2013 Lexus CT200h Owner's Manual (in English)

6058-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
8
When trouble arises
If you have a flat tire (vehicles without a spare tire)
Stop the vehicle in a safe place on a hard, flat surface.
Set the parking brake.
Shift the shift position to P.
Stop the hybrid system.
Turn on the emergency flashers.
Your vehicle is not equipped with a spare tire, but instead is equipped
with an emergency tire puncture repair kit.
A puncture caused by a nail or screw passing through the tire tread can be
repaired temporarily with the emergency tire puncture repair kit.
WA R N I N G
If you have a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel
beyond repair, which could result in an accident.
Before repairing the vehicle

6068-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
*: Use of the jack (P. 596)
Location of the emergency tire puncture repair kit, jack and tools
Towing eyelet
Emergency tire puncture repair
kit
Jack
*
Wheel nut wrench
Jack handle1
2
3
4
5

6078-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
8
When trouble arises
Emergency tire puncture repair kit components
Bottle
Air pressure gauge
Compressor switch
Air release capStickers
Hose
Power plug
Insertion key1
2
3
4
5
6
7
8

6088-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
Remove the center deck board.
Remove the center auxiliary box.
Take out the emergency tire
puncture repair kit.
Taking out the emergency tire puncture repair kit
1
2
3

6098-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
8
When trouble arises
Remove the center deck board and center auxiliary box. (P. 608)
Remove the hook and then
loosen and take out the jack.
For loosening
For tightening
When storing the jack, put it into
the tray and tighten it until fixed
to the tray.
Use of the jack: P. 596
Check the degree of the tire damage.
A tire should only be repaired with
the emergency tire puncture repair
kit if the damage is caused by a nail
or screw passing through the tire
tread.
• Do not remove the nail or screw
from the tire. Removing the
object may widen the opening
and disenable emergency repair
with the kit.
• To avoid sealant leakage, move
the vehicle until the area of the
puncture, if known, is positioned
at the top of the tire.
Taking out the jack
1
2
1
2
Before performing emergency repair

6108-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
Pull the insertion key out of the
kit.
Place the kit with the bottom fac-
ing upward.
Peel off the label, and push in the
insertion key until a click is heard.
Return the kit to an upright posi-
tion and make sure that the com-
pressor switch is off.
Use the kit with the top facing
upward.
Connect the power plug to the
power outlet socket. (P. 475)
Emergency repair method
1
2
3
4

6118-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
8
When trouble arises
Remove the valve cap from the
valve of the punctured tire.
Remove the air release cap from
the hose.
Connect the hose to the valve.
Screw the end of the hose clockwise
as far as possible.
Check the specified tire inflation
pressure.
Tire inflation pressure is specified
on the label as shown. (P. 645)
Start the hybrid system. (P. 196)
5
6
7
8
9

6128-2. Steps to take in an emergency
CT200h_OM_OM76102E_(EE)
To inject the sealant and inflate
the tire, turn the compressor
switch on.
Use the kit with the top facing
upward.
Inflate the tire until the recom-
mended pressure is reached.
The sealant will be injected
and the pressure will spike to
300 kPa (3.0 kgf/cm
2 or bar,
44 psi) or 400 kPa (4.0 kgf/
cm
2 or bar, 58 psi), then gradu-
ally decrease.
The air pressure gauge will
display the actual tire inflation
pressure about 1 minute after
the switch is turned on.
• Turn the compressor switch
off and then check the tire
inflation pressure. Being
careful not to over inflate,
check and repeat the infla-
tion procedure until the rec-
ommended tire inflation
pressure is reached.
10
11
1
2