2017 INFINITI QX30 radio antenna

FM radio reception
MAXIMUM SIGNAL DISTANCES
•FM : 25 to 30 miles (40 to 48 km)
•AM : 60 to 130 miles (97 to 209 km)
Range: FM range is normally limited to 25 to 30
miles (40 to 48 km), with monaural (single
station) FM having slightly more range than
stereo FM. External influences may sometimes
interfere with FM station reception even if the
FM station is within 25 miles (40 km). The
strength of the FM signal is directly related to
the distance between the transmitter and re-
ceiver. FM signals follow a line-of-sight path,
exhibiting many of the same characteristics as
light. For example they will reflect off objects. Fade and drift: As your vehicle moves away from
a station transmitter, the signals will tend to
fade and/or drift.
Static and flutter: During signal interference
from buildings, large hills or due to antenna
position, usually in conjunction with an in-
creased distance from the station transmitter,
static or flutter can be heard. This can be
reduced by lowering the treble setting to reduce
the treble response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.AM radio reception
AM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can bounce off the
ionosphere and be bent back to earth. Because
of these characteristics, AM signals are also
subject to interference as they travel from trans-
mitter to receiver.
Fading: This occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.Static: Caused by thunderstorms, electrical
power lines, electric signs and even traffic
lights.
HD RadioTMTechnology reception
(for U.S.)
HD RadioTMTechnology reception needs to be
activated to receive HD Radio broadcasts, see
Audio settings later in this section.
This enables you to receive radio broadcasts
digitally (where available), providing a better
quality sound with clear reception. When this
feature is not activated or HD Radio broadcasts
are not available, you will receive analog radio
(AM/FM) broadcasts.
Satellite radio reception
When the satellite radio is used for the first time
or the battery has been replaced, the satellite
radio may not work properly. This is not a
malfunction. Wait more than 10 minutes with
the satellite radio ON and the vehicle outside of
any metal or large building for the satellite
radio to receive all of the necessary data.
The satellite radio requires an active SiriusXM
Satellite Radio subscription. The satellite ser-
vice is a available only to those at least 18 and
older in the 48 contiguous United States.
SAA0306Z
Display screen, heater and air conditioner, and audio system4-53

The satellite radio performance may be affected
if cargo carried on the roof blocks the satellite
radio signal.
If possible, do not put cargo near the satellite
antenna.
The build up of ice on the satellite radio an-
tenna can affect satellite radio performance.
Remove the ice to restore satellite radio recep-
tion.
Trademarks
HD Radio Technology manufactured under li-
cense from iBiuity Digital Corporation. U.S. and
Foreign Patents. HD Radio
TMand the HD, HD
Radio, and “Arc” logos are proprietary trade-
marks of iBiquity Digita; Corp.
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
SiriusXM services require a subscription after
trial period and are sold separately or as a package. Our satellite service is available only
to those at least 18 and older in the 48 contigu-
ous USA and DC. For more information visit
www.siriusxm.com.
Required SiriusXM Satellite Radio and SiriusXM
Travel Link monthly subscriptions are sold
separately. Sirius XM Travel Link is only avail-
able in select markets. For more information,
see www.sirius.com/travellink
“Made for iPodR” and “Made for iPhoneR”
mean that an electronic accessory has been
designed to connect specifically to iPod
Ror
iPhone
R, respectively, and has been certified
by the developer to meet Apple performance
standards. Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note
that the use of this accessory with iPod
Ror
iPhone
Rmay affect wireless performance.
Apple, the Apple logo, iPhone
R, iPodR, iPod
classic
R, iPod nanoR, and iPod touchRare trademarks of Apple Inc., registered in the
U.S. and other countries. Lightning is a trade-
mark of Apple Inc. App Store is a service mark of
Apple Inc.
Music recognition technology and related data
are provided by Gracenote®. Gracenote is the
industry standard in music recognition technol-
ogy and related content delivery. For more
information, visit www.gracenote.com.
CD and music-related data from Gracenote, Inc.,
copyright
c2000 to present Gracenote.
Gracenote Software, copyright
c2000 to pres-
ent Gracenote. One or more patents owned by
Gracenote apply to this product and service.
See the Gracenote website for a non-exhaustive
list of applicable Gracenote patents. Gracenote,
CDDB, MusicID, MediaVOCS, the Gracenote
logo and logotype, and the “Powered by
Gracenote” logo are either registered trade-
marks or trademarks of Gracenote in the United
States and/or other countries.
App Store
SM
Apple and the Apple logo are trademarks of
Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of Apple
Inc.
Google Play
TM
Google Play is a trademark of Google Inc.
4-54Display screen, heater and air conditioner, and audio system

system. This connection allows you to listen to
the audio from the Bluetooth® device using
your vehicle speakers. It may also allow basic
control of the device for playing and skipping
audio files using the AVRCP Bluetooth® profile.
Not all Bluetooth® devices have the same level
of controls for AVRCP. Please consult the
manual for your Bluetooth® device for more
details.
Wireless LAN (Wi-Fi) and the Bluetooth® func-
tions share the same frequency band (2.4 GHz).
Using the Bluetooth® and the wireless LAN
functions at the same time may slow down or
disconnect the communication and cause unde-
sired noise. It is recommended that you turn off
the wireless LAN (Wi-Fi) when using the
Bluetooth® functions.
Regulatory Information
FCC Regulatory information:
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled envi-
ronment and meets the FCC radio frequency (RF)
Exposure Guidelines. This equipment has very
low levels of RF energy that it deemed to comply
without maximum permissive exposure evalua-
tion (MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
IC Regulatory information
:
The antenna cannot be removed (and changed)
by user.
NOTE: This device complies Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.CAUTION : Radio Frequency Radiation Exposure
This equipment complies with IC radiation ex-
posure limits set forth for uncontrolled environ-
ment and meets RSS-102 of the IC radio fre-
quency (RF) exposure rules. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at least
20cm and more between the radiator and per-
son’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
This Class B digital apparatus meets all require-
ments of the Canadian Interference Causing
Equipment Regulations.
Connecting Bluetooth® streaming
audio device
Bluetooth® streaming audio device must be
connected to the vehicle before operation.
Connecting Bluetooth® device page 4-88
Display screen, heater and air conditioner, and audio system4-77

•Some Bluetooth® enabled cellular phones
may not be recognized by the in-vehicle
phone module. Please visit
www.infinitiusa.com/bluetooth and search
for a recommended phone list.
•You will not be able to use a hands-free
phone under the following conditions:– Your vehicle is outside the service area for your cellular phone network.
– Your vehicle is in an area where it is difficult to receive radio waves, such as in
a tunnel, in an underground parking ga-
rage, behind a tall building or in a moun-
tainous area.
– Your cellular phone is locked in order to prevent dialing.
•When the radio wave condition is not ideal or
ambient sound is too loud, it may be difficult
to hear the other person’s voice during a call.
•This Bluetooth® system supports Wideband
speech, which enhances the sound quality of
phone calls placed over Bluetooth®. To take
advantage of this feature, the cellular device
should be used on a carrier supporting Adap-
tive Multi-Rate Wideband (AMR-WB) or HD
voice technology. The performance of
AMR-WB may vary by carrier and calling area.
Consult your cellular carrier if you experience
issues with call quality or connection.
•Immediately after the ignition switch is
turned ON, it may be impossible to receive a
call for a short period of time.
•Do not place the cellular phone in an area
surrounded by metal or far away from the
in-vehicle phone module to prevent tone
quality degradation and wireless connection
disruption.
•While a cellular phone is connected through
the Bluetooth® wireless connection, the bat-
tery of the cellular phone may discharge
quicker than usual.
•If the Bluetooth® Hands-Free Phone System
seems to be malfunctioning, please visit
www.infinitiusa.com/bluetooth for trouble-
shooting help.
•Some cellular phones or other devices may
cause interference or a buzzing noise to be
emitted from the audio system speakers.
Storing the device in a different location may
reduce or eliminate the noise.
•Refer to the owner’s manual for the cellular
phone for information regarding the tele-
phone pairing procedure specific to your
phone, battery charging, and cellular phone
antenna, etc.
•The antenna display on the monitor may not
match the antenna display of some cellular
phones.
•The battery display on the monitor may not
match the battery display of some cellular
phones.
•Keep the interior of the vehicle as quiet as
possible to hear the caller’s voice clearly as
well as to minimize echoes.
•If reception between callers is unclear, ad-
justing the incoming or outgoing call volume
may improve the clarity.
REGULATORY INFORMATION
FCC Regulatory Information
FCC ID : HYQDNNS075
NOTE: This device complies with part 15 of the
FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including in-
terference that may cause undesired operation.
FCC WARNING: Changes or modifications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
4-84Display screen, heater and air conditioner, and audio system

CAUTION : Radio Frequency Radiation Exposure
This equipment complies with FCC radiation
exposure limits set forth for uncontrolled envi-
ronment and meets the FCC radio frequency (RF)
Exposure Guidelines. This equipment has very
low levels of RF energy that it deemed to comply
without maximum permissive exposure evalua-
tion (MPE). But it is desirable that it should be
installed and operated with at least 20cm and
more between the radiator and person’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
IC Regulatory information
The antenna cannot be removed (and changed)
by user.
NOTE: This device complies Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
CAUTION : Radio Frequency Radiation Exposure
This equipment complies with IC radiation ex-
posure limits set forth for uncontrolled environ-
ment and meets RSS-102 of the IC radio fre-quency (RF) exposure rules. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it
should be installed and operated with at least
20cm and more between the radiator and per-
son’s body.
Co-location: This transmitter must not be co-
located or operated in conjunction with any
other antenna or transmitter.
This Class B digital apparatus meets all require-
ments of the Canadian Interference Causing
Equipment Regulations.The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
PHONE
Connecting Bluetooth® Hands-Free
Phone
The cellular phone must be connected to the
Bluetooth® Hands-Free Phone System before
commencing operation. Up to 5 cellular phones
can be connected to the system.
See
Connecting Bluetooth® device later in
this section
Phone selection
Select one of the connected devices for opera-
tion.
1. Push

SymptomPossible cause Possible solution
Each volume level (ring tone, incoming voice or outgoing voice) is different. Each volume level is not adjusted properly.
Adjust each volume level properly.
The antenna display is different between the
navigation screen (if equipped) and the screen on a cellular phone. Making or receiving a call
is unavailable even though the antenna display indicates that it is possible to do so. The antenna display varies depending on the model
of cellular phone. This does not indicate a malfunction. The antenna display
and remaining battery level shown on the navigation
screen may be different from those shown on the cellular phone screen. Use them as a reference.
A voice cannot be heard clearly when using a cellular phone behind tall buildings. Some structures such as tall buildings, etc. may
cause irregular reflection of radio waves or completely shut out radio waves that are used for cellular phones. This is not a malfunction.
Noise is heard when using a cellular phone
under/near areas of elevated railroads, high
voltage electric power cables, traffic signals, or neon billboards, etc. Electromagnetic waves that are generated from radio
devices may adversely affect the cellular phone. This is not a malfunction.
Noise is heard in the sound from the audio system while using a cellular phone. Radio waves that are generated from a cellular phone
may adversely affect the sound from the audio system. This is not a malfunction.
The sound skips. The cellular phone may have turned on the wireless
LAN (Wi-Fi). Turn off the wireless LAN (Wi-Fi).
Phonebook cannot be downloaded. An error occurred during the phone pairing process. Re-register the Bluetooth® pairing information after deleting the pairing information from both the cellularphone and the vehicle system.
Display screen, heater and air conditioner, and audio system4-133

REMOVING SPOTS
Remove tar and oil spots, industrial dust, in-
sects, and tree sap as quickly as possible from
the paint surface to avoid lasting damage or
staining. Special cleaning products are avail-
able at an INFINITI retailer or any automotive
accessory store.
UNDERBODY
In areas where road salt is used in the winter, it
is necessary to clean the vehicle’s underbody
regularly in order to prevent dirt and salt from
building up and causing the acceleration of
corrosion on the underbody and suspension.
Before the winter and again in the spring, the
underseal must be checked and, if necessary,
re-treated.
GLASS
Use glass cleaner to remove smoke and dust
film from the glass surfaces. It is normal for
glass to become coated with a film after the
vehicle is parked in the hot sun. Glass cleaner
and a soft cloth will easily remove this film.
CAUTION
When cleaning the inside of the windows, do
not use sharp-edged tools, abrasive cleaners
or chlorine-based disinfectant cleaners. They
could damage the electrical conductors, radio
antenna elements or rear window defroster
elements.
WHEELS
•Wash the wheels when washing the vehicle
to maintain their appearance.
•Clean the inner side of the wheels when the
wheel is changed or the underside of the
vehicle is washed.
•Do not use abrasive cleaners when washing
the wheels.
•Inspect wheel rims regularly for dents or
corrosion. This may cause loss of pressure or
damage the tire bead.
•INFINITI recommends that the road wheels be
waxed to protect against road salt in areas
where it is used during winter.
ALUMINUM ALLOY WHEELS
Wash the wheels regularly with a sponge damp-
ened in a mild soap solution, especially during
winter in areas where road salt is used. The salt
residue from road salt could discolor the wheels
if it is not washed off regularly.
CAUTION
Follow the directions below to avoid staining
or discoloring the wheels:
•Do not use a cleaner that uses strong acid or
alkali contents to clean the wheels.
•Do not apply wheel cleaners to the wheels
when they are hot. The wheel temperature
should be the same as ambient tempera-
ture.
•Rinse the wheel to completely remove the
cleaner within 15 minutes after the cleaner
is applied.
CHROME PARTS
Clean all chrome parts regularly with a nonabra-
sive chrome polish to maintain the finish.
Appearance and care7-3