2016 AUDI S8 Owners Manual

& WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect
may be delayed due to moisture on the
brake rotors or ice in the winter . The brakes
must be dried first with a few careful brake
applications.
{[) Note
-If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding
function.
- To prevent paint damage, do not wash the
vehicle in direct sunlight.
-
Care and cleaning
-To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or similar items.
- Matte finish painted vehicle components:
- To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
- Never use car wash cycles that apply pro­
tective wax. It can destroy the matte fin­
ish effect.
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the vehicle in facilities specially de­
signed for that purpose. This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following table. The in­
formation contained there is simply recommen­
dations. For questions or for components that are not
listed, refer to an authorized Audi dealer
or a qualified workshop. Also follow the informa­
tion found in
~ ,&. .
Cleaning exterior
Component Situation Solution
Wiper blades
Dirty ~ page 55, Cleaning windshield wiper blades
Headlights/ Dirty Soft sponge with a mild soap solution a>
tail lights
Sensors/
Dirty Sensors: soft cloth with a solvent-free cleaning product
camera lenses Camera lenses: soft cloth with an alcohol-free cleaning sol-
ution
Snow/ice Hand
brush/solvent-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
Exhaust tail Road salt
Water, cleaning solution suitable for stainless steel, if nee-
pipes essary
207

Care and cleaning Component Situation Solution
Decorative parts/
Dirty Mild soap solutiona>, a cleaning solution suitable for stain-
trim less steel, if necessary
Paint Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint
¢page 277
Spilled fuel Rinse with water immediately
Rust film Rust film remover, then protect
with hard wax; for ques-
tions, refer to an authorized Audi dealer or a qualified
workshop
Corros ion Have it removed by an authorized Aud i dea ler or a qua lified
wo rkshop
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean pa int
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in-Dampen with water immediately and remove w ith a micro-
sects, bird droppings, fiber cloth
tree sap and road salt
grease-based con- Remove immediately with a m ild soap solutiona> and a soft
taminants such as cloth
cosmetics or sunblock
Carbon parts Dirty Clean the same way as painted parts¢ page 206, Car
washes
a l Mild soap so lution: maxim um two tablespoo ns neu tra l soap in 1 quar t Cl lite r) of water
Cleaning interior
Component Situation Solution
Windows
Dirty Glass cleaner, then wipe dry
Decorative parts/ Dirty Mild soap so lutiona>
trim
Plastic parts
Dirty Damp cloth
Heavily soiled Mild soap solutiona>, solvent-free p lastic clean ing solution,
if necessary
Displays Dirty Soft cloth with LCD cleaner
Controls Dirty Soft brush, then a soft cloth with a m ild soap solutiona >
Safety belts Dirty Mild
soap solutiona>, allow to dry before letting them re-
tract
208
...

Care and cleaning
Component S ituation Solution
Tex tiles,
Stains adhering to Vacuum cleaner
Vin yl, the surface
A lcan tara Water-based stains Absorbent cloth and mild soap
solutional
such as coffee, tea,
blood, etc.
Oil-based stains such Apply a m ild soap solutional, blot away the d issolved oil or
as o il, make-up, etc. dye, treat afterward with water, if necessary
Special stains such as Special stain remover, blot with
absorbent material, treat
ballpoint pen, nail afterward with mild soap solutional, if necessary
polish, latex paint,
shoe polish, etc .
Natural le athe r Fresh stains Cotton cloth
with a mild soap solutiona l
Water -based stains Fresh stains : absorbent cloth
such as coffee, tea, Dried stains : stain remover suitable for leather
blood, etc.
Oi l-based stains such Fresh stains: absorbent cloth and stain remover suitable
as oi l, make-up, etc. for leather
dried stains: Oil cleaning spray
Special stains such as S tain remover suitable fo r leather
ballpoint pen, nail
polish, latex paint,
shoe po lish , etc.
Ca re Regularly apply cond ition ing cream that p rotects from
light and penetrates into the materia l. Use specially-co l-
ored cond itioning cream, if necessary.
Cooler Dust and dirt Clea n the ventilation openings in the luggage com part-
ment
Dirty Lukewarm water, mild soap solutional if necessary, then
dry
Defrosting Empty the refrigerator, switch it off and let it thaw with
the doo r open, t hen dry
Car bon p art s Dirty Clean the same way as plastic parts
a) M ild soap solut io n: max imu m two tablespoons neutral soap in 1 q uart (I liter) of water
A WARNING
The windshie ld may not be treated with wa­
ter-repelling windshield coating agents. Un­
favorable cond itions such as wetness, dar k­
ness, o r low sun can resul t in increased glare.
Wiper blade chatter is also possib le.
- Headlights /tail light s
-
-Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcoho l, because they could cause
cracks to form.
-Whe els
- Never use any pa int polish or other abra-
sive mate rials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately. .,..
209

Care and cleaning
-Sensors/camera lenses
- Never use warm or hot water to remove
snow or ice from the camera lens. This
could cause the lens to crack .
- Never use abrasive cleaning materials or
alcohol to clean the camera lens . This
could cause scratches and cracks .
-Windows
- Remove snow and ice on windows and ex-
terior mirrors with a plastic scraper. To
avoid scratches, move the scraper only in
one direction and not back and forth.
- Never remove snow or ice from windows
and mirrors using warm or hot water be­
cause this could cause cracks to form.
- To avoid damage to the rear window de­
fogger, do not apply any stickers on the heating wires on the inside of the window.
- Decorative part .s/trim
- Never use chrome care or cleaning prod-
ucts.
-Paint
-To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol­
ishing or waxing.
- To prevent paint damage, do not polish or
wax the vehicle in direct sunlight.
- To reduce the risk of paint damage, do not
polish away rust film .
- Remove cosmetics and sunblock immedi­
ately. Otherwise, the paint could be dam­
aged.
-Trim
- To reduce the risk of damage, do not treat
the trim around the panorama sunroof
with paint polish.
- Decorative decals
-To reduce the risk of damage, do not use
any rough powder or abrasive cleaning
products .
- To reduce the risk of damage, do not pol­
ish decorative parts that have a matte fin­
ish .
-Displays
- To avoid scratches, do not use dry cleaning
methods on displays.
-Controls
210
- Make sure that no fluids enter the con­
trols, because this could cause damage.
- Safety belts
- Do not remove the safety belts to clean
them .
- Never clean safety belts or their compo­
nents chemically or with corrosive fluids
or solvents and never allow sharp objects
to come into contact with the safety belts.
This could cause damage to the belt web­ bing .
- If there is damage to the webbing, the
connections , the retractors or the buckles,
have them replaced by an authorized Audi
dealer or a qualified workshop.
- Textiles/Vinyl/ Alcantara
- Never treat Vinyl/ Alcantara with leather
care products, solvents, floor polish, shoe
polish, stain remover or similar products .
- To avoid damage, have stubborn stains re­
moved by an authorized Audi dealer or a
qualified workshop.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
-Do not turn on the seat heating* to dry the
seat.
- Objects with sharp edges such as zippers,
rivets on clothing or belts can cause dam­
age to the surface.
- Open hook and loop fasteners , for exam­
ple on clothing, can damage seat covers .
Make sure hook and loop fasteners are
closed .
-Natural leather
- Never treat leather with solvents, floor
polish, shoe polish, stain remover or simi­
lar products.
- Objects with sharp edges such as zippers,
rivets on clothing or belts can cause dam­
age to the surface.
- Never use steam cleaners, brushes , hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the
seat .
- To help prevent the leather from fading,
do not leave the vehicle in direct sunlight
for long periods of time. If leaving the

vehicle parked for long periods of time,
you should cover the leather to protect it
from direct sunlight .
-Cooler
-Do not try to speed up the defrosting
process by applying heat .
- To help prevent health r isks o r damage to
the cooler , do not use any abrasive clean­
ers , solvents, wax o r strongly scented or
agg ressive cleaning products .
- Do not clean the cooler with rough clean ­
ing tools s uch as steel wool.
- Insects are easier to remove from paint that
has been fresh ly waxed .
- Regular waxing can prevent rust film from
form ing .
Ca re and cleaning
211

Fuel and Refueling
Fuel and Refueling
Gasoline
Fuel supply
Applies to: vehicles with gaso line engine
Using the right fuel helps keep the environment
clean and prevents engine damage.
Fuel recommendation
The fuel recommended for your vehicle is unlead­
ed premium
grade gasoline . Audi recommends
using TOP TIER Detergent Gasoline with a mini­
mum octane rating of 91 AKI (95 RON). For more
information on TOP TIER Detergent Gasoline,
p lea se go to the offic ial website
(www.toptiergas .com).
The recommended gasoline octane rating for
your engine can also be found on a label located
on the ins ide of the fuel filler flap . This rating
may be specified as AKI or RON.
Your vehicle may also be operated using unlead­
ed regular gasoline with a minimum octane rat­
ing of 87 AKl/91 RON . However, using 87 AKI/91
RON octane fuel wil l slightly reduce engine per­
formance.
Use unleaded gasoline only. Unleaded gasoline
is availab le throughout the USA, Canada, and in
most European countries . We recommend that
you do not take your vehicle to areas or countries
where un leaded gaso line may not be available.
For more information on refueling your vehicle,
see
¢ page 214.
Octane rating
Octane rating indicates a gasoline's ability to re­
sist engine damaging "knock" caused by prema­
ture ignit ion and detonation . Therefore, buying
the correct grade of gasoline is very important to
he lp prevent possible engine damage and a loss
of eng ine performance.
Gasoline most commonly used in the United
States and Canada has the following octane rat­
i n gs that can usually be found on the filler pump:
- Premium Grade: 91 - 96 AKI
212
- Regular Grade: 87 - 90 AKI
Explanation of the abbreviations:
AKI = Anti Knock Index = (R +M)/2 = (RON +MON)/
2
RON = Research Octane Number
MON= Motor Octane Number.
{[) Note
-Do not use any fuel with octane ratings low­
er than 87 AKI or 91 RON otherwise expen­
sive engine damage wi ll occur .
- Do
not use leaded gasoline. The use of lead­
ed gasoline will severely damage your vehi­
cle's catalytic converter and its ability to
control exhaust emissions .
Blended gasoline
Applies to: vehicles with gasoline engine
Use of gasoline containing alcohol or MTBE
(methyl tertiary butyl ether)
You may use unleaded gasoline blended with al­
cohol or MTBE (commonly referred to as oxygen ­
ates) if the blended mixture meets the following
criteria:
Blend of gasoline methanol (wood alcohol or
methyl alcohol)
-Anti -knock index must be 87 AKI or h igher.
- Blend must contain no more than 3% metha-
nol.
- Blend must contain more than 2% co-solvents.
Blend of gasoline and ethanol (grain alcohol or
ethyl alcohol)
- Anti-knock index must be 87 AKI or h igher .
- Blend must not contain more than 15% etha-
nol.
Blend of gasoline and MTBE
-Anti-knock index must be 87 AK I or higher .
- Blend must contain not mo re than 1S% MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform es­
pecially well for winter or summer dr iv ing . Dur-
i ng seasonal change-over, we suggest that you .,..

fill up at busy gas st ations where the season al
adjustment is more likely to be made in time .
(D Note
-Me thanol f uels which do not mee t these re­
quirements may ca use corros ion and dam­
age to plastic and rubber components in the
fuel system .
- Do not use fuels that fai l to meet the speci­
fied criter ia in this chapter.
- If you are unable to determine whether or not a particular fuel blend meets the speci­
ficat ions, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can­
not be identif ied.
- Fuel system damage and performance prob­
lems resulting from the use of fue ls differ­
ent from those specified are not the respon­
s ibility of Audi and are not covered under
the New Veh icle or the Emiss ion Control
System Wa rrant ies.
- If you experience a loss of fue l economy or
driveability and performance prob lems due
to the use of one of these fuel b lends, we
recommend that you switch to unblended
fuel.
Gasoline additives
Applies to: vehicles with gasol ine engine
A majo r concern among many au to manufactur ­
ers is carbon deposit build- up caused by the type
of gasoline yo u use.
A lthough gasoline grades d iffer from one manu­
f a cturer to ano ther, they have cer tain things in
common . A ll gasoline grades contain substances
that can cause deposits to collect on vita l engine
pa rts, such as fue l injectors and intake valves . Al ­
though most gaso line brands include additives to
keep engine and fuel systems clean, they are not
equally effective.
Aud i recommends using TOP TIER Detergent Gas­
oline. For more informat ion on TOP TIER Deter­
gent Gasoline, please go to the official website (www.toptiergas .com) .
Fuel and R efueling
After an extended period o f using inadeq uate
fuels, carbon deposit bui ld-ups can rob your en­
gine o f peak performance.
(D Note
Damage or ma lf u nction due to poo r fue l qual ­
ity is not covered by the A udi New Vehicle
Limited Warranty .
Diesel fuel
Applies to: vehicles with diesel engine
Always use ULSD (Ultra Low Sulfur Diesel) No. 2 .
The ULSD No . 2 meets the ASTM 0975.
Diesel f uel w it h concen tratio ns of b iod iesel h igh­
er than 5 % such as Bl 1, B20 or BlOO are strict ly
prohibited .
Se rvice station fuel p umps are labe led with the
correct f uel i nfo rmat ion for e asy recog nition by
the user.
If the d iesel f ue l pump is no t labeled
ask the station operator what fuel is being dis­
pensed before fil ling up your vehicle .
UL SD No . 2 m ay not be available ou tside the USA
and Canada . Be su re to check befo re t raveling to
other countries .
UL SD No . 2 c an become thic ke r i n ve ry cold tem­
peratures, and this can imp air the engine's s tart ­
ing and running. Depend ing on the sea son, gas
stations provide ULSD No . 2 that flows better in
cold temperatures so that you can continue oper ­
at ing your vehicle as usual.
@ Note
- Your vehicle's diese l engine was designed
sole ly for use with ULSD No . 2 . Therefo re,
neve r use gasoline, heating oil, other fuels
or flow improvers. These contain substances
that will severely damage the fuel system
and the engine . Such damage will not be
cove red by your New Vehicle Limited War-
r a nty.
- If you put a ny amo unt of incorrect fuel in
the fuel tank, do not sta rt the eng ine under
any circumstances. Imme diately contact the
II>-
213

Fuel and Refueling
nearest authorized Audi dealer or author­
ized Audi Service Facility for assistance.
These fuels contain substances that can se­
verely damage the fuel system and the en­
gine if the engine is started.
Refueling
Fuel filler neck
The fuel filler neck is located on the right rear
side panel behind the fuel filler flap.
If the power locking system should fail, you can
still open the flap manual ly -for detailed instruc­
tions see
c;> page 216.
You can find the fuel tank capac ity of your vehicle
In .
The label on the inside of the fuel filler flap tells
you the correct fuel for your vehicle. For more in­
formation about fue l specifications, see
c;> page 212.
Your vehicle fuel tank has an onboard refuelling
vapor recovery system. This feature helps to pre­
vent fuel vapors from escaping from the tank and
pollut ing the environment while you refuel your
veh icle. In order to fill the tank properly while
protecting the environment, please follow this
refueling procedure carefully.
_& WARNING
Under normal operating conditions, never car­
ry additional fuel containers in your car. Gas
canisters and other containers used to trans­
port fuel can be dangerous. Such containers,
full or empty, may leak and could cause a fire
in a collision. If you must transport fuel to
use for you r lawn mower, snow blower, etc.,
be very careful and always observe local and
state laws regarding the use, transportation
and storage of such fuel containers. Make cer­
tain the container meets industry standards
(ANSI/ASTM F852 -86).
(D Note
Never drive your vehicle until the fuel tank is
completely empty. The ir regular supply of
fuel can cause m isfiring. Gasoline could enter
214
the exhaust system and damage the catalytic
converter.
Refuelling
Fig. 188 Right rear vehicle side: Opening the fuel filler flap
Fig. 189 Fuel fille r flap with attached fuel cap
When activating the central locking, the fue l fill­
er flap is automatically unlocked or locked. Re­
fuel the vehicle with the ignition switched
off.
Taking the fuel cap off
.,. Press the left side of the fuel fil ler flap to open
it
c;>fig. 188- arrow- .
.,. Unscrew f uel filler cap counter-clockwise and
hang it on the fuel filler flap¢
fig. 189.
.,. Check the label on the inside of the fuel filler
flap to determine if the vehicle must be fueled
with gasoline or diesel fuel.
Refuelling procedure
.,. Insert the fuel nozz le from the gasoline pump
into the fue l filler neck as far as it will go.
.,. Select a medium refuelling rate so that the
nozzle switches off automatically when the
tank is full.