2014 NISSAN TEANA mirror

DOOR MIRRORMIR-21
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
4. Remove the door mirror nuts (A) and the door mirror assembly (1).
INSTALLATION
Installation is in the reverse order of removal. Door mirror nut: : 5.1 N·m (0.5 kg-m, 4 ft-lb)
ALLIA1161ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-22
< REMOVAL AND INSTALLATION >
DOOR MIRROR GLASS
DOOR MIRROR GLASS
Removal and InstallationINFOID:0000000009463533
REMOVAL
1. Position the door mirror glass surface upward.
2. Apply protective tape (A) to mirror housing.
3. Insert a suitable tool (B) as shown and gently release the door mirror glass (1) from the door mirror actuator.
CAUTION:
Do not use excessive force or damage or breakage of the
door mirror glass could occur.
INSTALLATION
Installation is in the reverse order of removal.
AWLIA1999ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRROR REAR FINISHERMIR-23
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR REAR FINISHER
Removal and InstallationINFOID:0000000009463534
REMOVAL
1. Remove the door mirror glass. Refer to MIR-22, "Removal and Installation".
2. Release the door mirror rear finisher pawls (A) using a suitable tool.
3. Remove the door mirror rear finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check that pawls are securely engaged.
ALLIA1175ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-24
< REMOVAL AND INSTALLATION >
DOOR MIRROR ACTUATOR
DOOR MIRROR ACTUATOR
Removal and InstallationINFOID:0000000009463535
REMOVAL
1. Remove the door mirror glass. Refer to MIR-22, "Removal and Installation".
2. Remove the mirror actuator screw (A).
3. Release the door mirror actuator pawls (A) using a suitable tool. : Pawl
4. Disconnect the harness connector fr om the door mirror actuator
(1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALLIA1169ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRROR REMOTE CONTROL SWITCHMIR-25
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and InstallationINFOID:0000000009463536
REMOVAL
1. Release the pawls and remove the front door pull handle outer finisher. Refer to INT-15, "Exploded View".
2. Disconnect the harness connector from the door mirror remote control switch.
3. Release the pawls and remove the door mirror remote control switch from the front door finisher.
INSTALLATION
Installation is in the reverse order of removal.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MWI
NORMAL OPERATING CONDITIONMWI-81
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K L
M B
A
O P
NORMAL OPERATING CONDITION
COMPASS
COMPASS : DescriptionINFOID:0000000009461756
COMPASS
• The electronic compass is highly protected from changes in most magnetic fields. However, some large
changes in magnetic fields can affect it. Some exampl es are (but not limited to): high tension power lines,
large steel buildings, subways, steel bridges, automatic car washes, large piles of scrap metal, etc. While
this does not happen very often, it is possible.
• During normal operation, the Compass Mirror will cont inuously update the compass calibration to adjust for
gradual changes in the vehicle's magnetic "remnant" field. If the vehicle is subjected to high magnetic influ-
ences, the compass may appear to indicate false headings , become locked, or appear that it is unable to be
calibrated. If this occurs, perform the calibration procedure.
• If at any time the compass continually displays the inco rrect direction or the reading is erratic or locked, ver-
ify the correct zone variance.
Symptom Chart
Symptom Cause Solution / Reference
The compass display reads "C".
• Compass is not calibrated.
• Incorrect zone variance setting.
• Large change in magnetic field (Steel bridges, subways, concentrations of
metal, car washes, etc.)
• Compass was calibrated incorrectly or
in the presence of a strong magnetic
field. Perform Calibration. Refer to
MWI-16,
"COMPASS : Description".
Compass shows the wrong direction.
Compass does not change direction ap-
pears "Locked".
Compass does not show all the directions,
one or more is missing.
The compass was calibrated but it "loses"
calibration.
On long trips the compass shows the
wrong direction. Perform Zone Variatio
n Setting if correct
reading is desired in that location. Refer to
MWI-16, "COMPASS : Description"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PCS
DIAGNOSIS SYSTEM (BCM)PCS-41
< SYSTEM DESCRIPTION > [POWER DISTRIBUTION SYSTEM]
C
D E
F
G H
I
J
K L
B
A
O P
N
WORK SUPPORT
PUSH SWITCH INDICATOR This test is able to check push-button ignition switch indicator operation [On/Off].
ACC CONT This test is able to check ac cessory relay control operation [On/Off].
IGN CONT1 This test is able to check ignition relay-1 control operation [On/Off].
ST CONT LOW This test is able to check starter control relay operation [On/Off].
IGNITION RELAY This test is able to ignition relay operation [On/Off].
REVERSE LAMP TEST This test is able to check reverse lamp illuminatio n operation [On/Off].
TRUNK/LUGGAGE LAMP TEST This test is able to check cargo lamp illumination operation [On/Off].
KEYFOB PW TEST This test is able to check power window operation using the Inte lligent Key [Off/DOWN/UP].
SHIFTLOCK SOLENOID TEST This te st is able to check shift lock solenoid operation [On/Off].
Test Item Description
Support Item Setting Description
IGN/ACC BATTERY SAVER On* Battery saver function ON.
Off Battery saver function OFF.
REMOTE ENGINE STARTER On* Remote engine start function ON.
Off Remote engine start function OFF.
ANSWERBACK I-KEY LOCK UNLOCK BUZZER Buzzer reminder function by door lock/unlock request switch ON.
HORN Horn chirp reminder function by door lock request switch ON.
Off* No reminder function by door lock/unlock request switch.
INVALID This mode is not used.
ANSWERBACK KEYLESS LOCK UN-
LOCK On
Buzzer or horn chirp reminder when doors are locked/unlocked with
Intelligent Key.
Off* No buzzer or horn chirp reminder when doors are locked/unlocked
with Intelligent Key.
ANSWER BACK On* Horn chirp reminder when doors are locked with Intelligent Key.
Off No horn chirp reminder when doors are locked with Intelligent Key.
RETRACTABLE MIRROR SET On Retractable mirror set ON.
Off* Retractable mirror set OFF.
CONFIRM KEY FOB ID — Intellige nt Key ID code can check.
LOCK/UNLOCK BY I-KEY On* Door lock/unlock function from Intelligent Key ON.
Off Door lock/unlock function from Intelligent Key OFF.
ENGINE START BY I-KEY On* Engine start function from Intelligent Key ON.
Off Engine start function from Intelligent Key OFF.
TRUNK/GLASS HATCH OPEN On* Buzzer reminder function by trunk opener request switch ON.
Off Buzzer reminder function by trunk opener request switch OFF.
INTELLIGENT KEY LINK SET On Intelligent Key link set ON.
Off* Intelligent Key link set OFF.
SHORT CRANKING OUTPUT Start70 msec
Starter motor operation duration times.
100 msec
200 msec
End —
INSIDE ANT DIAGNOSIS — This function allo ws inside key antenna self-diagnosis.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

PG-56
< DTC/CIRCUIT DIAGNOSIS >
HARNESS
ROOM LAMP HARNESS
AAMIA0030ZZ
C 5 R 1 W / 1 2 : To M 7 C 2 R 7 W / 4 : M i c r o p h o n e
B 5 R 2 W / 4 : To M 1 3 B 4 R 8 B / 7 : Auto anti-dazzling inside mirror
(Without homelink universal transceiver)
C 3 R 3 W / 2 : Va n i t y m i r r o r l a m p L H B2 R9 W/2 : Vanity mirror lamp RH
B 4 R 4 B / 1 0 : Auto anti-dazzling
inside mirror (With
homelink universal transceiver) E 3 R 5 0 W / 8 : P e r s o n a l l a m p r e a r
Revision: November 20132014 Altima NAM