2017 AUDI Q3 Owner´s Manual

00
00
......
"' ,....
"' ...... 0 0 :::,
00
A WARNING , ~ -
Have the malfunction in the safety systems
inspected immediately. Otherwise, there is a
r isk that the systems may not activate during
a collision, which increases the risk of serious
injury or death.
(0) Brake pads
Ei] Brake pad s!
The brake pads are worn .
Drive to an authorized Aud i dea ler or authorized
Audi Service Facility immediately to have the brake pads checked.
App lies to: USA models
The Ei] indicator light turns on together with the
1111 indicator light
EPC Engine control (gasoline engine)
Applies to: vehicl es with gasoline engines
If the 13:a indicator light turns on while driving,
there is an eng ine control malfunction.
Immediately drive slowly to an authorized Audi
dealer or authori zed Audi Service Facility to have
the malfunction corrected.
0 Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) is part of
the On Board Diagnostic system (OBD II). The
¢4 symbol turns on when the ign ition is switched
on and turns off again once the e ngine is started
and running at a steady id le speed . This indicates
that the MIL is functioning correctly.
The indicato r light turns on if there is a malfunc­
tion in the engine electronics. See an autho rized
Audi dealer or authorized Audi Service Facility to
have the ma lfunction corrected. For additiona l
information, see
~ page 17.
The indicator light can also turn on if the f uel fill­
e r cap is not closed correct ly
i::!> page 157.
Instruments and indicator lights
!"-" , Engine speed lim itation
Applies to: vehicles with engine speed limitation
(I! Maximum engine speed XXXX RPM
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheat ing .
The engine speed limitation deactivates once the engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once .
If the engine speed limitation was activated by
an engine control malfunction, the
13:a in dicator
light also turns on. Make sure that the speed
does not go above the speed displayed . Dr ive to
an authorized Aud i dea le r or authorized Audi
Service Facility immed iately to have the malfunc­
tion corrected.
~;. Engine oil
Ill Check oil level.
Refill engine oil as soon as possible i::!>page 162.
~ .,. Engine oil sensor
• Oil level sensor: System fault!
The sensor to check the eng ine o il level has
failed. Drive to an authorized Audi dealer or au­
thorized Aud i Serv ice Facility immediately to have
the malfunction cor rected.
i) Tank system
H Please refuel
If the indicator l ight turns on for the first time
and the message appears, there are about
1.8 -2.2 gallons ( 7.0 -8. S liters) of fuel left in the
tank .
H Fuel tank system malfunction! Contact deal­
er
Drive to an authorized Audi dealer or authorized
Audi Service Facility immed iately to have the
malfunction corrected. ..,.
15

Instruments and indicator lights
(D Tips
More informat ion on ref ueling is ava ila ble on
page
c::> page 156.
c:> Washer fluid level
A pp lies to: ve hicles w ith was her flu id level indicato r
Ill Please refill washer fluid
Fill the washer fluid with the ignition switched
off
c::> page 169.
~ Engine start system
i ·I 1-'.ngine start system: Malfunction! Please
contact dealer.
Do not switch the ignition off because you may
not be able to switc h it on aga in.
D rive to an a uth o riz e d Aud i de aler or a uth o riz ed
Aud i Serv ice Facility immedia tely to have the
malfunctio n corrected .
Engine start sy stem: Malfun ction . Plea se con ­
tact dealer .
There is a malfunc tion in the eng ine start ing sys­
tem.
Drive to an a uthorized Aud i dea ler or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
i§i Defective light bulb warning
If th e 1:J indica to r li ght turns on, a b ulb has
fa iled. The mess age in dicat es th e loca tion of the
bu lb .
Re plac e t he bulb immedia tely.
Vehicle lights: system fault!
There is a malfunction in the head lights or the
light switch.
D rive to an a uth o rized Aud i de aler or a uthorized
Aud i Serv ice Facility immediately to have t he
malfunct io n corrected .
16
A WARNING
-
-Light bulbs a re under p ressure and can ex­
plod e when b ulbs are replaced, wh ic h in ­
creases the risk of i nju ry .
- With HID headlights (xenon headlights) , the
high-vo ltage component must be handled
correctly . O th erwise, there is a r is k of fa tal
ln JUr y.
i.ID Headlight range control
II Headlight range control sy stem: system
fault!
There is a ma lf u nction in the headlight range
contro l system, which may cause gla re for other
drive rs.
Drive to an author ized A udi dealer or authorized
Audi Se rvice Facil ity immed iate ly to have the
malfunction correc ted.
go Audi adaptive light
App lies to: vehicles wi th Audi ada ptive light
r!iJ Audi adaptive light : system fault!
-
There is a ma lfunction in the adap tive lights. The
headlig hts st ill funct ion.
D rive to an authorized A udi dealer or authorized
Audi Se rvice Facility immediate ly to have the
malfunction corrected .
@.D Light/rain sensor
App lies to: vehicles wit h lig ht/ra in sensor
£1 Automatic headlights /wipers: System fault!
The light/rain sensor is malfunctioning.
The low beams remain sw itched on at all times
fo r safety reasons when the light switch is in the
AUTO position. Yo u can cont in u e to turn the
li ghts on and off us ing the lig ht switch. You can
sti ll contro l all fu nctions that are i ndependent of
the rain senso r thr ough the winds hield wiper lev­
e r.
D rive to an authorized A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction correc ted.

a:,
a:,
...... N r--. N .... 0 0 ::, a:,
; Adaptive dampers
App lies to: vehicles with Audi drive select and suspension con­
tro l
B Suspen sion: system fault !
There is an adaptive damper malf unction .
Drive to an aut hori zed Aud i dea le r o r a uthori zed
Audi Service Facility immediately to have the
malfunct ion corrected.
¢¢ Turn signals
If the II or i!I indicator light b links, the turn
signals are activated. If both indicator lights are
blinking, the emergency flashers are act ivated.
If an indicato r light blinks twice as fast as usua l,
a t urn signa l bulb has failed . Caref ully drive to an
author iz ed Audi dealer or author iz ed Audi Service
Facility immediately to have the malfunction cor­
rected.
¢1.~ Trailer turn signal assembly
The indica to r li ght II blinks when the turn sig­
n a l is used , if a traile r h as been p roperly connec t­
e d to the veh icle .
If one of the turn s ignal bulbs on the trailer is
bu rned out or defect ive, the indicator l igh t will
n o t bl ink when yo u use the tu rn s ign als.
(D Tips
For ve hicles with a trail er hitch that was in­
s talle d later accord ing to fa ctory spec ifica­
ti ons, the trailer tur n signal as sembly is actu ­
at ed.
/fJl~/c:5 Door , hood or luggage
compartment lid is open
IJ-If the ind icator light tu rns on, then one of
the doors is not closed.
&-\-If the ind icator light t urns on, then the hood
is not closed .
§-j-If the ind icator light tu rns o n, then the lug­
g age compartment lid is not closed .
Instruments and indicator lights
On Board Diagnostic
System (OBD)
Malfunction indicator lamp (MIL)
The ma lf u nction ind icator lamp (MI L) Ill in t he
inst rument cluste r is pa rt of the On Board D iag­
nostic System (OBD II).
T he w arning/i ndic ator lig ht tu rn s o n when the ig ­
nition is switche d on and tu rns off once the en­
gine is starte d and is running in idle at a stab le
speed. This indicates t hat the MIL is f unctioning
correctly.
If the light does not turn off after starting the
engine
or t urns on while driving, this may ind i­
cate there is a malfunction in the eng ine. If the
i ndicator tu rns on, the catalytic conve rter may be
damaged .
Drive
with reduced engine performance (avo id
high speeds for extended periods of t ime and/o r
fast acceleration) and have the malfu nction cor­
rected . See an author ized Audi dealer or author ­
ized Audi Service Facility .
The indicator may turn on if the e lectronic speed
limiter is faulty . For addit ional information, see
¢ page 18, Electronic speed limiter .
The MIL may also turn on if the fuel filler cap is
not closed correctly ¢
page 157.
On-Board Diagnostics
Fig. 5 Locat ion o f Data Link Connecto r (OLC)
On -Board Diagnostics mo nitors the components
of your emission control system . Each monitore d
I>-
17

Instruments and indicator lights
component in your engine system has been as ­
signed a code. In case of a ma lfunction, the com­
ponent w ill be identif ied and the fau lt stored as a
code in the control module memory.
The MI L light may a lso ill uminate if there is a
leak in the on-board f uel vapor recovery system.
If the light ill uminates after a refueling, stop the
veh icle and make sure the fuel filler cap is prop­
erly closed (on ly vehicles with gasoline engine)
¢ page 157 .
In order to make an accurate d iagnosis, the stor­
ed data can on ly be displayed using special diag­
nostic equipment (generic scan too l for 0BD) .
In order to connect the specia l diagnostic equip ­
ment, p ush the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release ¢
fig. 5.
Your authorized Audi dealer or qualified work­
shop can interpret the code and perform the nec­
essary repair.
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
Electronic speed limiter
Your veh icle may be facto ry equipped with ti res
that are r ated for a maxim um speed of 130 mph
(210 km/h) . This is less than the maxim um speed
of yo ur vehicle. To reduce the risk of sudden tire
fa ilur e and loss of control if the veh icle is operat­
ed at excessive speeds, your vehicle a lso has an
electronic speed limiter. The electronic speed lim iter prevents your vehicle from going faster
than the t ire speed rating . For more information
¢ page 171 .
If the engine contro l unit receives faulty vehicle
ro ad speed s ignals, the Malfunction Indicator
Lamp (MIL)
¢4 will illum inate . If this occurs,
contact the nearest authorized Audi dealer for
assistance .
18
A WARNING
--
Always observe the posted speed limits and
adjust your speed to suit preva iling road, traf­
fic and weather conditions. Never drive your
vehi cle faster than the maximum speed rating
of the ti res insta lled.

a:,
a:,
...... N r--. N
'"' 0 0 ::, a:,
Driver information
system
Overview
Applies to: ve hicles with driver information system
Fig. 6 Display on vehicles w it h driver information system
and mu ltifunction steering w heel*
~ N
0
::) CX) al
Driving information and vehicle settings are
shown in the instrument cluster display. The type
of display and the contents depend on the vehicle
eq uipment.
Depending on the vehicle equipment, the driver
information system is controlled with either the
buttons on the windshield wiper lever*
i::> page 19or with the buttons on the mult i­
function steering wheel*
c:> page 19.
On vehicles w ith a multifunction steering wheel*,
the information @ is shown in tabs @. The tabs
are visible as soon as yo u press a button on the
multifunction steering wheel*.
The instrument cluster display provides informa­
tion about :
® Time and date c:> page 9
Digita l speedometer
On -board computer
i::> page 20
Efficiency program ¢page 21
Reduced display *
Indicator lights and messages
¢page 10
Service interval display c:> page 170
Cruise control system*
Parking aid*
Aud io*
Telephone* Navigation*
Driver in forma tion system
© Odometer and trip odometer (only in the
first tab*)
<::>p age 10
@ Outside temperature ¢ page 9, selector
l ever posit ion
(D Tips
- Yo u can set the units used for temperature,
speed and other measurements in the Info ­
tainment system.
- For information on the audio and naviga­
tion* functions, refer to the separate Info­
tainment system owner's manual.
Operation
Operating using the windshield wiper lever
Appl ies to: vehicles with driver information system without
multifu nction steer ing wheel
-------- ®
Fig. 7 Windshield wiper lever: operating the driver infor ­
ma tion system
Operating
• Switch the ignition on . The last select function
is displayed.
• To switch betwee n the on-board computer
0,
fJ , the efficiency program ii or, for example,
the cruise contro l system*, press the
I RESET I
button @.
• To access additiona l information below or
above, press the button @ down or up .
Recalling indicator lights and messages
• Press the !RESET I button @.
Resetting values to zero
• Select a value in the desired trip computer or in
the efficiency program. ..,.
19

Driver information system
• Press and hold the I RESET I button @for at
least one second . All values in the selected on­
board computer or in the efficiency program
are reset to zero.
Operating using the multifunction steering
wheel
A pp lies to: ve hicles w ith driver information system and multi­
fun ction s teeri ng w hee l
Fig. 8 Mult ifunction steering wheel: operat ing the drive r
i nfo rmation system
The tab@¢ page 19, fig. 6 appears once you
press a button on the mult ifunction steering
wheel.
Operating
,-.. ~ N
0
Cl • Switch the ignition on. The last select function
is d isp layed.
• To switch between the tabs, press the button
(D to the left or right~ fig. 8.
• To access additional information below or
above, turn the thumbwheel @down or up.
• To confirm a selection, press the t humbwheel
@ .
Opening Car functions
• Se lect the first tab with the button (D .
• Press the button @. Th e Car functions menu is
displayed .
• To se lect a menu item, turn and press the
thu mbwheel @.
• To se lect a function programmed to a steering
wheel button, press the button
@ .
Resetting values to zero
• In the Car functions me nu, select On-board
computer or Efficiency program.
20 •
Select a value in the desired trip computer or in
the efficiency program.
• To reset the va lues in a memory, press and hold
the thumbwheel @for one second.
Assigning a function to a programmable
steering wheel button
• Select the ICAR I button> (Car) Systems* con­
trol button >
Vehicle settings > Steering wheel
button .
Recalling indicator lights and messages
• Select the D tab.
The
D tab is on ly visible when there is at least
one indicator light or message displayed. Ot her
folders are only v is ib le if the applicable system is
switched on .
On-board computer
Applies to: vehicles wi th on -boa rd comp uter
Fig. 9 Display: on -boa rd computer memory level 1
Operating with the windshield wiper lever*
• Press the I RESET I button @ ¢ page 19, fig. 7
repeatedly until the on-board computer ap­
pears in the disp lay.
• To access add itiona l content, press the button
®·
Operating with the multifunction steering
wheel*
• Open Car functions and select the On-board
computer
menu item ~ page 20.
• To access additiona l content, turn the thu mb-
wheel @~
page 20, fig. 8. ""

a:,
a:,
...... N r--. N .-< 0 0 ::, a:,
You can identify which on-board computer is cur ­
r e ntly being shown in the display based on th e
small
O or fl .
The o n-board computer 0 ¢ fig . 9 is a short-term
memo ry .
It collects driving information from the
time the ignition is switch ed on until it is sw itch ­
ed off. If you continue driving within two hours
after switching the ignition off, the new values
are included when calculating the current trip in­
formation .
Unlike the short-term memory , the long-term
memory (on-board computer
fl ) is not erased
automatically. You can select the time period for
evaluating trip information yourself .
You can call up the following information consec­
utively in on -board computer
O or fl :
- Date
- Range
- Travel time
- Average consumption
- Average speed
- Distance
- Current fuel consumption
@ Tips
Information on the efficiency program
¢page 21.
Efficiency program
Overview
Applies to: vehicles with efficiency program
Fig. 10 Instrument cluster: e ffi ciency program
Driver in forma tion system
Operating with the windshield wiper lever*
.,. Press the !RESE T I button @¢page 19, fig. 7
repeatedly until the efficiency program appears
in the display .
Operating with the multifunction steering
wheel*
.,. Open car f unctions and select the Efficiency
program
menu item ¢ page 20.
The eff iciency program can help you to use less
fuel.
It eva luates dr iving information in reference
to fuel consumption and shows other equipment
influencing consumption
¢ page 21. Fuel econ­
omy messages ¢
page 22 provide tips for effi­
c ient driving.
The efficiency program uses distance and con­
sumption data from trip computer
1. If the data
are deleted in the efficiency program
¢
page 19/ ¢ page 20, those values are also reset
in trip computer
1.
Other equipment
Applies to : vehicles with efficiency program
Fig. 11 Instrume nt cluster: e nerg y consumers
Requirement: The efficiency program ii must be
open
¢ page 21 .
.,. Operating with the windshield wiper lever*:
press the button@¢
page 19, fig. 7 repeated­
ly, until the other equipment affecting con­
sumption appears in the instrument cluster dis­
play
¢ fig . 11 .
.,. Operating w ith the multifunction steering
wheel* : keep turning the thumbwheel@
¢
page 20, fig . 8 unti l the other equipment af-
fecting consumption appears in the display. .,.
21

Driver information system
Other equipment that is currently affecting fuel
consumption is listed in the efficiency program .
The display shows up to three other items of
equ ipment @. The equipment using the most
power is listed first. If more than three items us­
ing power are switched on, the equipment that is
currently us ing the most power is displayed.
A gauge @also shows the current total con­
sumption of all other consumers.
Fuel economy messages
Applies to: vehicles with efficiency program
Fig . 12 Instrument cluster: example of economy t ip
Fue l economy messages are d isplayed when fue l
consumption is increased by certain conditions. If
you follow these economy tips, you can reduce
your vehicle's fuel consumption. The messages
appear automatically and are only displayed in
the efficiency program . The fuel economy mes­
sages turn off automatically after a certai n pe ri­
od of time.
• To turn an economy tip off immediately after it
appears, press any button on the windshield
wipe r lever*/multifunction steering wheel*.
(D Tips
-Once you have turned an economy tip off, it
will only appea r again after you turn the ig­
nition on again.
- The economy tips are not displayed in every
instanc e, but rather in intervals over a peri­
od of time .
22