2014 NISSAN TEANA mirror

TURN SIGNAL LAMP CIRCUITEXL-107
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
EXL
N
O P
6. While the turn signal is operating, check the vo ltage between the rear combination lamp harness connec-
tor and ground.
7. While the turn signal is operating, check t he voltage between the door mirror harness connector and
ground.
Is the inspection result normal?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK TURN SIGNAL LAMP CIRCUIT FOR OPEN
1. Turn the ignition switch OFF.
2. Disconnect BCM harness connector M19 or M20 in question.
3. Check continuity between the BCM harness connecto r M20 and the front combination lamp harness con-
nector.
4. Check continuity between the BCM harness connecto r M19 and the rear combination lamp harness con-
nector.
RH E224 (without front fog lamps)
5Ground
E351 (with front fog lamps)
LH E217
PKID0926E
(+) (− ) Vol tag e
(Approx.)
Connector Terminal
RH B45
3Ground
LH B30
(+) (− ) Vol tag e
(Approx.)
Connector Terminal
RH D107
6Ground
LH D4
PKID0926E
PKID0926E
BCM Front combination lamp Continuity
Connector Terminal Connector Terminal
LH M20 11 7 E 2 1 7
5Yes
RH 105 E224 (without front fog lamps)
E351 (with front fog lamps)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EXL-108
< DTC/CIRCUIT DIAGNOSIS >
TURN SIGNAL LAMP CIRCUIT
5. Check continuity between the BCM harness connector M20 and the door mirror harness connector inquestion.
Is the inspection results normal?
YES >> GO TO 4.
NO >> Repair or replace the harness or connectors.
4.CHECK TURN SIGNAL LAMP SHORT CIRCUIT
1. Check continuity between the BCM harness connector M19 or M20 and ground.
Are the inspection results normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Repair or replace the harness or connectors.
5.CHECK TURN SIGNAL LAMP GROUND CIRCUIT
1. Check continuity between the front combination la mp harness connector or the rear combination lamp
harness connector or the door mirror harness connector in question and ground.
2. Check continuity between the rear co mbination lamp harness connector and ground.
3. Check continuity between the door mirror harness connector and ground.
BCM Rear combination lamp Continuity
Connector Terminal Connector Terminal
LH M19 103 B30
3Yes
RH 92 B45
BCM Door mirror Continuity
Connector Terminal Connector Terminal
LH M20 11 7 D 4
6Yes
RH 105 D107
BCM
GroundContinuity
Connector Terminal
M19 92
No
103
M20 105
11 7
Front combination lamp (− )Continuity
Connector Terminal
LH E217 7 Ground Yes
RH E224 (without front fog lamps)
E351 (with front fog lamps)
Rear combination lamp (− )Continuity
Connector Terminal
LH B30 5 Ground Yes
RH B45
Door mirror (− )Continuity
Connector Terminal
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EXTERIOR LIGHTING SYSTEM SYMPTOMSEXL-115
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K
M A
B
EXL
N
O P
Headlamp is not turned ON/OFF with the lighting
switch AUTO. • Combination switch (lighting
and turn signal switch)
• Harness between the combina- tion switch (lighting and turn sig-
nal switch) and BCM
•BCM
• IPDM E/R Combination switch (lighting and
turn signal switch)
Refer to BCS-79.
• Optical sensor
• Harness between the optical
sensor and BCM
•BCM Optical sensor
Refer to EXL-110
.
Daytime light system does not activate. —Symptom diagnosis
"DAYTIME LIGHT SYSTEM INOP-
ERATIVE"
Refer to EXL-118
.
Front fog lamp is not
turned ON. One side
• Front fog lamp bulb
• Harness between IPDM E/R
and the front fog lamp
• Harness between the front fog lamp and ground
• IPDM E/R Front fog lamp circuit
Refer to EXL-101
.
Both side — Symptom diagnosis
"BOTH SIDE FRONT FOG LAMPS
ARE NOT TURNED ON"
Refer to EXL-121
.
Parking lamp is not turned
ON. One side•Fuse
• Parking lamp bulb
• Harness between IPDM E/R
and the front/rear combination
lamp
• Harness between the front/rear
combination lamp and ground
• IPDM E/R Parking lamp circuit
Refer to EXL-103
.
Both sides — Symptom diagnosis
"PARKING, LICENSE PLATE AND
TAIL LAMPS ARE NOT TURNED
ON"
Refer to EXL-120
.
Turn signal lamp does not
blink. Indicator lamp is nor-
mal.
(The applicable side
performs the high flash-
er activation). • Harness between BCM and
each turn signal lamp
• Turn signal lamp bulb
• Door mirror (if equipped with
turn signals in the door mirrors) Turn signal lamp circuit
Refer to EXL-106
.
Turn signal indicator lamp
does not blink. One side Combination meter —
Both sides
(Always) • Turn signal indicator lamp sig-
nal
• Combination meter
•BCM • Combination meter.
Data monitor "TURN IND"
• BCM (FLASHER) Active test "FLASHER"
Both sides
(Does blink when acti-
vating the hazard warn-
ing lamp with the
ignition switch OFF) • The combination meter power
supply and the ground circuit
• Combination meter Combination meter
Power supply and the ground circuit
Refer to MWI-58
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating. (Turn signal is normal) • Hazard switch
• Harness between the hazard switch and BCM
•BCM Hazard switch
Refer to EXL-112
.
Symptom Possible cause Inspection item
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRROR TURN SIGNAL LAMPEXL-133
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
EXL
N
O P
DOOR MIRROR TURN SIGNAL LAMP
Removal and InstallationINFOID:0000000009463629
REMOVAL
1. Remove the door mirror rear finisher. Refer to MIR-20, "Removal and Installation".
2. Remove the screws (A) and door mirror side turn signal lamp (1).
3. Disconnect the harness connector from the door mirror side turn signal lamp and remove.
INSTALLATION
Installation is in the reverse order of removal.
Bulb ReplacementINFOID:0000000009463630
DOOR MIRROR SIDE TURN SIGNAL LAMP
The door mirror side turn signal lamp bulb is integrated into the door mirror side turn signal lamp and is ser-
viced as an assembly. Refer to EXL-133, "Removal and Installation"
.
ALLIA1142ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EXL-148
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb SpecificationsINFOID:0000000009463650
*: Always check with the Parts Department for the latest parts information.Item Wattage (W)*
Front combination lamp Low beam (halogen) 55
Low beam (xenon) 35
High beam 65
Side marker lamp 5
Turn signal/Park lamp 28/8 (amber)
Door mirror side turn signal lamp (if equipped) LED
Rear combination lamp St op /Ta il la mp
21/5
LED
Turn signal lamp 27
Back-up lamp 16
Side marker lamp 5
Fog lamp (if equipped) 55
Daytime running lamp built-in fog lamp (Canada only) 19
License plate lamp 5
High-mounted stop lamp Parcel shelf mounted LED
Rear spoiler mounted LED
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR SASH MOLDINGEXT-31
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
EXT
N
O P
DOOR SASH MOLDING
Exploded ViewINFOID:0000000009461011
NOTE:
RH side shown; LH side similar.
Removal and Installation INFOID:0000000009461012
FRONT DOOR
Removal
1. Remove the door mirror assembly. Refer to MIR-20, "Removal and Installation".
2. Remove the clip (A) using a suitable tool (B). CAUTION:
Do not reuse the clip (A).
1. Front door 2. Front door weatherstrip 3. Front door sash molding
4. Sash molding inner finisher A. Clip
ALKIA2642ZZ
ALKIA2652ZZ
Revision: November 20132014 Altima NAM

DOOR OUTSIDE MOLDINGEXT-35
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
L
M A
B
EXT
N
O P
DOOR OUTSIDE MOLDING
Exploded ViewINFOID:0000000009461015
Removal and InstallationINFOID:0000000009461016
FRONT DOOR OUTSIDE MOLDING
Removal
1. Remove the door mirror assembly. Refer to MIR-20, "Removal and Installation".
2. Lift and twist from rear side, disconnect clips fr om flange and pull the front door outside molding toward
rear of the vehicle.
Installation
Installation is in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
Lift and twist from rear side, then disconnect clips from flange and pull the rear door outside molding out.
Installation
Installation is in the reverse order of removal.
1. Front door outside molding 2. Rear door outside molding
Clips
ALKIA2684ZZ
Revision: November 20132014 Altima NAM

RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS
GI-21
< HOW TO USE THIS MANUAL >
C
D E
F
G H
I
J
K L
M B
GI
N
O PRECOMMENDED CHEMICAL PRODUCTS AND SEALANTS
Recommended Chemical Products and SealantsINFOID:0000000009462982
Refer to the following chart for help in selecting the appropriate chemical product or sealant.
Product Description Purpose Nissan North America
Part No. (USA) Nissan Canada Part
No. (Canada) Aftermarket Cross-
reference Part Nos.
1 Rear View Mirror Adhe-
sive Used to permanently re-
mount rear view mirrors to
windows. 999MP-AM000P 99998-50505 Permatex 81844
2 Anaerobic Liquid Gas-
ket For metal-to-metal flange
sealing.
Can fill a 0.38 mm (0.015
inch) gap and provide in-
stant sealing for most pow-
ertrain applications. 999MP-AM001P 99998-50503
Permatex 51813 and
51817
3 High Performance
Thread Sealant Provides instant sealing on
any threaded straight or
parallel threaded fitting.
(Thread sealant only, no
locking ability.)
• Do not use on plastic. 999MP-AM002P 999MP-AM002P Permatex 56521
4 Silicone RTV Gasket Maker 999MP-AM003P
(Ultra Grey) 99998-50506
(Ultra Grey) Permatex Ultra Grey
82194;
Three Bond
1207,1215, 1216,
1217F, 1217G and
1217H
Nissan RTV Part No.
999MP-A7007
5 High Temperature,
High Strength Thread
Locking Sealant (Red) Threadlocker 999MP-AM004P 999MP-AM004P Permatex 27200;
Three Bond 1360,
1360N, 1305 N&P,
1307N, 1335,
1335B, 1363B,
1377C, 1386B, D&E
and 1388
Loctite 648
6 Medium Strength
Thread Locking Seal-
ant (Blue) Threadlocker (service tool
removable) 999MP-AM005P 999MP-AM005P Permatex 24200,
24206, 24240,
24283 and 09178;
Three Bond 1322,
1322N, 1324 D&N,
1333D, 1361C,
1364D, 1370C and
1374
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM