2016 NISSAN NOTE lock

FUEL FILLER LID OPENERDLK-305
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
FUEL FILLER LID OPENER
Exploded ViewINFOID:0000000012430280
FUEL FILLER LID
FUEL FILLER LID : Re moval and InstallationINFOID:0000000012430281
REMOVAL
1. Remove fuel cap pin (1).
1. Fuel filler lid lock release cable 2. Fuel filler lid lock 3. Fuel filler lid bumper
4. Fuel filler lid spring 5. Fuel filler lidA. Clip
B. Cable protector Pawl
AWKIA2582ZZ
ALKIA3198ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-306
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FUEL FILLER LID OPENER
2. Remove fuel filler lid screws (A) and fuel filler lid (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid
assembly open/close and lock/unlock operation.
FUEL FILLER OPENER CABLE
FUEL FILLER OPENER CABLE : Removal and InstallationINFOID:0000000012430282
REMOVAL
1. Remove hood lock/fuel filler lid lock release handle. Refer to DLK-167, "HOOD LOCK RELEASE HAN-
DLE : Removal and Installation".
2. Disconnect fuel filler lid opener cable (2) from hood lock/fuel filler lid lock release handle (1).
3. Remove dash side finisher (LH). Refer to INT-24, "
DASH SIDE FINISHER : Removal and Installation".
4. Remove center pillar lower finisher (LH). Refer to INT-25, "
CENTER PILLAR LOWER FINISHER :
Removal and Installation".
5. Remove luggage side lower finisher (LH). Refer to INT-34, "
LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
6. Disconnect fuel filler lid opener cable (1) by pulling downward and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler li d assembly open/close, lock/unlock operation.
FUEL FILLER LID LOCK
ALKIA3199ZZ
JMKIA7999ZZ
JMKIA8139ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

FUEL FILLER LID OPENERDLK-307
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
FUEL FILLER LID LOCK : Removal and InstallationINFOID:0000000012430283
REMOVAL
1. Fully open fuel filler lid.
2. Remove luggage side lower finisher (LH). Refer to INT-34, "
LUGGAGE SIDE LOWER FINISHER :
Removal and Installation".
3. Disconnect the harness connector from the fuel filler lid lock assemby.
4. Release pawls (A) and remove fuel filler lid lock assembly (1). CAUTION:
Be careful not to damage gasket (2) when removing.
5. Disconnect fuel filler lid opener cable (1) by pulling downward and then sliding cable end to the side to remove from fuel filler
lid lock assembly (2).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.
JMKIA8138ZZ
JMKIA8139ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-310
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
KEYFOB BATTERY
KEYFOB BATTERY
Removal and InstallationINFOID:0000000012430286
REPLACEMENT
1. Remove screw from the rear of keyfob.
2. Place the key with the lower case facing up. Use a suitable tool wrapped with tape between upper case
and lower case and separate the lower case from the upper case.
CAUTION:
• Do not touch the circuit board or battery termi nal. Doing so could cause the keyfob to malfunc-
tion
• The keyfob is water-resistant. However, if it does get wet, immediately wipe it dry.
3. When replacing the circuit board assembly, remove circuit board assembly from the upper case.
[Circuit board assembly: Switch rubber + Board surface]
CAUTION:
Do not touch the printed circuits directly.
4. Remove the battery from the lower case and replace it.
CAUTION:
When replacing battery, keep dirt, grease, and other foreign materials off the electrode contact
area.
5. After replacement, fit the lower and upper cases together and tighten with the screw. CAUTION:
After replacing the battery, Be sure to check that door locking operates normally using the keyfob.
Refer to DLK-247, "
ComponentFunctionCheck".
Battery replacement : Coin-type lithium battery
(CR1620)
Revision: August 2015 2016 Versa Note

cardiagn.com

STEERING LOCK UNITDLK-311
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
STEERING LOCK UNIT
Exploded ViewINFOID:0000000012828149
NOTE:
Steering lock unit and key cylinder are serviced as an a ssembly. Ignition switch is available separately.
Removal and Installation - Steering lock unitINFOID:0000000012828150
REMOVAL
1. Disconnect battery cables. Refer to PG-70, "Removal and Installation (Battery)".
2. Remove combination switch. Refer to BCS-138, "
Removal and Installation".
3. Remove cluster lid A. Refer to IP-21, "
Removal and Installation".
4. Disconnect the harness connector from the spiral cable.
5. Disconnect the harness connector from the ignition switch.
ALKIA4124ZZ
1. Steering lock bracket 2. Steering column 3. Ignition switch
4. Steering lock unit 5. NATS antenna amp. A. Tamper resistant self-shear type screw
B. Key cylinder Front
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-312
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
STEERING LOCK UNIT
6. Disconnect the harness connector from the key switch.
7. For models with CVT but without intelligent key system,
perform the following steps to separate key inter-
lock cable from steering lock unit:
a. Lift lock plate (A) in the direction of the arrow ( C) and remove in the direction of the arrow ( D).
b. Disconnect the key interlock cable from the steering lock unit.
8. Using suitable tool, remove tamper resistant self-shear type screw. CAUTION:
Do not reuse screw. Replace with new tamper resistant self-shear type screw.
9. Remove steering lock bracket and steering lock unit.
10. Remove NATS antenna amp. (if necessary). Refer to SEC-159, "
Removal and Installation".
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse screw. Replace with new tamper resistant self-shear type screw.
• Tighten tamper resistant self-shear type screw until head breaks off.
• Adjust the neutral position of the steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
• For initialization and registration of mechanical keys, refer to CONSULT Immobilizer mode and follow the on-
screen instructions.
Removal and Installation - Ignition switchINFOID:0000000012828152
REMOVAL
1. Remove steering column cover. Refer to IP-17, "Removal and Installation".
2. Disconnect ignition switch harness connector.
3. Remove ignition switch screws and ignition switch.
INSTALLATION
Installation is in the reverse order of removal.
Adjust the neutral position of t he steering angle sensor. Refer to BRC-55, "
ADJUSTMENT OF STEERING
ANGLE SENSOR NEUTRAL POSITION : Description".
(1) :Key interlock cable
(B) :Steering lock unit
JSDIA1798ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-2
Exploded View ........................................................48
Removal and Installation ........................................48
TIMING CHAIN ............................................... ...51
Exploded View ..................................................... ...51
Removal and Installation ........................................51
CAMSHAFT .......................................................60
Exploded View ..................................................... ...60
Removal and Installation ........................................60
Inspection ...............................................................68
OIL SEAL ...........................................................73
VALVE OIL SEAL .................................................. ...73
VALVE OIL SEAL : Removal and Installation .........73
FRONT OIL SEAL .................................................. ...74
FRONT OIL SEAL : Removal and Installation ........74
REAR OIL SEAL .................................................... ...74
REAR OIL SEAL : Removal and Installation ..........74
CYLINDER HEAD ........................................... ...76
Exploded View ..................................................... ...76
Removal and Installation ........................................76
Exploded View ........................................................78
Disassembly and Assembly ....................................78
Inspection ...............................................................80
UNIT REMOVAL AND INSTALLATION .....86
ENGINE ASSEMBLY ...................................... ...86
Exploded View ..................................................... ...86
Removal and Installation ........................................87
UNIT DISASSEMBLY AND ASSEMBLY ...91
ENGINE UNIT ....................................................91
Setting .................................................................. ...91
Disassembly ............................................................92
Assembly ................................................................92
CYLINDER BLOCK ...........................................93
Exploded View ........................................................93
Disassembly and Assembly ....................................94
Inspection ..............................................................102
HOW TO SELECT PISTON AND BEARING ...111
Description ........................................................... .111
Connecting Rod Bearing .......................................111
Main Bearing ........................................................113
SERVICE DATA AND SPECIFICATIONS
(SDS) ........ .................................................
116
SERVICE DATA AND SPECIFICATIONS
(SDS) .............................................................. ..
116
General Specification ........................................... .116
Drive Belt ..............................................................116
Spark Plug ............................................................117
Exhaust Manifold ..................................................117
Camshaft ...............................................................117
Cylinder head ........................................................119
Cylinder Block .......................................................121
Main Bearing .........................................................124
Connecting Rod Bearing .......................................125
Revision: August 2015 2016 Versa Note

cardiagn.com

EM-4
< PRECAUTION >[HR16DE]
PRECAUTIONS
• Dowel pins are used for several parts alignment. When replacing and reassembling parts with dowel pins,
check that dowel pins are installed in the original position.
• Cover openings of engine system with a tape or equival ent, if necessary, to seal out foreign materials.
• Mark and arrange disassembly parts in an organi zed way for easy troubleshooting and reassembly.
• When loosening nuts and bolts, start with the one furthest outside, then the one diagonally opposite, and so on. If the order of loosening is specified, do exactl y as specified. Power tools may be used in the step.
Inspection, Repair and ReplacementINFOID:0000000012431684
Before repairing or replacing, thoroughly inspect parts. Inspect new replacement parts in the same way, and
replace if necessary.
Assembly and InstallationINFOID:0000000012431685
• Use torque wrench to tighten bolts or nuts to specification.
• Tighten nuts and bolts in order exactly as specified in the procedure. If a tightening order or procedure is not
specified, tighten nuts and bolts equally in several differ ent steps. Start with the nuts or bolts in the center
and then tighten diagonally starting with the inside and moving to the outside in a spiral pattern.
• Replace with new gasket, packing, oil seal or O-ring.
• Thoroughly wash, clean, and air-blow each part. Carefully check engine oil or engine coolant passages for restrictions and blockages.
• Avoid damaging sliding or mating surfaces. Before assembling, completely remove foreign materials such as cloth lint or dust, and oil the sliding surfaces.
• After refilling engine coolant, bleed the air from the cooling system.
• After repairing, start the engine and increase engine s peed to check for engine coolant leaks, fuel leaks,
engine oil leaks, and exhaust gas leaks.
Parts Requiring Angle TighteningINFOID:0000000012431686
• For the final tightening of the following engine parts use Tool:
- Camshaft sprocket (INT) bolt
- Cylinder head bolts
- Main bearing cap bolts
- Connecting rod cap bolts
- Crankshaft pulley bolt (Note an angle wrench is required as bolt flange is provided with notches for angle tightening)
• Do not use a torque value for final tightening.
• The torque value for these parts are for a preliminary step.
• Ensure thread and seat surfaces are clean and coated with engine oil.
Precaution for Liquid GasketINFOID:0000000012431687
REMOVAL OF LIQUID GASKET SEALING
• After removing the bolts and nuts, separate the mating surface and remove the liquid gasket using Tool (A).
CAUTION:
Be careful not to damage the mating surfaces.
• In areas where the cutter is difficult to use, use a plastic hammer to lightly tap (1) the cutter where the liquid gasket is applied. Use a
plastic hammer to slide (2) the cutter by tapping on the side.
CAUTION:
Do not damage the mating surfaces. Tool number : KV10112100 (BT-8653-A)
Tool Number (A) : KV10111100 (J-37228)
AWBIA1249GB
Revision: August 2015
2016 Versa Note

cardiagn.com