2013 Lexus CT200h Owner's Manual (in English)

5497-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Right side
Move the washer fluid filler opening. (P. 541)
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
4

5507-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Rear turn signal lights
Open the back door and
remove the covers and bolts,
and remove the lamp assembly
by pulling it directly backward
from the rear of the vehicle.
Use a flathead screwdriver
wrapped in a cloth.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
1
2
3
4

5517-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Back-up light/rear fog light
Open the back door and
remove the cover.
Use a flathead screwdriver
wrapped in a cloth.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
When installing, reverse the steps listed.
The illustrations show the removal of a back-up light from a right-hand
drive vehicle.
1
2
3
4

5527-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Outer foot lights
Press the upper part of the out-
side rear view mirror to tilt the
mirror face upward, and apply
protective tape to the lower
part of the mirror cover.
Insert 2 flathead screwdrivers
wrapped in protective tape,
and disconnect the tabs behind
the mirror.
Pry the mirror out toward you,
disconnecting the tabs 2 at a time.
Work carefully, ensuring that you
do not drop the mirror.
Disconnect the connectors
behind the mirror, and remove
the mirror.
When removing the thin connec-
tors, make sure to mark one of the
connectors with a piece of tape, to
avoid mixing them up when rein-
stalling.
Work carefully, ensuring that you
do not drop the mirror.
When handling the mirror, do not
touch the parts applied with
grease.
The number of connectors
equipped differs by vehicle speci-
fication.
1
2
3

5537-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Remove the screws and take
off the mirror cover.
Turn the bulb base counter-
clockwise.
Remove the light bulb.
After installing the new bulb,
secure the socket to the light
body.
When inserting the socket, align
the marks printed on the light
body and the socket.
4
5
6
7

5547-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Install the visor cover on the
mirror frame, secure it with a
screw, and install the side turn
signal light and outer foot
light.
Use only the screw position
shown in the illustration.
Side turn signal light: Align the
tabs on the light and the cover and
install.
Outer foot light: Interlock the tabs
in the groove of the light body
with those on the cover, and
secure.
Disconnect the tabs, and sepa-
rate the top and bottom of the
rear side cover of the mirror.
8
9

5557-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
7
Maintenance and care
Install the cover of the back
end of the mirror, installing the
lower side and the upper side
in that order.
When installing the lower side of
the cover, insert the side turn sig-
nal light pin into the hole in the
cover.
Secure the cover with screws
and reconnect the connectors
back together.
Secure the cords by returning
them to the hooks as they were.
Align the tabs, and secure the
mirror by pushing in each
diagonally-opposite pair of
tabs in order.
Make sure to insert the tabs in
order as shown in the illustration,
and push them in until a click is
heard.
If you do not hear the click, do
not force the tabs in. Instead,
remove the mirror and check that
the tabs are aligned.
10
11
12

5567-3. Do-it-yourself maintenance
CT200h_OM_OM76102E_(EE)
Replacing the following bulbs
If any of the lights listed below has burnt out, have it replaced by any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
Headlight low beams (LED type)
Daytime running lights and front position lights
LED front fog lights (if equipped)
Side turn signal lights
Stop/tail lights
High mounted stoplight
License plate lights
After replacing the bulbs
LED lights
The headlight low beams (LED type), front position lights, daytime running
lights, LED front fog lights (if equipped), side turn signal lights, stop/tail lights,
high mounted stoplight and license plate lights consist of a number of LEDs. If
any of the LEDs burn out, take your vehicle to any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional to have the light
replaced.
Condensation build-up on the inside of the lens
Temporary condensation build-up on the inside of the headlight lens does not
indicate a malfunction. Contact any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional for more information in the fol-
lowing situations:
Large drops of water have built up on the inside of the lens.
Water has built up inside the headlight.
When replacing light bulbs
P. 537 After removing the power control unit
cover, return the cover to original position
with the clips.
Push up center portion
Insert
Press
1
2
3