2016 NISSAN NOTE tow

SYSTEMBRC-23
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
• Brake force control function at braking hard detects driver ′s brake operations with the pressure sensor,
judges a brake booster ′s maximum brake power function by using information from the vacuum sensor, and
enhances more powerful braking force by controlling brakes of four wheels.
• VDC warning lamp blinks while VDC function is in operat ion and indicates to the driver that the function is in
operation.
• CONSULT can be used to diagnose the system.
• Fail-safe function is adopted. When a malfunction occurs in VDC function, the control is suspended for VDC
function and TCS function. However, ABS function and EBD function operate normally. Refer to BRC-39,
"Fail-safe".
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
OPERATION CHARACTERISTICS
VDC Function That Prevents Oversteer Tendency
• During cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the outer
side of turn. Momentum is generated directing the vehicle toward the outer side of the turn. Oversteer is pre-
vented.
• Changing driving lane on a slippery road, when there may be a tendency to oversteer, engine output is con-
trolled as well as brake force (brake fluid pr essure) of 4 wheels. Oversteer tendency decreases.
Component Signal description
ECM Transmits the following signals to ABS actuator an
d electric unit (control unit) via CAN commu-
nication:
• Acceleration pedal position signal
• Engine speed signal
• Target throttle position signal
TCM Transmits the current gear positi
on signal to ABS actuator and electric unit (control unit) via
CAN communication.
Steering angle sensor Transmits the steering an
gle sensor signal to ABS actuator an d electric unit (control unit) via
CAN communication.
Combination meter Transmits the following signals to ABS actuator an
d electric unit (control unit) via CAN commu-
nication:
• Brake fluid level switch signal
• parking brake switch signal
Receives the following signals from ABS actuator and electric unit (control unit) via CAN com-
munication:
• VDC OFF indicator lamp signal
• SLIP indicator lamp signal
ALFIA0339GB
ALFIA0340GB
Revision: August 2015 2016 Versa Note

cardiagn.com

BRC-24
< SYSTEM DESCRIPTION >[VDC/TCS/ABS]
SYSTEM
VDC Function That Prevents Understeer Tendency
• During cornering, brake force (brake fluid pressure) is applied on front wheel and rear wheel on the inner
side of turn. Momentum is generated directing the vehicle toward the inner side of the turn. Understeer is
prevented.
• Applying brakes during cornering on a slippery road, when there may be a tendency to understeer, engine output is controlled as well as brake force (bra ke fluid pressure) of 4 wheels. Understeer tendency
decreases.
VDC/TCS/ABS : TCS FunctionINFOID:0000000012430838
SYSTEM DIAGRAM
SYSTEM DESCRIPTION
JPFIC0137GB
ALFIA0341GB
AWFIA0807GB
Revision: August 2015 2016 Versa Note

cardiagn.com

B RC-106
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1154 TRANSMISSION RANGE SWITCH
C1154 TRANSMISSION RANGE SWITCH
DTC DescriptionINFOID:0000000012430885
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1154” detected?
YES-1 >> “C1154” is displayed as “CRNT”: Proceed to BRC-106, "Diagnosis Procedure".
YES-2 >> “C1154” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430886
CAUTION:
“C1154” may be detected when goin g up a slope, being towed with ignition switch ON and the shift
selector in a position other than R position. This is not a shift position error. The system returns to
normal once the vehicle is stopped, parked on level ground and the engine is started.
1.CHECK CVT SYSTEM
With CONSULT
Perform “Self Diagnostic Resu lt” of “TRANSMISSION”.
Is DTC detected?
YES >> Check the DTC. Refer to TM-110, "DTC Index".
NO >> GO TO 2.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1154 PNP POSI SIG
(PNP position signal) When a malfunction is detected in TCM system.
PAST DTC
CRNT DTC
• Harness or connector
• Transmission range switch • Harness or connector
• ABS actuator and electric unit (control unit)
•TCM
• Transmission range switch
Revision: August 2015
2016 Versa Note

cardiagn.com

FRONT DOOR LOCKDLK-171
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
7. While pulling outside handle (1), slide toward rear of vehicle.
8. Disconnect the harness connectors from the outside handle and remove.
9. Remove front gasket and rear gasket.
10. Slide outside handle bracket toward rear of vehicle to remove. : Front
11. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-174
< REMOVAL AND INSTALLATION >[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR LOCK
6. Release inside handle cable (3) and lock cable (2) from inside
handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are pr operly engaged to inside handle.
• After installation, check door op en/close, lock/unlock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430130
REMOVAL
1. Remove inside handle. Refer to DLK-173, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR DOOR LOCKDLK-175
< REMOVAL AND INSTALLATION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
5. Remove front gasket and rear gasket.
6. Slide outside handle bracket toward rear of vehicle to remove. : Front
7. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, check door open/close, lock/un lock operation.
• Check door lock cable is properly engaged with outside handle bracket.
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

DLK-298
< REMOVAL AND INSTALLATION >[WITHOUT INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
7. While pulling outside handle (1), slide toward rear of vehicle to
remove.
8. Remove front gasket and rear gasket.
9. Slide outside handle bracket toward rear of vehicle to remove. : Front
10. Disconnect outside handle cable (1) from outside handle bracket (2) as shown.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are prope rly engaged with outside handle bracket.
• After installation, check door op en/close, and lock/unlock operation.
JMKIA0524ZZ
JMKIA5890ZZ
JMKIA5891ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com

REAR DOOR LOCKDLK-301
< REMOVAL AND INSTALLATION > [WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
6. Release inside handle cable (3) and lock cable (2) from inside handle (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Check that door lock cables are properly engaged to inside handle.
• After installation, check door open/close, lock/un lock operation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Removal and InstallationINFOID:0000000012430276
REMOVAL
1. Remove inside handle. Refer to DLK-300, "INSIDE HANDLE : Removal and Installation"
2. Remove door grommet and bolt from grommet hole.
3. While pulling outside handle, remove outside handle escutch-
eon.
4. While pulling outside handle (1), slide towards rear of vehicle to remove.
JMKIA5885ZZ
JMKIA1467ZZ
JMKIA5342ZZ
JMKIA0524ZZ
Revision: August 2015 2016 Versa Note

cardiagn.com