2016 NISSAN NOTE lock

DOOR LOCK ACTUATORDLK-245
< DTC/CIRCUIT DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Is the inspection result normal?
YES >> Replace rear door lock actuator LH. Refer to DLK-299, "DOOR LOCK : Removal and Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator LH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between rear door lock actuator LH harness connector and ground.
Is the inspection result normal?
YES >> Check for internal short of each door lock actuator.
NO >> Replace BCM. Refer to BCS-137, "
Removal and Installation".
REAR RH
REAR RH : DescriptionINFOID:0000000012430206
Locks/unlocks the door with the signal from BCM.
REAR RH : Component Function CheckINFOID:0000000012430207
1.CHECK FUNCTION
1. Perform “DOOR LOCK” in “Active Test” using CONSULT.
2. Touch “ALL LOCK” or “ALL UNLOCK” to check that it works normally.
Is the inspection result normal?
(+)
(–) Condition Vo l ta g e
(Approx.)
Rear door lock actuator LH
Connector Terminal
D205 1
Ground Door lock and unlock switch Lock
Battery voltage
2 Unlock
BCMRear door lock actuator LH
Continuity
Connector TerminalConnector Terminal
M19 54
D205 1
Ye s
53 2
BCM GroundContinuity
Connector Terminal
M19 54
No
53
(+)
(–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M19 54
Ground Door lock and unlock switch Lock
Battery voltage
53 Unlock
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-246
< DTC/CIRCUIT DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK ACTUATOR
YES >> Door lock actuator is OK.
NO >> Refer to
DLK-246, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000012430208
Regarding Wiring Diagram information, refer to DLK-206, "Wiring Diagram".
1.CHECK DOOR LOCK ACTUATOR INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect rear door lock actuator RH connector.
3. Check voltage between rear door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES >> Replace rear door lock actuator RH. Refer to DLK-299, "DOOR LOCK : Removal and Installation".
NO >> GO TO 2.
2.CHECK DOOR LOCK ACTUATOR CIRCUIT
1. Disconnect BCM connector and all door lock actuator connectors.
2. Check continuity between BCM harness connector and rear door lock actuator RH harness connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between rear door lock actuator RH harness connector and ground.
Is the inspection result normal?
YES >> Check for internal short of each door lock actuator.
NO >> Replace BCM. Refer to BCS-137, "
Removal and Installation".
(+)
(–) Condition Vo l ta g e
(Approx.)
Rear door lock actuator RH
Connector Terminal
D305 2
Ground Door lock and unlock switch Lock
Battery voltage
1 Unlock
BCMRear door lock actuator RH
Continuity
Connector TerminalConnector Terminal
M19 54
D305 2
Ye s
53 1
BCM GroundContinuity
Connector Terminal
M19 54
No
53
(+)
(–) Condition Vo l ta g e
(Approx.)
BCM
Connector Terminal
M19 54
Ground Door lock and unlock switch Lock
Battery voltage
53 Unlock
Revision: August 2015 2016 Versa Note

cardiagn.com

REMOTE KEYLESS ENTRY RECEIVERDLK-247
< DTC/CIRCUIT DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
REMOTE KEYLESS ENTRY RECEIVER
DescriptionINFOID:0000000012430209
Receives keyfob operation and transmits to BCM.
Component Function CheckINFOID:0000000012430210
1.CHECK FUNCTION
With CONSULT
Check remote keyless entry receiver “KEYLESS LOCK”, “KEYLESS UNLOCK”, and “KEYLESS PANIC” in
“Data Monitor”.
Is the inspection result normal?
YES >> Remote keyless entry receiver is OK.
NO >> Refer to DLK-247, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430211
Regarding Wiring Diagram information, refer to DLK-216, "Wiring Diagram".
1.CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between remote keyless entry receiver connector and ground with oscilloscope.
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 2.
Monitor item Condition
KEYLESS LOCK Checks whether value changes from “Off” to “On” when operating keyfob lock button.
KEYLESS UNLOCK Checks whether value changes from “Off” to “On” when operating keyfob unlock button.
KEYLESS PANIC Checks whether value changes from “Off” to “On” when operating keyfob panic button.
Te r m i n a l s
ConditionSignal
(Reference value)
(+)
(–)
Remote keyless entry re-
ceiver connector Te r m i n a l
M23 2 Ground Waiting
(All doors closed)
When signal is received (All doors closed)
PIIB7728J
PIIB7729J
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-250
< DTC/CIRCUIT DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY AND FUNCTION
KEYFOB BATTERY AND FUNCTION
DescriptionINFOID:0000000012430212
The following functions are available when having and carrying the keyfob:
• Door lock/unlock
• Panic mode (horn and head-lamp operation)
Remote control entry function and panic alarm functi
on are available when operating the remote buttons.
Component Function CheckINFOID:0000000012430213
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II
User Guide for additional information.
• Check keyfob relative signal strength.
• Confirm vehicle antenna signal strength.
1.CHECK FUNCTION
With CONSULT
Check remote keyless entry receiver “KEYLESS LOCK”, “KEYLESS UNLOCK”, and “KEYLESS PANIC” in
“Data Monitor”.
Is the inspection result normal?
YES >> Keyfob is OK.
NO >> Refer to DLK-250, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012430214
NOTE:
The Signal Tech II Tool [- (J-50190)] can be used to perform the following functions: Refer to the Signal Tech II
User Guide for additional information.
• Check keyfob relative signal strength.
• Confirm vehicle antenna signal strength.
1.CHECK KEYFOB FUNCTION
Check keyfob function using Signal Tech II Tool [- (J-50190)] or
Remote Keyless Entry Tester [- (J-43241)] (shown).
Does the test pass?
YES >> Keyfob is OK.
NO >> GO TO 2.
2. CHECK KEYFOB COMPONENTS
Monitor item Condition
KEYLESS LOCK Checks whether value changes from “Off” to “On” when operating keyfob lock button.
KEYLESS UNLOCK Checks whether value changes from “Off” to “On” when operating keyfob unlock button.
KEYLESS PANIC Checks whether value changes from “Off” to “On” when operating keyfob panic button.
ALKIA2300ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

POWER DOOR LOCK SYSTEM SYMPTOMSDLK-259
< SYMPTOM DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
SYMPTOM DIAGNOSIS
POWER DOOR LOCK SYSTEM SYMPTOMS
Symptom TableINFOID:0000000012430226
DOOR LOCK/UNLOCK FUNCTION MALFUNCTION
NOTE:
• Before performing the diagnosis in the following table, check “WORK FLOW”. Refer to DLK-225, "
Work
Flow".
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check each symptom.
• If the following symptoms are detec ted, check systems shown in the “Diagnosis/service procedure” column
in this order.
Symptom Diagnosis/service procedure Reference page
Key reminder door function does not operate
properly. 1. Check door switch.
DLK-232
2. Check key switch.DLK-241
3. Check Intermittent Incident. GI-42
Power door lock does not operate with door
lock and unlock switch on main power window
and door lock/unlock switch or power window
and door lock/unlock switch RH.1. Check BCM power supply and ground circuit.
BCS-1292. Check main power window and door lock and unlock switch. DLK-235
3. Check power window and door lock and unlock switch RH.DLK-236
4. Check Intermittent Incident. GI-42
Specific door lock actuator does not operate.1. Check door lock actuator.Front LH
DLK-242
Front RHDLK-243
Rear LHDLK-244
Rear RHDLK-245
2. Check Intermittent Incident. GI-42
Power door locks do not operate with front
door lock key cylinder switch LH.1. Check key cylinder switch.
DLK-239
2. Replace BCM.BCS-137
Vehicle speed sensing auto door LOCK oper-
ation does not operate.1. Ensure automatic door lock/unlock function (lock operation)
is enabled. DLK-196
2. Check combination meter vehicle speed signal. MWI-40
(Type
A)
MWI-95
(Type
B)
3. Check intermittent incident. GI-42
Ignition OFF interlock auto door UNLOCK
function does not operate.1. Ensure automatic door lock/unlock function (unlock opera-
tion) is enabled. DLK-196
2. Check BCM for DTCs.
BCS-115
3. Check intermittent incident. GI-42
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-260
< SYMPTOM DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY SYSTEM SYMPTOMS
REMOTE KEYLESS ENTR
Y SYSTEM SYMPTOMS
Symptom TableINFOID:0000000012430227
REMOTE KEYLESS ENTRY SYSTEM
Symptom Diagnoses/service procedureReference
page
All functions of remote keyless entry system do not
operate. 1. Keyfob battery and function check (use Remote Keyless Entry
Tester [- (J-43241)] or Signal
Tech II Tool [- (J-50190)]).
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning. DLK-250
2. Check BCM and remote keyless entry receiver.
DLK-247
The new ID of keyfob cannot be entered.1. Keyfob battery and function check (use Remote Keyless Entry
Tester [- (J-43241)] or Signal
Tech II Tool [- (J-50190)]).
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning. DLK-250
2. Door switch check.
DLK-232
3. Replace BCM.BCS-137
Door lock or unlock does not function.
(If the power door lock system does not operate
manually, check power door lock system)1. Keyfob battery and function check (use Remote Keyless Entry
Tester [- (J-43241)] or Signal
Tech II Tool [- (J-50190)]).
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning. DLK-250
2. Replace BCM.
BCS-137
Hazard and horn reminder does not activate properly
when pressing lock or unlock button of keyfob.1. Check hazard and horn reminder mode with CONSULT
NOTE:
Hazard and horn reminder mode can be changed.
First check the hazard and horn reminder mode setting.
DLK-199
2. Door switch check
DLK-232
3. Replace BCM.BCS-137
Hazard reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Horn reminder OK)1. Check hazard reminder mode with CONSULT
NOTE:
Hazard reminder mode can be changed.
First check the hazard reminder mode setting.
DLK-199
2. Check hazard function with hazard switch
—
3. Replace BCM. BCS-137
Horn reminder does not activate properly when
pressing lock or unlock button of keyfob.
(Hazard reminder OK)1. Check horn reminde
r mode with CONSULT
NOTE:
Horn reminder mode can be changed.
First check the horn reminder mode setting. DLK-199
2. Check horn function with horn switch
—
3. IPDM E/R operation check PCS-10
4. Replace BCM.BCS-137
Room lamp illumination does not operate properly.1. Room lamp operation check
INL-72. Door switch checkDLK-232
3. Replace BCM.BCS-137
Panic alarm (horn and headlamp) does not activate
when panic alarm button is continuously pressed.1. Keyfob battery and function check (use Remote Keyless Entry
Tester [- (J-43241)] or Signal
Tech II Tool [- (J-50190)]).
NOTE:
If the result of keyfob function check is OK, keyfob is not malfunc-
tioning. DLK-250
2. Replace BCM.
BCS-137
Revision: August 2015 2016 Versa Note

cardiagn.com

REMOTE KEYLESS ENTRY SYSTEM SYMPTOMSDLK-261
< SYMPTOM DIAGNOSIS > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
Auto door lock operation does not activate properly.
(All other remote keyless entry functions OK.) 1. Check auto door lock operation mode with CONSULT
NOTE:
Auto door lock operation mode can be changed.
First check the auto door lock operation mode setting.
DLK-196
2. Replace BCM.
BCS-137
SymptomDiagnoses/service procedureReference
page
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-262
< SYMPTOM DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
SQUEAK AND RATTLE TROUBLE DIAGNOSES
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Work FlowINFOID:0000000012430228
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diag-
nostic Worksheet during the interview to document the facts and conditions when the noise occurs and any
customer's comments; refer to
DLK-266, "
Diagnostic Worksheet". This information is necessary to duplicate
the conditions that exist when the noise occurs.
• The customer may not be able to provide a detailed description or the location of the noise. Attempt to obtain all the facts and conditions that exist w hen the noise occurs (or does not occur).
• If there is more than one noise in the vehicle, be sure to diagnose and repair the noise that the customer is
concerned about. This can be accomplished by test driving the vehicle with the customer.
• After identifying the type of noise, isolate the noise in terms of its characteristics. The noise characteristics
are provided so the customer, service adviser and technician are all speaking the same language when
defining the noise.
• Squeak —(Like tennis shoes on a clean floor)
Squeak characteristics include the light contact/fast movement/brought on by road conditions/hard surfaces
= higher pitch noise/softer surfaces = lower pitch noises/edge to surface = chirping.
• Creak—(Like walking on an old wooden floor)
Creak characteristics include firm contact/slow mo vement/twisting with a rotational movement/pitch depen-
dent on materials/often brought on by activity.
• Rattle—(Like shaking a baby rattle)
Rattle characteristics include the fast repeated contac t/vibration or similar movement/loose parts/missing
clip or fastener/incorrect clearance.
• Knock —(Like a knock on a door)
Knock characteristics include hollow sounding/someti mes repeating/often brought on by driver action.
• Tick—(Like a clock second hand) Tick characteristics include gentle contacting of light materials/loose components/can be caused by driver
action or road conditions.
• Thump—(Heavy, muffled knock noise) Thump characteristics include softer k nock/dead sound often brought on by activity.
• Buzz—(Like a bumble bee)
Buzz characteristics include hi gh frequency rattle/firm contact.
• Often the degree of acceptable noise level will vary depending upon the person. A noise that you may judge as acceptable may be very irritating to the customer.
• Weather conditions, especially humidity and temperat ure, may have a great effect on noise level.
DUPLICATE THE NOISE AND TEST DRIVE
If possible, drive the vehicle with the customer until the noise is duplicated. Note any additional information on
the Diagnostic Worksheet regarding the conditions or lo cation of the noise. This information can be used to
duplicate the same conditions when you confirm the repair.
SBT842
Revision: August 2015 2016 Versa Note

cardiagn.com