2013 Lexus CT200h Owner's Manual (in English)

161
3 3-3. Adjusting the seats
Operation of each component
CT200h_OM_OM76102E_(EE)
Rear seats
Pull up the seatback lock release
lever until the lock is released, and
fold the seatback down.
To avoid trapping the seat belt
between the seat and the inside of
the vehicle, pass the seat belt inside
the seat belt guide and then return
the seatback securely to the locked
position.
The seatbacks of the rear seats can be folded down.
Folding down the rear seatbacks
Returning the rear seatbacks
Seat belt

1623-3. Adjusting the seats
CT200h_OM_OM76102E_(EE)
WA R N I N G
When folding the rear seatbacks down
Observe the following precautions. Failure to do so may result in death or seri-
ous injury.
Do not fold the seatbacks down while driving.
Stop the vehicle on level ground, set the parking brake and shift the shift posi-
tion to P.
Do not allow anyone to sit on a folded seatback or in the luggage compart-
ment while driving.
Do not allow children to enter the luggage compartment.
When returning the rear seatback to the upright position
Do not put your hand on the seat belt guide.
Doing so may cause you to trap your hand between the guide and the pillar,
causing an injury.
After returning the rear seatback to the upright position
Observe the following precautions. Failure to do so may result in death or seri-
ous injury.
Check that the seat belts are not twisted or caught in the seatback.
Make sure that the seatback is securely
locked in position by lightly pushing it
back and forth.
If the seatback is not securely locked, the
red marking will be visible behind the
seatback lock release lever. Make sure
that the red marking is not visible.

163
3 3-3. Adjusting the seats
Operation of each component
CT200h_OM_OM76102E_(EE)
Driving position memory
Your preferred driving position (the position of the driver’s seat and out-
side rear view mirrors) can be recorded and recalled by pressing a button.
Three different driving positions can be recorded into memory.
Recording procedure
Turn the power switch to ON mode.
Check that the shift position is in P.
Adjust the driver’s seat and outside rear view mirrors to the desired
positions.
While pressing the “SET” but-
ton, or within 3 seconds after
the “SET” button is pressed,
press button “1”, “2” or “3”
until the buzzer sounds.
If the selected button has already
been preset, the previously
recorded position will be over-
written.
: If equipped
This feature automatically adjusts the driver’s seat and outside rear view
mirrors to suit your preferences.
Driving position memory
1
2
3
4

1643-3. Adjusting the seats
CT200h_OM_OM76102E_(EE)
Recall procedure
Turn the power switch to ON mode.
Check that the shift position is in P.
Press one of the buttons for the
driving position you want to
recall until the buzzer sounds.
To stop the position recall operation part-way through
Perform any of the following:
Press the “SET” button.
Press button “1”, “2” or “3”.
Operate any of the seat adjustment switches (only cancels seat position recall).
Seat positions that can be memorized (P. 159)
The adjusted positions other than the position adjusted by lumbar support switch
can be recorded.
Operating the driving position memory after turning the power switch off
Recorded seat positions can be activated up to 180 seconds after the driver’s door
is opened and another 60 seconds after it is closed again.
In order to correctly use the driving position memory function
If a seat position is already in the furthest possible position and the seat is oper-
ated in the same direction, the recorded position may be slightly different when it
is recalled.
1
2
3

1653-3. Adjusting the seats
3
Operation of each component
CT200h_OM_OM76102E_(EE)
Each electronic key (including a card key) can be registered to recall your
preferred driving position.
Registering procedure
Record your driving position to button “1”, “2” or “3” before perform-
ing the following:
Carry only the key you want to register, and then close the driver’s
door.
If 2 or more keys are in the vehicle, the driving position cannot be
recorded properly.
Turn the power switch to ON mode.
Check that the shift position is in P.
Recall the driving position that you want to record.
While pressing the recalled
button, press and hold the door
lock switch (either lock or
unlock) until the buzzer
sounds.
If the button could not be regis-
tered, the buzzer sounds continu-
ously for approximately 3
seconds.
Recall procedure
Carry the electronic key that has been registered to the driving posi-
tion, and then unlock and open the driver’s door using the smart entry
& start system or wireless remote control.
The driving position will move to the recorded position.
If the driving position is in a position that has already been recorded, the
seat and outside rear view mirrors will not move.
Memory recall function
1
2
3
4

1663-3. Adjusting the seats
CT200h_OM_OM76102E_(EE)
Cancelation procedure
Carry only the key you want to cancel and then close the driver’s door.
If 2 or more keys are in the vehicle, the driving position cannot be can-
celed properly.
Turn the power switch to ON mode.
While pressing the “SET” button, press and hold the door lock
switch (either lock or unlock) until the buzzer sounds twice.
If the button could not be canceled, the buzzer sounds continuously for
approximately 3 seconds.
Recalling the driving position using the memory recall function
Different driving positions can be registered for each electronic key. Therefore,
the driving position that is recalled may be different depending on the key being
carried.
If a door other than the driver’s door is unlocked with the smart entry & start
system, the driving position cannot be recalled. In this case, press the driving
position button which has been set.
WA R N I N G
Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear passen-
ger or squeeze your body against the steering wheel.
1
2

167
3 3-3. Adjusting the seats
Operation of each component
CT200h_OM_OM76102E_(EE)
Head restraints
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
Head restraints are provided for all seats.
Front seats
Lock release but-
1
2
Rear seats
Lock release but-
1
2

1683-3. Adjusting the seats
CT200h_OM_OM76102E_(EE)
Removing the head restraints
Installing the head restraints
Adjusting the height of the head restraints (front seats)
Adjusting the rear seat head restraint
Always raise the head restraint one level from the stowed position when using. Pull the head restraint up while pressing the
lock release button.
Align the head restraint with the installation
holes and push it down to the lock position.
Press and hold the lock release button when
lowering the head restraint.
Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.
Lock release but-
Lock release but-