2017 INFINITI QX30 center console

Lumbar support:
The lumbar support feature provides lower back
support to the driver.
Push each side of the adjusting switch to adjust
the seat lumbar area until the desired position
is achieved.
1To raise the seatback contour
2To soften the seatback contour
3To lower the seatback contour
4To harden the seatback contour
SEAT HEATER (IF EQUIPPED)
The seats can be warmed by built-in heaters.
The switches are located on the center console
(for front seats) and can be operated indepen-
dently of each other. For more information on
the seat heater, seeSeat heating (if
equipped) in the2. Instruments and controls
section.
REAR SEATS
WARNING
•Never allow anyone to ride in the cargo area
or on the rear seat when it is in the fold-
down position. Use of these areas by pas-
sengers without proper restraints could re-
sult in serious injury or deathin an accident
or sudden stop.
•Properly secure all cargo with ropes or straps
to help prevent it from sliding or shifting. Do
not place cargo higher than the seatbacks. In
a sudden stop or collision, unsecured cargo
could cause personal injury.
•Do not allow people to ride in any area of
your vehicle that is not equipped with seats
and seat belts. Be sure everyone in your
vehicle is in a seat and using a seat belt
properly.
•Do not allow more than one person to use
the same seat belt.
•Do not fold down the rear seats when occu-
pants are in the rear seat area or any lug-
gage is on the rear seats. – Make sure that the seat path is clear
before moving the seat.
– Be careful not to allow hands or feet to
get caught or pinched in the seat.
•Head restraints/headrests should be ad-
justed properly as they may provide signifi-
cant protection against injury in an acci-
dent. Always replace and adjust them
properly if they have been removed for any
reason.
•If the head restraints/headrests are re-
moved for any reason, they should be se-
curely stored to prevent them from causing
injury to passengers or damage to the ve-
hicle in case of sudden braking or an acci-
dent.
•When returning the seatbacks to the up-
right position, be certain they are com-
pletely secured in the latched position. If
they are not completely secured, passen-
gers may be injured in an accident or sud-
den stop.
NIC2607
Safety — seats, seat belts and supplemental restraint system1-5

system checked. It is recommended you visit an
INFINITI retailer for these services.
If an abnormality occurs in the system, the VDC
system function will be canceled, but the ve-
hicle is still driveable. For additional informa-
tion, seeVehicle Dynamic Control (VDC)
system in the5. Starting and driving section.
WARNING
VDC should remain on unless freeing a vehicle
from mud or snow.
While the VDC system is operating, you might
feel a slight vibration or hear the system work-
ing when starting the vehicle or accelerating,
but this is normal.
Front fog light indicator light (if
equipped)
The light comes on when the front fog lights are
switched on (see Fog light switch (If so
equipped) later in this section).
High beam assist indicator light
(if equipped)
The indicator light illuminates when the head-
lights come on while the headlight switch is in
the AUTO position with the high beam selected.
This indicates that the high beam assist system
is operational. (See 2-63.)
High beam indicator light
This blue light comes on when the headlight
high beams are on and goes out when the low
beams are selected.
The high beam indicator light also comes on
when the passing signal is activated.
Rear fog light indicator light
The light comes on when the rear fog light is
switched on (see Fog light switch (If so
equipped) later in this section).
Side light and headlight
indicator light
This light comes on when the side light or
headlight position is selected, see Headlight
and turn signal switches later in this section
for further details.
/Front passenger air
bag status light
The front passenger air bag status light ()
located on the center console above the shift
lever will illuminate when the front passenger
air bag is turned OFF. When the front passenger
air bag is turned on, the front passenger air bag
status light ON (
) will illuminate.
For more details, see Front passenger air bag
and status light in the1. Safety — seats, seat
belts and supplemental restraint system sec-
tion.
AUDIBLE REMINDERS
Parking brake reminder chime
A chime will sound when driving away if the
parking brake has not been released. Stop the
vehicle and release the parking brake.
Light reminder chime
With the ignition switch placed in the OFF
position, a chime sounds when the driver’s door
is opened if the side lights are on. Turn the
headlight control switch off before leaving the
vehicle.
2-14Instruments and controls

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Disabled See Operator’s
Manual] The front-passenger front air bag is disabled during the journey although an adult or person of corresponding stature is on the front
passenger seat.
Front passenger seat adult occupants who are properly seated and using the seat belt as outlined in this manual should not cause the
front passenger air bag to be automatically turned OFF. For small adults it may be turned OFF, however if the occupant takes his/her
weight off the seat cushion (for example, by not sitting upright, by sitting on an edge of the seat, or by otherwise being out of position),
this could cause the sensor to turn the air bag OFF. Always be sure to be seated and wearing the seat belt properly for the most effective
protection by the seat belt and supplemental air bag.
If additional forces are applied to the seat, the system may interpret the occupant’s weight as lower than it actually is.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Have the occupant on the front-passenger seat step out of the vehicle.
5. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
6. Observe the indicator lights in the center console and the vehicle information display and check the following.
Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator lights must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section)
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
2-38Instruments and controls

MessagePossible causes/consequences and solutions
[Front Passenger Airbag
Enabled See Operator’s
Manual] The front-passenger front air bag is enabled during the journey although:
•A child or child restraint as specified in U.S. regulations is located on the front-passenger seat.
or
•The front-passenger seat is not occupied.
The system may detect objects or forces that are adding to the weight applied to the seat.
1. Stop the vehicle in a safe area away from traffic as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Switch the ignition off.
4. Open the front-passenger door.
5. Remove the child and the child restraint system from the front passenger seat.
6. Make sure there are no objects applying additional force to the seat. The system may otherwise detect the additional force and interpret the seat occupant’s weight as greater than it actually is.
7. Make sure that the seat is unoccupied, close the front passenger door and switch on the ignition.
8. Observe the indicator lights in the center console and the vehicle information display and check the following. Seat unoccupied and ignition switched on:
- The and indicator lights must light up simultaneously for approximately six
seconds.
- The indicator light must then light up and remain lit. If the indicator light is on, the automatic
front-passenger front air bag deactivation system has disabled the front-passenger front air bag (see Front passenger air bag and
status light in the1. Safety — seats, seat belts and supplemental restraint system section).
- the [Front Passenger Airbag Enabled See Operator’s Manual] or [Front Passenger Airbag Disabled See Operator’s Manual] display
messages must not be shown in the vehicle information display.
7. Wait for a period of at least 60 seconds until the necessary system checks have been completed.
8. Make sure that the display messages do not appear in the vehicle information display.
If these conditions are met, the front-passenger seat can be occupied again. Whether the or indicator
light remains lit or goes out depends on how the automatic front passenger front air bag deactivation system classifies the occupant.
If the conditions are not met, the system is not operating correctly.
Have the system checked immediately. It is recommended you visit an INFINITI retailer for this service.
For further information on the automatic front-passenger front air bag deactivation feature (see Front passenger air bag and status light
in the 1. Safety — seats, seat belts and supplemental restraint system section).
Instruments and controls2-39

•If any malfunctions are found or the heated
seat does not operate, turn the switch off
and have the system checked. It is recom-
mended you visit an INFINITI retailer for this
service.The front seats are warmed by built-in heaters.
The switches are located on the center console
and can be operated independently, for the
left-hand side seat and for the right-hand side
seat.
The three red indicator lights in the button
indicate the heating level you have selected The
system automatically switches from level 3 to
level 2 after approximately eight minutes The
system automatically switches from level 2 to
level 1 after approximately ten minutes. The
system automatically switches off approxi-
mately 20 minutes after it is set to level 1. 1. Turn the ignition switch to the ON position.
NOTE
The seat heater can only be activated when
the ignition switch is in the ON position.
2. Start the engine.
3. Select the heat range:
•To switch on: press button1repeatedly
until the desired heating level is set.
•To switch off: press button1repeatedly
until all the indicator lights turn off.
NOTE
If the battery voltage is too low, the seat heating
may switch off.NIC2634
Instruments and controls2-71

Opening and closing
Manual control:
To close the sunshade, press and hold the
“CLOSE” side of the switch
1To stop the
sunshade from closing fully, release the switch.
To open the sunshade press and hold the
“OPEN” side of the switch
2To stop the
sunshade from opening fully, release the
switch.
Automatic operation
:
To fully open or close the sunshade automati-
cally, press briefly on the open or close side of
the switch and then release. To stop the sun-
shade from opening or closing, press either
side of the switch.
Auto-reverse function
:
When the control unit detects something caught
by the sunshade, the sunshade will open auto-
matically.
NOTE
The auto-reverse function remains active
whether the sunshade is being closed manually
or automatically. If the battery cable is disconnected, the clock
will need to be re-adjusted to the correct time.
ADJUSTING TIME
Set the time using the INFINITI controller and
the [Settings] menu available in the central
display (see
Clock settings in the4. Display
screen, heater and air conditioner, and audio
system section).
NOTE
On vehicles fitted with a navigation system, the
clock is automatically updated via GPS. The ini-
tial clock setting may be incorrect.
In the center console (LHD)
Rear console
NSD619NIC2690
NIC2683
CLOCK POWER OUTLET
2-76Instruments and controls

– CDs with a paper label
– CDs that are warped, scratched, or haveabnormal edges
•This audio system can only play prerecorded
CDs. It has no capabilities to record or burn
CDs.
•If a CD cannot be played, one of the following
messages will be displayed.
[Disc Reading Error]
Indicates a CLV/Focus, TOC or Access error.
Check and re-insert the CD. Make sure that it
is inserted correctly.
[Please Eject Disc]
Indicates a mechanism error. If the CD can be
ejected, eject and re-insert the CD. If the CD
cannot be ejected, have the system checked.
It if recommended you contact an INFINITI
retailer for this service.
[File type is not supported]
Indicates that no readable files are found on
the inserted CD. Check the data on your CD.
USB (Universal Serial Bus) connection
port/ iPod
The Media Hub is located in the center console
and consists of the USB connectors. 1) USB/iPod connection port
Connect to play media from an iPod
R,
iPhone
Ror a USB memory device. When
using INFINITI InTouch Apps with an
iPhone
R, connect via a USB cable. Refer to
the device manufacturer’s owner information
regarding the proper use and care of the
device.
WARNING
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION
•Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is con-
nected correctly into the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
•Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
The vehicle is not equipped with a USB device.
USB devices should be purchased separately as
necessary.
This system cannot be used to format USB
devices. To format a USB device, use a personal
computer.
In some areas, the USB device for the front
seats plays only sound without images for
regulatory reasons, even when the vehicle is
parked.
This system supports various USB memory de-
vices, USB hard drives and iPod players. Some
NAA1628
4-56Display screen, heater and air conditioner, and audio system

CAUTION
•Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side down into the port may damage the
port. Make sure that the USB device is con-
nected correctly to the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
•Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Two USB connectors are located on the center
console box.
USB (Universal Serial Bus) connection port/
iPod page 4-56
When compatible storage devices are plugged
into the jack, compatible audio files on the
storage devices can be played through the
vehicle’s audio system.
How to view USB operation screen
1[Source]:
Touch to switch to the source list screen.
Selecting audio source page 4-65
2Play time:
The play time of the track is displayed.
3Track information:
Track information such as the song title,
artist name and folder name is displayed.
4Audio source indicator:
Indicates which of the two USB memory
device is selected.
NAA1719
4-72Display screen, heater and air conditioner, and audio system