2017 INFINITI QX30 Owner's Manual

GIVING VOICE COMMANDS
1. Push<>located on the steering wheel.
2. A list of commands appears on the screen, and the system provides a voice menu
prompt.
When this screen is displayed, almost all of
the commands can be recognized. Available
commands for each categories can be shown
on the right side of the screen. Highlight a
category listed in the left side of the screen
with the INFINITI controller to find your pre-
ferred command.
Selecting a category by touching the screen
or pushing <
/OK>will execute the com-
mand. After executing the category com-
mand, only the commands related to the
selected category can be recognized. Command list
in the5. Starting and driv-
ing section
3. After the tone sounds and the icon on the screen changes from
to, speak a
command. You can also select a command
by directly touching the screen.
The Voice Recognition system will pause
operation when the INFINITI controller is
moved. To resume operation, push <
>on
the steering wheel.
4. Continue to follow the voice menu prompts and speak after the tone sounds until the
preferred operation is completed.
To cancel the voice command, push and hold
<
>.
You can interrupt the voice prompt at any time
by pushing <
>.
Operating tips
•Speak a command after the tone.
•If the command is not accepted, the system
announces, “Please say again”. Repeat the
command in a clear voice.
•Push<>on the steering-wheel switch
once to return to the previous screen.
•Voice commands spoken from the passenger
seat cannot be recognized.
•When the <>on the steering wheel is
pressed while the air conditioner is set to the
Auto mode, the system controls the air con-
ditioner fan speed in order to improve voice
recognition performance. When the fan
speed is set higher than the 4th speed
position, the fan speed is decreased to 4th
speed. When the air conditioner is set to the
manual mode, the fan speed does not
change. The accuracy of voice recognition
may be affected depending on the fan speed
and the air direction.
•To skip the voice guidance function and give
the command immediately, push <>on
the steering-wheel to interrupt the system.
Remember to speak after the tone.
•To cancel the command, push and hold
<> or <>on the steering-wheel.
•Push <>on the steering-wheel to stop
the voice prompt and give the command at
once. Remember to wait for the tone before
speaking.
NAA1732
4-104Display screen, heater and air conditioner, and audio system

•To adjust the volume of the system feedback,
push the volume switch on the steering
wheel or use the audio system >
while the system is making an announce-
ment.
•For searching with Street Address, Point of
Interest and City Center, the searching area
is automatically set to the state where your
vehicle is located. Use Change State/
Province to change the search area to an-
other state if necessary.
How to see voice command screen
1. Push <>to display the first screen of the
voice command list.
2. Speak a command or select an item from the voice command list. The second screen is
displayed.
3. Speak a command. The list screen is dis- played.
4. Speak the preferred number from the list to perform operation.
The voice commands can be spoken one at a
time following prompts step by step or the
command can be spoken successively in one
step.
1Shows available command list. It is also
available to select a command from this
list by touching or using the INFINITI con-
troller.
2Shows available command list. Displayed
commands are only available to execute
through voice recognition. You can say
commands from the left screen and the
right screen continuously.
3Previously selected command.
4Command list:
You can say a command from the list,
touch the screen directly or select, using
steering switch or the INFINITI controller.
You can say preferred word for<>en-
closed part of the command.
5[Previous]/[Next]:
Say as a command or touch to go to the
previous/next screen. It cannot be se-
lected using the steering switch or
INFINITI controller.
5GD0015XZFirst screen5GD0016XZSecond screen
Display screen, heater and air conditioner, and audio system4-105

6Command numbers:
Speak 1 to 6 numbers to select. Also, you
can touch the screen directly, using the
steering switch or INFINITI controller.
How to speak numbers
Voice Recognition requires the user speak num-
bers in a certain way when giving voice com-
mands.
General rule
:
Only single digits 0 (zero) to 9 can be used. (For
example, if speaking 500, “five zero zero” can
be used, but “five hundred” cannot.)Examples
:
1-800-662-6200
“One eight zero zero six six two six two zero
zero”
For the best recognition, speak “zero” for the
number “0” and “oh” for the letter “o”.
Voice command examples
As examples, some additional basic operations
that can be performed by voice commands are
described here.
Example 1- Placing call from handsfree phone-
book
:
1. Push
<>located on the steering wheel.
2. Wait for the indicator to change to
and
speak “Phone”.
You can also speak “Phone” and then “Call
” successively.
3. Speak “Call ”. When options (Home, Work, etc.) are regis-
tered to a name in the contact list of a
cellular phone, the option can be com-
manded directly.
Example, “Call Steve Brown Work” or “Call
Steve Brown Other”
5GE0015XZList screen5GE0022XZ
4-106Display screen, heater and air conditioner, and audio system

4. The system prompts you to speak or selectan item number from the displayed list. To
select a displayed matching item speak a
number from between 1 and 6.
If the selected number has more than one
phone number registered to it, the phone
number list screen is displayed. Example 2 - Playing radio:
1. Push
<>located on the steering wheel.
2. Wait for the indicator to change to
and
speak “Audio”.
3. Speak “Play FM” to turn on the FM radio.
Display screen, heater and air conditioner, and audio system4-107

Command list
To use the Voice Recognition function, you can speak commands in the order of 1st command, 2nd command and 3rd command. You can also operate
the system with directly speaking the 2nd or 3rd command.
Variable numbers or words such as names can be applied in < > when speaking a command.
See the separate Navigation System Owner’s Manual (if equipped) for the navigation command.
General command
CommandAction
Show More Com-
mands Display other commands of the same category.
Go Back Correct the last recognition result to return to the previous screen.
Exit Cancel Voice Recognition.
Next Skip to next page.
Previous Skip to previous page.
General phone command
The following commands can be used during the phone Voice Recognition session.
Command Action
Dial The system makes a call to spoken phone number.
Change Number Correct the phone number when it is not recognized (available during phone number entry).
4-108Display screen, heater and air conditioner, and audio system

Phone command
1st command 2nd command 3rd command 4th command Action
Phone Call <1 - 6> Make a call to a contact that is stored on the cellular phone.Select from the list of displayed on the right side screen.
Call Make a call to a contact that is stored on the cellular phone. Make a call to a contact that is stored on the cellular phone. You can select type from
, , or .
Dial <#> Dial Make a call to a spoken phone number.
Change Number Change the number to call.
Dial Make a call to a spoken phone number.
Speak “3 columns or 4 columns (1–****)”
Make a call to a spoken phone number. Speak “7 columns or 10 columns or 11 columns or 3 columns” (“911” or “411” or “611”).
Recent Calls <1 - 6> Make a call to the recent incoming, outgoing or missed call number.
Read Text <1 - 6> Play Listen to recent text messages received. ReplyReply to received message.
Call Call the sender of the message.
Send Text Select a text message from the list and send it a contact name. You can select type
from , , or .

Phonebook Make a call to a contact that is stored on the cellular phone. You can select type from
“Work”, “Mobile”, “Home” or “Other”.
Select “Reply” to reply by message. Select “Call” to call the sender.

Display screen, heater and air conditioner, and audio system4-109

Phone command
1st command 2nd command 3rd command 4th command Action
Phone Favorites <1-6> Access frequently called contacts by storing into them in the favorite list.


Redial Make a call to the last outgoing phone number.
International Call Makes an international call by allowing more than 11 digits to be spoken.
You may need to include the international call prefixes and country codes.
Add Phone Use this command to connect a compatible Bluetooth® device to the system. Follow
the on screen instructions to complete the pairing process from your handset.
Call Work <1 - 6> To call someone’s work place, say the person’s name stored in the phonebook on your
cellular phone between “Call” and “Work”.
Call Cellular <1 - 6> To call someone’s cellular phone, say the person’s name stored in the phonebook on
your cellular phone between “Call” and “Mobile”.
Call Home <1 - 6> To call someone’s home, say the person’s name stored in the phonebook on your
cellular phone between “Call” and “Home”.
Call Other <1 - 6> To call someone at a place categorized as “Other”, say the person’s name stored in the
phonebook on your cellular phone between “Call” and “Other”.
NOTE
The system can read out SMS text messages in
voice. However, it cannot always read the text
correctly.
4-110Display screen, heater and air conditioner, and audio system

Audio command
1st com-
mand2nd command 3rd command Action
Audio AM Switches to the AM band, selecting the station last played. FM Switches to the FM band, selecting the station last played.
FM ,87.9–107.9. Switches to the FM band, selecting the station of the preferred frequency.
SXM ,channel #> Switches to the SiriusXM Satellite Radio band, selecting the preferred channel.
SXM Switches to the SiriusXM Satellite Radio band, selecting the channel last played.
USB Play Artist
<1 - 6> Turns on the USB mode, selecting the artist.
iPod Play Artist
<1 - 6> Turns on the iPod mode, selecting the artist.
USB Play Artist Turns on the USB mode, selecting the artist.
iPod Play Artist Turns on the iPod mode, selecting the artist.
USB Turns on the USB mode, selecting the last played mode.
iPod Turns on the iPod mode, selecting the last played mode.
USB Play Album
<1 - 6> Turns on the USB mode selecting the album.
iPod Play Album
<1 - 6> Turns on the iPod mode selecting the album.
USB Play Album Turns on the USB mode, selecting the album.
iPod Play Album Turns on the iPod mode, selecting the album.
AM <530–1710> Switches to the AM band, selecting the preferred station
FM <87.7–107.9> HD <#> Switches to the FM HD band, selecting the preferred station
CD Track <#> Turns on the CD, selecting the track number.
Display screen, heater and air conditioner, and audio system4-111