules (locatedinthe center ofthe steering wheelandonthe instrument
panel onthe passenger side),adiagnosis sensorunit,warning lamp,wiring harness andspiral cable.
Information necessarytoservice thesystem safelyisincluded inthe
RSsection
ofthis Service Manual.

WARNING:
• Toavoid rendering theSRS inoperative, whichcouldincrease therisk ofpersonal injuryordeath
in the event ofacollision whichwould resultinair bag inflation, allmaintenance mustbeperformed
by an authorized NISSANdealer.
• Improper maintenance, includingincorrectremovalandinstallation ofthe SRS, canlead topersonal
injury caused byunintentional activationofthe system.
• Donot use electrical testequipment onany circuit related tothe SRS unless instructed tointhis
Service Manual. SRSwiring harnesses arecovered withyellow insulation eitherjustbefore the
harness connectors orfor the complete harness,foreasy identification.
Supplemental RestraintSystem(SRS)"AIR
BAG" (Single AirBag System)

The Supplemental RestraintSystem"AirBag", usedalong withaseat belt,helps toreduce therisk or
severity ofinjury tothe driver inafrontal collision. TheSupplemental RestraintSystemconsists ofan
air bag module (located inthe center ofthe steering wheel),adiagnosis sensorunit,warning lamp,
wiring harness andspiral cable. Information necessarytoservice thesystem safelyisincluded inthe

RS section
ofthis Service Manual.

WARNING:
• Toavoid rendering theSRS inoperative, whichcouldincrease therisk ofpersonal injuryordeath
in the event ofacollision whichwould resultinair bag inflation, allmaintenance mustbeperformed
by an authorized NISSANdealer.
• Improper maintenance, includingincorrectremovalandinstallation ofthe SRS, canlead topersonal
injury caused byunintentional activationofthe system.
• Donot use electrical testequipment onany circuit related tothe SRS unless instructed tointhis
Service Manual.
BT-2

INSTRUMENTPANEL
CAUTION:
• Disconnect bothbattery cablesinadvance.
• Disconnect airbag system lineinadvance.
• Never tamper withorforce airbag lidopen, asthis may adversely affectairbag performance.
• Becareful nottoscratch padandother parts.
REMOVAL -Instrument panelassembly

Instrument panelassembly
Remove airbag module (driver's) andsteering wheel.
Refer to"SUPPLEMENTAL RESTRAINTSYSTEM"inRS section fordetails.

CD
Steering columncoverandcombination switch
• Remove screws.

l6l
Instrument lowerpanel ondriver side
• Remove screws.

@
Cluster lidC
• Remove screwsanddisconnect harnessconnectors. Audio

&AIC
control
Consolebox

@
Cluster lidA
• Remove screws.

@
Combination meter
• Remove screwsanddisconnect harnessconnectors.

cID
Audio and
AIC
control unit
• Remove screwsfromtheinstrument panel.

(J)
Glove boxassembly
• Remove gloveboxpin.
• Then disconnect passengerairbag module
connector.

@
Passenger airbag module
• Refer to"SUPPLEMENTAL RESTRAINT
SYSTEM" inRS section fordetails.
@
AIT
finisher orMIT shift lever boot

@
Rear console box
• Remove consolemaskandscrews.

@
Front console box
• Remove screwsandbolts.

@
Instrument mask
• Disconnect harnessconnector.

@
Front pillargarnish
• Refer to"Side andFloor Trim" in"INTE-
RIOR TRIM" fordetails, 8T-16.

@
Instrument panelandpads
II

• Remove boltsandnuts.
• Remove doormirror switch anddisconnect
the connector.
•

8T-13

SEC.248-251-272-487-680-685-969

8INSTRUMENT
PANEL
Metalclip
rn

* :
Instrument panelassembly .
mounting
bolts
&
nuts.

SBT046

8T-14

Toinstrument panel
m

INTERIOR
TRIM
Side andFloor Trim(Cont'd)
8T-17 8BT049

•