Page 3237 of 4801
INSIDE MIRRORMIR-7
< WIRING DIAGRAM >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
ABLIA5191GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3238 of 4801
MIR-8
< WIRING DIAGRAM >
DOOR MIRROR
DOOR MIRROR
Wiring Diagram INFOID:0000000009463525
ABLWA2248GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3239 of 4801
DOOR MIRRORMIR-9
< WIRING DIAGRAM >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
ABLIA5202GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3240 of 4801
MIR-10
< WIRING DIAGRAM >
DOOR MIRROR
ABLIA5192GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3241 of 4801
DOOR MIRRORMIR-11
< WIRING DIAGRAM >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
ABLIA5203GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3242 of 4801
MIR-12
< WIRING DIAGRAM >
DOOR MIRROR
ABLIA5193GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3249 of 4801
INSIDE MIRRORMIR-19
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded ViewINFOID:0000000009463529
Removal and InstallationINFOID:0000000009463530
REMOVAL
1. Remove the inside mirror base screw.
2. Disconnect the harness connector from the inside mirror.
3. Slide the inside mirror upward and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Apply Genuine Mirror Adhesive or equivalent to bonding surface of mirror base. Refer to GI-21, "Rec-
ommended Chemical Products and Sealants".
1. Inside mirror harness 2. I nside mirror 3. Mirror base
A. Screw
ALLIA1157ZZ
ALKIA0069GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 3250 of 4801
MIR-20
< REMOVAL AND INSTALLATION >
DOOR MIRROR
DOOR MIRROR
Exploded ViewINFOID:0000000009463531
Removal and InstallationINFOID:0000000009463532
REMOVAL
1. Remove the front door finisher. Refer to INT-15, "Removal and Installation".
2. Disconnect the harness connectors (A) from the door mirror cor- ner finisher.
3. Release the clips and pawls using a suitable tool and remove the door mirror corner finisher (1).
• Push suitable trim tool underneath finisher, and then pry out- ward as shown. Move tool further up near upper fastened
area, and then pry outward again.
: Clip
: Pawl
1. Door mirror cover 2. Side turn signal lamp (if equipped) 3. Door mirror housing assembly
4. Door mirror actuator 5. Door mirror glass and holder
ALLIA1166ZZ
AWLIA2218ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM