2014 NISSAN TEANA brake rotor

< SERVICE DATA AND SPECIFICATIONS (SDS) 2014
QUICK REFERENCE CHART: ALTIMA
Unit: mm (in)
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
CANADA
Unit: mm (in)
*1: Fuel, engine coolant, and lubricants are full. Spare tire, jack, hand tools, and mats are in designated positions.
Brake SpecificationsINFOID:0000000010112414
Unit: mm (in)
Engine
QR25DE VQ35DE
Tire size 215/60R16 215/55R17 235/45R18
Front (Hf) 708 (27.87) 711 (27.99) 714 (28.11)
Rear (Hr) 706 (27.80) 709 (27.91) 711 (27.99)
LEIA0085E
EngineQR25DEVQ35DE
Tire size 215/60R16215/55R17 235/45R18
Front (Hf) 707 (27.83)710 (27.95) 715 (28.15)
Rear (Hr) 706 (27.80)710 (27.95) 712 (28.03)
LEIA0085E
Front brakeCylinder bore diameter
57.2 (2.252)
Pad length × width × thickness 114 × 47 × 10 (4.488 × 1.850 × 0.394)
Rotor outer diameter × thickness 296 × 26 (11.654 × 1.024)
Rear brake Cylinder bore diameter
34.93 (1.375)
Pad length × width × thickness 83 × 33 × 8.5 (3.268 × 1.299 × 0.335)
Rotor outer diameter × thickness 292 × 9 (11.496 × 0.354)
Master cylinder Cylinder bore diameter 25 (0.984)
Control valve Valve model Electric brake force distribution
Brake booster Diaphragm diameter 280 (11)
Recommended brake fluid DOT 3

QUICK REFERENCE CHART: ALTIMA
2014
Brake PedalINFOID:0000000010112415
Unit: mm (in)
Front Disc BrakeINFOID:0000000010112412
Unit: mm (in)
Rear Disc BrakeINFOID:0000000010112413
Unit: mm (in)
ItemStandard
Brake pedal height (H) (from dash lower panel top surface) 181.4 - 191.4 (7.1 - 7.5)
Brake pedal full stroke (S) 135.3 (5.3)
Clearance between stopper bracket (C
1) and threaded end of the stop lamp
switch and ASCD cancel switch (C
2) 0.74 - 1.96 (0.0291 - 0.0772)
AWFIA0913ZZ
Brake padStandard thickness (new) 11.0 (0.433)
Wear limit thickness
2.0 (0.079)
Disc rotor Standard thickness (new)
26.0 (1.024)
Wear limit thickness 24.0 (0.945)
Thickness variation (measured at 8 positions) 0.015 (0.0006)
Maximum runout (with it attached to the vehicle) 0.040 (0.0016)
Brake padStandard thickness (new) 8.5 (0.335)
Wear limit thickness
1.0 (0.039)
Disc rotor Standard thickness (new)
9.0 (0.354)
Wear limit thickness 8.0 (0.315)
Thickness variation (measured at 8 positions) 0.015 (0.0006)
Maximum runout (with it attached to the vehicle) 0.05 (0.0020)

BR-1
BRAKES
C
D E
G H
I
J
K L
M
SECTION BR
A
B
BR
N
O P
CONTENTS
BRAKE SYSTEM
PRECAUTION ................ ...............................3
PRECAUTIONS .............................................. .....3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
3
Precaution for Procedure without Cowl Top Cover ......3
Precaution for Brake System ....................................3
PREPARATION ............................................5
PREPARATION .............................................. .....5
Special Service Tool ........................................... ......5
Commercial Service Tool ..........................................5
SYSTEM DESCRIPTION ..............................6
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING ........................ .....
6
NVH Troubleshooting Chart ................................ ......6
BASIC INSPECTION ....................................7
BRAKE PEDAL .............................................. .....7
Inspection ............................................................ ......7
BRAKE FLUID .....................................................8
Inspection ............................................................ ......8
BRAKE MASTER CYLINDER ........................ .....9
Inspection ............................................................ ......9
On Board Inspection .................................................9
BRAKE BOOSTER ............................................10
Inspection ............................................................ ....10
FRONT DISC BRAKE .................................... ....11
BRAKE PAD .......................................................... ....11
BRAKE PAD : Inspection ........................................11
DISC ROTOR ......................................................... ....11
DISC ROTOR : Inspection ......................................11
REAR DISC BRAKE .........................................12
BRAKE PAD .......................................................... ....12
BRAKE PAD : Inspection .........................................12
DISC ROTOR ......................................................... ....12
DISC ROTOR : Inspection .......................................12
PERIODIC MAINTENANCE ........................13
BRAKE PEDAL ................................ .................13
Inspection and Adjustment .................................. ....13
BRAKE FLUID ................................. .................14
Drain and Refill .................................................... ....14
Bleeding Brake System ...........................................14
FRONT DISC BRAKE .......................................16
Brake Burnishing ................................................. ....16
REAR DISC BRAKE .........................................17
Brake Burnishing ................................................. ....17
REMOVAL AND INSTALLATION ...............18
BRAKE PEDAL ................................ .................18
Exploded View ..................................................... ....18
Removal and Installation .........................................18
BRAKE PIPING ................................ .................20
FRONT ................................................................... ....20
FRONT : Exploded View .........................................20
FRONT : Hydraulic Piping .......................................21
FRONT : Removal and Installation ..........................21
REAR ..................................................................... ....23
REAR : Exploded View ............................................23
REAR : Hydraulic Piping ..........................................24
REAR : Removal and Installation ............................24
BRAKE MASTER CYLINDER ..........................26
Exploded View .........................................................26
Removal and Installation .........................................26
Revision: November 20132014 Altima NAM

BR-4
< PRECAUTION >
PRECAUTIONS
• Tighten the brake tube flare nut to the specified torque with
crowfoot (A) and torque wrench (B).
• Always confirm the specified ti ghtening torque when install-
ing the brake pipes.
• Turn the ignition switch OFF and disconnect the ABS actuator
and electric unit (control unit) connector or the battery nega-
tive terminal before performing the work.
• Check that no brake fluid leakage is present after replacing the parts.
• Burnish the brake contact surf aces after refinishing or replac-
ing rotors, after replacing pads, or if a soft pedal occurs at
very low mileage.
- Front brake: refer to BR-16, "Brake Burnishing"
.
- Rear brake: refer to BR-17, "Brake Burnishing"
.
JPFIA0001ZZ
Revision: November 20132014 Altima NAM

PREPARATIONBR-5
< PREPARATION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
PREPARATION
PREPARATION
Special Service ToolINFOID:0000000009463679
The actual shape of the tools may di ffer from those illustrated here.
Commercial Service ToolINFOID:0000000009463680
Tool number
(TechMate No.)
Tool name Description
—
(J-46532)
Brake height tool Measuring brake pedal height
38-PFM92
(—)
Pro-Cut 9.2 Lathe Refinishing rotors
LFIA0227E
ALFIA0092ZZ
Tool name
Description
1. Flare nut crowfoot
2. Torque wrench Removing and installing brake piping
a: 10mm (0.39 in)/12mm (0.47 in)
Power tool Loosening nuts, screws and bolts
NT360
PIIB1407E
Revision: November 20132014 Altima NAM

BR-6
< SYSTEM DESCRIPTION >
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYSTEM DESCRIPTION
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting ChartINFOID:0000000009463681
Use the chart below to help you find the cause of the sy mptom. If necessary, repair or replace these parts.
×: ApplicableReference page
BR-11, "BRAKE PAD : Inspection"
,
BR-12
BR-11
, BR-12
BR-11
, BR-12—
—
BR-11, "DISC ROTOR : Inspection", BR-12, "DISC ROTOR : Inspection"—
—
—
BR-11, "DISC ROTOR : Inspection", BR-12, "DISC ROTOR : Inspection"
PB-6, "Inspection"
FAX-5, "NVH Troubleshooting Chart"
, RAX-4, "NVH Troubleshooting Chart"
FSU-6, "NVH Troubleshooting Chart"
,RSU-4, "NVH Troubleshooting Chart"
FAX-5, "NVH Troubleshooting Chart"
(front axle), RAX-4, "NVH Troubleshooting Chart"
(rear axle)
WT-52, "NVH Troubleshooting Chart"
WT-52, "NVH Troubleshooting Chart"FAX-5, "NVH Troubleshooting Chart"ST-29, "NVH Troubleshooting Chart"
Possible cause and
SUSPECTED PARTS
Pads - damaged
Pads - uneven wear
Shims damaged
Rotor imbalance
Rotor damage
Rotor runout
Rotor deformation
Rotor deflection
Rotor rust
Rotor thickness variation
Drum out of round
WHEEL HUB
SUSPENSION
AXLE
TIRES
ROAD WHEEL
DRIVE SHAFT
STEERING
Symptom Noise
××× ××× ×××
××
Shake × ×× ×××
××
Shimmy, Shudder ×××××××× × ××× ×
Revision: November 20132014 Altima NAM

FRONT DISC BRAKEBR-11
< BASIC INSPECTION >
C
D E
G H
I
J
K L
M A
B
BR
N
O P
FRONT DISC BRAKE
BRAKE PAD
BRAKE PAD : InspectionINFOID:0000000009463687
PA D W E A R
Check brake pad thickness from an inspection hole on caliper body.
Check using a scale if necessary.
DISC ROTOR
DISC ROTOR : InspectionINFOID:0000000009463688
APPEARANCE
Check surface of disc rotor for uneven wear, cracks or damage. Replace if any abnormal conditions exist.
RUNOUT
1. Check the wheel bearing axial end play before the inspection. Refer to FAX-6, "Inspection".
2. Secure the disc rotor to the wheel hub and bearing assembly with wheel nuts at two wheel nut locations.
3. Inspect the runout with a dial gauge, measured at 10 mm (0.39 in) inside the disc edge.
4. Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing assembly installation
position by one hole at a time if the runout exceeds the limit
value.
5. Refinish the disc rotor if the runout is outside the limit even after performing the above operation. When refinishing, use Tool.
THICKNESS
Check the thickness of the disc rotor using a micrometer. Replace
the disc rotor if the thick ness is below the wear limit.
Wear limit thickness : Refer to
BR-49, "Front Disc
Brake".
ALFIA0271ZZ
Runout : Refer to BR-49, "Front Disc Brake".
Tool number : 38-PFM90.5 ( — )
SBR019B
Wear thickness : Refer to BR-49, "Front Disc
Brake".
Thickness variation : Refer to BR-49, "Front Disc
Brake".
SBR020B
Revision: November 20132014 Altima NAM

BR-12
< BASIC INSPECTION >
REAR DISC BRAKE
REAR DISC BRAKE
BRAKE PAD
BRAKE PAD : InspectionINFOID:0000000009463689
PA D W E A R
Check pad thickness from an inspection hole on caliper body. Check
using a scale if necessary.
DISC ROTOR
DISC ROTOR : InspectionINFOID:0000000009463690
APPERANCE
Check surface of disc rotor for uneven wear, cracks or damage. Replace if any abnormal conditions exist.
RUNOUT
1. Check the wheel bearing axial end play before the inspection. Refer to RAX-8, "Wheel Hub Bearing".
2. Secure the disc rotor to the wheel hub and bearing assembly with wheel nuts at two wheel nut locations.
3. Inspect the runout with a dial gauge, measured at 10 mm (0.39 in) inside the disc edge.
4. Find the installation position with a minimum runout by shifting the disc rotor-to-wheel hub and bearing assembly installation
position by one hole at a time if the runout exceeds the limit
value.
5. Refinish the disc rotor if the runout is outside t he limit even after performing the above operation. When
refinishing, use Tool.
Thickness
Check the thickness of the disc ro tor using a micrometer. Replace
the disc rotor if the thickness is below the minimum thickness. Wear limit thickness : Refer to
BR-49, "Rear Disc
Brake".
ALFIA0272ZZ
Runout : Refer to BR-49, "Rear
Disc Brake".
Tool number : 38-PFM90.5 ( — )
SBR019B
Minimum thickness : Refer to BR-49, "Rear Disc
Brake".
Thickness variation : Refer to BR-49, "Rear Disc
Brake".
SBR020B
Revision: November 20132014 Altima NAM