2017 INFINITI QX30 tire type

SMALL CHILDREN
Children that are over 1 year old and weigh at
least 20 lbs (9 kg) should remain in a rear-
facing child restraint as long as possible up to
the height or weight limit of the child restraint.
Children who outgrow the height or weight limit
of the rear-facing child restraint and are at least
1 year old should be secured in a forward-facing
child restraint with a harness. Refer to the
manufacturer’s instructions for minimum and
maximum weight and height recommendations.
INFINITI recommends that small children be
placed in child restraints that comply with
Federal Motor Vehicle Safety Standards or Ca-
nadian Motor Vehicle Safety Standards. You
should choose a child restraint that fits your
vehicle and always follow the manufacturer’s
instructions for installation and use.
LARGER CHILDREN
Children should remain in a forward-facing
child restraint with a harness until they reach
the maximum height or weight limit allowed by
the child restraint manufacturer.
Children who are too large for child restraints
should be seated and restrained by the seat
belts which are provided. The seat belt may not
fit properly if the child is less than 4 ft 9 in
(142.5 cm) tall and weighs between 40 lbs(18 kg) and 80 lbs (36 kg). A booster seat
should be used to obtain proper seat belt fit.
Once a child outgrows the height or weight limit
of the harness-equipped forward-facing child
restraint, INFINITI recommends that the child be
placed in a commercially available booster seat
to obtain proper seat belt fit. For a seat belt to
fit properly, the booster seat should raise the
child so that the shoulder belt is properly
positioned across the chest and the top, middle
portion of the shoulder. The shoulder belt
should not cross the neck or face and should
not fall off the shoulder. The lap belt should lie
snugly across the lower hips or upper thighs,
not the abdomen. A booster seat can only be
used in seating positions that have a three-
point type seat belt. The booster seat should fit
the vehicle seat and have a label certifying that
it complies with Federal Motor Vehicle Safety
Standards or Canadian Motor Vehicle Safety
Standards.
A booster seat should be used until the child
can pass the seat belt fit test below:
•Are the child’s back and hips against the
vehicle seatback?
•Is the child able to sit without slouching?
•Do the child’s knees bend easily over the
front edge of the seat with feet flat on the
floor?
•Can the child safely wear the seat belt (lap
belt low and snug across the hips and shoul-
der belt across mid-chest and shoulder)?
•Is the child able to use the properly adjusted
head restraint/headrest?
•Will the child be able to stay in position for
the entire ride?
If you answered no to any of these questions,
the child should remain in a booster seat using
a three-point type seat belt.
NOTE
Laws in some communities may follow different
guidelines. Check local and state regulations to
confirm your child is using the correct restraint
system before traveling.
WARNING
Never let a child stand or kneel on any seat and
do not allow a child in the cargo area. The child
could be seriously injured or killed in a sudden
stop or collision.
Safety — seats, seat belts and supplemental restraint system1-19

If you wish to confirm the restart:
5. Press to confirm.The [Tire Press. Monitor Restarted] message
appears in the vehicle information display.
After you have driven for a few minutes, the
system checks whether the current tire pres-
sures are within the specified range The new
tire pressures are then accepted as refer-
ence values and monitored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher roll-
over rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of perform-
ing in a variety of on-pavement and off-road
applications. This gives them a higher center of
gravity than ordinary vehicles. An advantage of
higher ground clearance is a better view of the
road, allowing you to anticipate problems. How-
ever, they are not designed for cornering at the
same speeds as conventional 2-wheel drive
vehicles any more than low-slung sports cars
are designed to perform satisfactorily underoff-road conditions. If at all possible, avoid
sharp turns at high speeds. As with other
vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or
vehicle rollover. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt.
For additional information, refer to
Driving
safety precautions later in this section.
AVOIDING COLLISION AND ROLLOVER
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of control or
an accident.
Be alert and drive defensively at all times. Obey
all traffic regulations. Avoid excessive speed,
high speed cornering, or sudden steering ma-
neuvers, because these driving practices could
cause you to lose control of your vehicle.
As with any vehicle, loss of control could result
in a collision with other vehicles or objects or
cause the vehicle to roll over, particularly if the
loss of control causes the vehicle to slide side-
ways. Be attentive at all times, and avoid
driving when tired. Never drive when under the
5-10Starting and driving

Always back straight down in R (Reverse)
gear and apply brakes to control your
speed.
•Heavy braking going down a hill could cause
your brakes to overheat and fade, resulting
in loss of control and an accident. Apply
brakes lightly and use a low gear to control
your speed.
•Unsecured cargo can be thrown around
when driving over rough terrain. Properly
secure all cargo so it will not be thrown
forward and cause injury to you or your pas-
sengers.
•Secure heavy loads in the cargo area as far
forward and as low as possible. Do not
equip the vehicle with tires larger than
specified in this manual. This could cause
your vehicle to roll over.
•Do not grip the inside or spokes of the steer-
ing wheel when driving off-road. The steer-
ing wheel could move suddenly and injure
your hands. Instead drive with your fingers
and thumbs on the outside of the rim.
•Before operating the vehicle, ensure that
the driver and all passengers have their seat
belts fastened.
•Always drive with the floor mats in place as
the floor may become hot.
•Lower your speed when encountering
strong crosswinds. With a higher center of
gravity, your INFINITI is more affected by
strong side winds. Slower speeds ensure
better vehicle control.
•Do not drive beyond the performance capa-
bility of the tires, even with AWD engaged.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpectedvehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel ex-
cessively.
•Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•If at all possible, avoid sharp turning ma-
neuvers, particularly at high speeds. Your
INFINITI vehicle has a higher center of grav-
ity than a passenger car. The vehicle is not
designed for cornering at the same speeds
as passenger cars. Failure to operate this
vehicle correctly could result in loss of con-
trol and/or a rollover accident.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted, or
radial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•Be sure to check the brakes immediately
after driving in mud or water.
Starting and driving5-13

•Avoid parking your vehicle on steep hills. If
you get out of the vehicle and it rolls for-
ward, backward or sideways, you could be
injured.
•Whenever you drive off-road through sand,
mud or water as deep as the wheel hub,
more frequent maintenance may be re-
quired. For additional information, refer to
Maintenance schedulesin the
9. Maintenance and Schedules section.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS (IF SO
EQUIPPED)
WARNING
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•This vehicle is not designed for offroad
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any D (Drive) or R (Re-
verse) position with the engine running. Do-
ing so may result in drivetrain damage or
unexpected vehicle movement which could
result in serious vehicle damage or personal
injury
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer, (such
as the dynamometers used by some states
for emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpected
vehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively. The INFINITI Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll road
device or automated payment device on the key
ring. Restart the engine using the following
procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK position and wait approximately 5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the device (which may have caused the interference)
separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
INFINITI VEHICLE IMMOBILIZER SYSTEM
5-14Starting and driving

6.Avoid Idling
•Shutting off your engine when safe for
stops exceeding 30 seconds saves fuel
and reduces emissions.
7. Buy an Automated Pass for Toll Roads
•Automated passes permit drivers to use
special lanes to maintain cruising speed
through the toll and avoid stopping and
starting.
8. Winter Warm Up
•Limit idling time to minimize impact to
fuel economy.
•Vehicles typically need no more than 30
seconds of idling at start-up to effectively
circulate the engine oil before driving.
•Your vehicle will reach its ideal operating
temperature more quickly while driving
versus idling.
9. Keeping your Vehicle Cool
•Park your vehicle in a covered parking
area or in the shade whenever possible.
•When entering a hot vehicle, opening the
windows will help to reduce the inside
temperature faster, resulting in reduced
demand on your A/C system.
•Keep your engine tuned up.
•Follow the recommended scheduled mainte-
nance.
•Keep the tires inflated to the correct pres-
sure. Low tire pressure increases tire wear
and lowers fuel economy.
•Keep all the wheels in correct alignment.
Improper alignment increases tire wear and
lowers fuel economy.
•Use the recommended viscosity engine oil.
For additional information, see Recom-
mended fluids/lubricants and capacities in
the 10. Technical information section
WARNING
•Do not drive beyond the performance capa-
bility of the tires, even with 4WD engaged.
Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
•This vehicle is not designed for off-road
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For 4WD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test a 4WD equipped ve-
hicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing) or similar equipment
even if the other two wheels are raised off
the ground. Make sure that you inform the
test facility personnel that your vehicle is
INCREASING FUEL ECONOMY FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED)
Starting and driving5-83

slight pulsation. This is normal and indicates
that the Brake Assist System is operating (if
equipped).
Using brakes
Avoid resting your foot on the brake pedal while
driving. This will overheat the brakes, wear out
the brake linings/pads faster, and increase fuel
consumption.
To help reduce brake wear and to prevent the
brakes from overheating, reduce speed and
downshift to a lower gear before going down a
slope or long grade. Overheated brakes may
reduce braking performance and could result in
loss of vehicle control.
While driving on a slippery surface, be careful
when braking, accelerating or downshifting.
Abrupt braking or acceleration could cause the
wheels to skid and result in an accident.
Wet brakes
When the vehicle is washed or driven through
water, the brakes may get wet. As a result, your
braking distance will be longer and the vehicle
may pull to one side during braking.
To dry the brakes, drive the vehicle at a safe
speed while lightly depressing the brake pedal
to heat up the brakes. Do this until the brakesreturn to normal. Avoid driving the vehicle at
high speeds until the brakes function correctly.
Driving uphill
When starting on a steep gradient, it is some-
times difficult to operate the brake. Use the
parking brake to hold the vehicle. When ready
to start, make sure that the shift lever is in an
appropriate forward or reverse driving position,
release the parking brake while depressing the
accelerator pedal. If your vehicle has an electric
parking brake, this will automatically release
when you depress the accelerator pedal (DCT
models).
Driving downhill
The engine braking action is effective for con-
trolling the vehicle while descending hills.
A low gear position in the manual shift mode,
low enough to obtain sufficient engine braking,
should be selected.
Parking brake break-in
Break in the parking brake shoes whenever the
stopping effect of the parking brake is weak-
ened or whenever the parking brake shoes
and/or drums/rotors are replaced, in order to
assure the best braking performance.
This procedure is described in the vehicle ser-
vice manual and can be performed by an
INFINITI retailer.
ANTI-LOCK BRAKING SYSTEM (ABS)
WARNING
The Anti-lock Braking System (ABS) is a so-
phisticated device, but it cannot prevent acci-
dents resulting from careless or dangerous
driving techniques. It can help maintain ve-
hicle control during braking on slippery sur-
faces. Remember that stopping distances on
slippery surfaces will be longer than on normal
surfaces even with ABS. Stopping distances
may also be longer on rough, gravel or snow
covered roads, or if you are using tire chains.
Always maintain a safe distance from the ve-
hicle in front of you. Ultimately, the driver is
responsible for safety.
Tire type and condition may also affect braking
effectiveness.
– When replacing tires, install the specified
size of tires on all four wheels.
– When installing a replacement tire, make sure
that it is the proper size and type as specified
on the tire and loading information label. (See
5-88Starting and driving

coolantin the8. Do-it-yourself section of this
manual.
TIRE EQUIPMENT
1. SUMMER tires have a tread designed to provide superior performance on dry pave-
ment. However, the performance of these
tires will be substantially reduced in snowy
and icy conditions. If you operate your ve-
hicle on snowy or icy roads, INFINITI recom-
mends the use of MUD & SNOW or ALL
SEASON TIRES on all four wheels. It is rec-
ommended that you visit an INFINITI retailer
for the tire type, size, speed rating and
availability information.
2. For additional traction on icy roads, studded tires may be used. However, some U.S.
states and Canadian provinces prohibit their
use. Check local, state and provincial laws
before installing studded tires.
Skid and traction capabilities of studded snow
tires, on wet or dry surfaces, may be poorer than
that of non-studded snow tires.
3. Tire chains may be used if desired. Make sure they are the proper size for the tires on
your vehicle and are installed according to
the chain manufacturer’s instructions. Use
chain tensioners when recommended by the
tire chain manufacturer to ensure a tight fit. Loose end links of the tire chains must be
secured or removed to prevent the possibil-
ity of whipping action damage to the fenders
or underbody. In addition, drive at a reduced
speed, otherwise, your vehicle may be dam-
aged and/or vehicle handling and perfor-
mance may be adversely affected.
SPECIAL WINTER EQUIPMENT
It is recommended that the following items be
carried in the vehicle during the winter:
•A scraper and stiff-bristled brush to remove
ice and snow from the windows.
•A sturdy, flat board to be placed under the
jack to give it firm support.
•A shovel to dig the vehicle out of snowdrifts.
•Extra washer fluid to refill the windshield
washer fluid reservoir.
DRIVING ON SNOW OR ICE
WARNING
•Wet ice (32°F, 0°C and freezing rain), very
cold snow or ice can be slick and very hard
to drive on. The vehicle will have much less
traction or “grip” under these conditions.
Try to avoid driving on wet ice until the road
is salted or sanded.
•Whatever the condition, drive with caution.
Accelerate and slow down with care. If ac-
celerating or downshifting too fast, the
drive wheels will lose even more traction.
•Allow more stopping distance under these
conditions. Braking should be started
sooner than on dry pavement.
•Allow greater following distances on slip-
pery roads.
•Watch for slippery spots (glare ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while on the ice, and avoid any sudden
steering maneuvers.
•Do not use cruise control on slippery roads.
•Snow can trap dangerous exhaust gas un-
der your vehicle. Keep snow clear of the
exhaust pipe and from around your vehicle.
5-94Starting and driving

In addition to the vehicle load, the driving
distance possible depends upon:
•Vehicle speed.
•Road condition.
•Outside temperature.
The driving distance possible in run-flat mode
may be reduced by extreme driving conditions/
maneuvers, or it can be increased through a
moderate style of driving.
The driving distance possible in run-flat mode is
counted from the moment the tire pressure loss
warning appears in the vehicle information dis-
play.
You must not exceed a maximum speed of 50
MPH (80 km/h).
When replacing one or all tires, observe the
following specifications for your vehicle’s tires:
•Size
•Type
•Run-flat mark
If a tire has gone flat and cannot be replaced
with a run flat tire, a standard tire may be used
as a temporary measure. Make sure that you
use the proper size and type (summer or winter
tire).
WARNING
Do not exceed the stated maximum speed.
Avoid abrupt steering and driving maneuvers,
and driving over obstacles (curbs, pot holes,
off road). This applies in particular to a laden
vehicle.
Stop driving in emergency mode if:
•You hear banging noises.
•The vehicle starts to shake.
•You see smoke and smell rubber.
•VDC is intervening constantly.
•There are tears in the sidewalls of the tire.
After driving in emergency mode, have the
wheel rims checked with regard to their further
use. It is recommended you visit an INFINITI
retailer for this service. The faulty tire must be
replaced.
REMOVING AND FITTING WHEELS
NOTE
A spare wheel is not provided with your vehicle.
Blocking the wheels
WARNING
Make sure to block the appropriate wheel to
prevent the vehicle from moving, which may
cause personal injury.
Place suitable blocks
1in front of and behind
the wheel diagonally opposite the flat tire
Ato
prevent the vehicle from moving when it is on
the jack.
MCE0001DZ
In case of emergency6-5